These grips are sized to fit in tight areas.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Made of nylon, these grips resist chemicals.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Tighten the screws to secure your cable.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

These grips have a thin, flexible seal that covers the holes until you push cords through.

The loops tighten by the weight of your cable or by manual adjustment. These grips are often wrapped around a beam or pipe.

Made of stainless steel, these grips have excellent corrosion resistance.

These are tin-plated bronze.

The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Snap these grommets into place to hold wire, cable, and cords in wet locations and form a seal against dust, debris, and water.

Create a tight seal around wire, cable, and cords with these grommets to keep out dust, debris, and moisture.

Push these flexible grommets into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration.

Cut the thin layer of rubber in the center of these grommets to create custom IDs to securely hold and protect wire, cable, and cords. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration. Also known as webbed grommets.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes.

These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.

Squeeze these flexible grommets to open the center flap—once wire, cable, and cords pass through, the flap closes tightly for dust and debris protection as well as a finished look. Use them to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Wire, cable, and cords pass through the grommet opening while the bristles fill in the gaps to control dust and debris. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.