Work-Positioning Holders

A plastic pad on the gripping surface of these clamps prevents workpiece marring, making them useful for holding polished surfaces and reducing the need for secondary finishing steps.

Fingertip Setup Clamps

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Setup Clamp Supports

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

Setup Clamps for Angled Workpieces

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

Side Clamps

Also known as toe clamps, these grip the side of a workpiece to leave the top free for machining.

T-Slot Side Clamps

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Vise Mounting Clamps

Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.

Hold-Down Machine Table Clamps

An alternative to setup clamps, these heavy duty clamps have high holding power to secure workpieces during machining.

Machine Table Clamps for Round Workpieces

Use these clamps to hold large round parts for machining. Each clamp comes with five lengths of chain that combine to accommodate different size workpieces.

Fixture Clamps

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Machinable Fixture Clamps

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Fixture Clamps for Castings and Rough Parts

Unlike the smooth and flat edges of standard fixture clamps, these clamps have ridges that bite into parts, making them good for gripping castings and rough-cut stock.

Low-Profile Fixture Clamps

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Machinable Low-Profile Fixture Clamps

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Dual-Clamping Fixture Clamps

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Machinable Dual-Clamping Fixture Clamps

Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.

Hold-Down Fixture Clamps

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Threaded Air-Powered Hold-Down Fixture Clamps

Screw these clamps directly into a tapped hole in a fixture.

Air-Powered Hold-Down Fixture Clamps

Mount using the holes in the base.

Hydraulic-Powered Hold-Down Fixture Clamps

Use the power of hydraulic fluid to quickly, consistently, and repeatedly clamp and release parts with a greater clamping force than air-powered hold-down fixture clamps.

Inside Diameter Fixture Clamps

Secure a workpiece from the inside, leaving the outside clear for machining.

Inside Diameter Fixture Clamps
for Castings and Rough Parts

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

Ball-Lock Quick-Change Fixture Clamps

Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".

Hold-Down Toggle Clamps

Low-Profile Hold-Down Toggle Clamps

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Low-Profile Hold-Down Toggle
Clamps with Extra Hand Clearance

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

Heavy Duty Low-Profile Hold-Down Toggle Clamps

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Low-Profile Hold-Down Toggle
Clamps with Locking Handle

Push the lever to lock the handle and prevent accidental opening.

Auto-Adjusting Low-Profile Hold-Down Toggle Clamps

Hold workpieces of different thicknesses without adjustment.

Hold-Down Toggle Clamps

Mount these clamps to a bench top or other surface to keep workpieces in place.

Nonreflective Hold-Down Toggle Clamps

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Heavy Duty Hold-Down Toggle Clamps

Auto-Adjusting Heavy Duty Hold-Down Toggle Clamps

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Hold-Down Toggle Clamps with Locking Handle

Push the lever to lock the handle and prevent accidental opening.

Compact Hold-Down Toggle Clamps

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Compact Hold-Down Toggle
Clamps with Locking Handle

Push the lever to lock the handle and prevent accidental opening.

Weld-On Side-Mount Hold-Down Toggle Clamps

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Side-Mount Hold-Down Toggle Clamps

Bolt to the side of an object. Often used to clamp lids and covers on containers.

Rail-Mount Hold-Down Toggle Clamps

The mounting base secures these clamps to a rail or bar.

Low-Profile Rail-Mount Hold-Down Toggle Clamps

The handle locks in a horizontal position for more clearance above the clamp.

Undermount Hold-Down Toggle Clamps

Mount these clamps below a surface.

Dual-Mount Hold-Down Toggle Clamps

Two sets of mounting holes allow mounting on the bottom or side.

Tips for Toggle Clamp Holding Screws

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

Holding Screws for Toggle Clamps

Replace worn screws or customize your clamps.

Dual-Mount Air-Powered Hold-Down Toggle Clamps

Long-Life Dual-Mount Air-Powered
Hold-Down Toggle Clamps

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

Air-Powered Hold-Down Toggle Clamps

These clamps have mounting holes on the bottom.

Bar-Style Hold-Down Clamps

Drop-In Bar-Style Hold-Down
Clamps for Workholding Tables

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

Bench-Mount Bar-Style Hold-Down Clamps

Mount the base to a work surface using screws.

Push/Pull Clamps

Push/Pull Toggle Clamps

Push or pull the plunger to hold your workpiece from the side.

Compact Push/Pull Toggle Clamps

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

Heavy Duty Reverse-Action Push Toggle Clamps

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Reverse-Action Push Toggle Clamps

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Auto-Adjusting Push Toggle Clamps

Hold workpieces of different thicknesses without adjustment.

