This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Use this shielded sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

This sleeving stretches to fit over items for easy installation, and then tightens around its contents for a secure fit. Choose from multiple colors to organize wire and cable.

Braided from thick plastic strands, this sleeving has excellent abrasion resistance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Reduce the likelihood of slipping in high-traffic areas. This sleeving has thick, nonslip fibers that create friction so it doesn’t slide when you step on it. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

Made of PVC, this sleeving resists chemicals, oil, and acids.

A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

Made of neoprene rubber, this sleeving has excellent abrasion resistance. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.

The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.

Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.

Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.

Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.

Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.

A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.

After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.

Keep general purpose tubing in a variety of sizes on hand.

Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.

A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.

Create a permanent seal without applying heat. This tubing is also known as cold-shrink tubing.

Insulate wire and cable splices, wrap wire harnesses, and repair cable jacketing with this stretchy tape.

Also known as Scotchfil, this noncorrosive putty tape wraps, stretches, and molds around irregular shapes for insulation buildup.

Use this rubber tape to splice cable in high-voltage applications.

At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.

This puncture- and cut-resistant cotton tape is coated with a high-grade electrical-insulating varnish. Also known as cambric tape.

Use this tape to modify printed circuit boards, shield components, and prototype wiring-board layout and design.

The adhesive on this conformable aluminum foil tape is electrically conductive for use on surfaces that can't be soldered. Use it to shield cables and electronic components from EMI (electromagnetic interference).

Also known as skived tape, this low-friction tape stretches to conform to irregular surfaces.

Backed with 3M VHB 4941 foam adhesive for strength, padding, and vibration resistance.

PEEK offers the best wear and abrasion resistance of our low-friction tapes. Use it for wire wraps and sliding bearing surfaces.

Providing all-weather corrosion protection, this vinyl tape resists salt water, UV light, acids, and alkalies. Use it to wrap pipes and electrical conduit both above and below ground.

Aluminum foil is laminated to a tough fiberglass cloth to form a high-strength, reflective tape that resists temperatures up to 500° F. Use it for flame-spray masking and wire harness heat shielding.