Compact Push Toggle Clamps with Locking Handle

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

Push Toggle Clamps with Locking Handle

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

Push Toggle Clamps with Rotating Handle

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Sealed Push/Pull Toggle Clamps

Moving parts are sealed to prevent dirt and dust from clogging the clamp.

Hole-Mount Push/Pull Toggle Clamps

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Hole-Mount Push/Pull Toggle
Clamps with Locking Handle

Push the lever to lock the handle and prevent accidental opening.

Rail-Mount Push/Pull Toggle Clamps

Secure these clamps to a rail or bar.

Hole-Mount Adjustable-Travel Push/Pull Clamps

Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel.

Adjustable-Travel Push/Pull Clamps

The plunger can be locked at any position along its travel.

Air-Powered Push Toggle Clamps

Use for repetitive clamping and in production environments or hard-to-reach locations.

Spring Clamps

Miniature Spring Clamps

Clamp thin materials, or use in tight spaces.

Locking Miniature Spring Clamps

Press the lever to lock the clamp onto material.

Spring Clamps

Squeeze the handles to open the clamp; release and the spring holds it tightly in place.

Nonconductive Spring Clamps

All parts of these clamps are fiberglass, so they won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

Insulated Spring Clamps

These clamps meet DIN VDE 0680-1 for protection against accidental contact with live electrical circuits.

Extended-Reach Spring Clamps

The long, narrow jaws clamp farther into a workpiece and in tight spots.

Adjustable-Jaw Spring Clamps

Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.

Spring Clamps with Flexible Arm

Attached to an arm you can flex into position, these clamps hold objects such as a flashlight, tool, or instructions.

Spring Clamps with Telescoping Handle

Extend the handle to reach the clamp into tight spaces.

Plier Clamps

Locking Plier Clamps

Turn the knob to adjust the opening size.

Self-Adjusting Locking Plier Clamps

Squeeze the handles and the jaws will automatically adjust to fit your workpiece.

Bar-Style Locking Plier Clamps

Slide the upper jaw to adjust the opening size. These clamps hold larger workpieces than other locking plier clamps of similar size.

Bench-Mount Locking Plier Clamps

Mount to the top of your workbench.

Portable Bench-Top Locking Plier Clamps

A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.

Right-Angle Locking Plier Clamps for Sheets

Angled jaws clamp sheets, bars, and U-channels at 90°.

Locking Plier Clamps for Sheets

Press the lever down to lock these clamps, which fit in tight spaces and hold thin materials.

Locking Plier Spreaders

The jaws on these tools apply outward pressure for use as a spreader.

Pliers-Style Toggle Clamps

For repetitive clamping, turn the holding screw to adjust the opening size one time, and then use the handles to secure and release workpieces.

Plastic Plier Clamps

Use these tools for light duty clamping. Squeeze the handles to open; release to close.

Extended-Reach Plastic Plier Clamps

The long, pivoting jaws let you clamp farther into your workpiece and in tight spots.

Pliers-Activated Spring Clamps

Clamp thin sheet material together without drilling holes. These clamps open with special pliers and spring closed when the pliers are released.

Pliers-Activated Spring Clamp Sets

Set includes 12 clamps and the installation pliers required for positioning and removal.

Clothespins and Spring Clips

Hold lightweight objects, secure covers, and seal bags.

Latch-Style Clamps

Latch-Style Toggle Clamps with Locking Handle

Push the lever to lock the handle and prevent accidental opening.

Latch-Style Toggle Clamps

Fit the draw arm over a latch plate and pull the handle to clamp.

Heavy Duty Latch-Style Toggle Clamps

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Right-Angle Latch-Style Toggle Clamps

Mount the clamp on a lid and the latch plate on the side of a container.

Right-Angle Latch-Style Toggle
Clamps with Locking Handle

Push the lever to lock the handle and prevent accidental opening.

No-Twist C-Clamps

The jaws move in unison to apply even pressure and prevent twisting.

Bench-Mount No-Twist C-Clamps

Hold the workpiece down against a bench or table.

Nonmarring No-Twist C-Clamps

Plastic clamping surfaces prevent damage to material.

Three-Way No-Twist C-Clamps

Apply pressure to the side of a workpiece as well as the top and bottom.

C-Clamps

Turn the handle to tighten these multipurpose tools for strong clamping in nearly any application.

Heavy Duty C-Clamps

These clamps have twice the capacity of standard C-clamps.

Extra Heavy Duty C-Clamps

With five times the capacity of standard C-clamps, these are the highest capacity clamps we offer.

High-Visibility C-Clamps

A bright finish makes these clamps easy to see.

Nonmarring C-Clamps

Plastic clamping surfaces prevent damage to material.

Corrosion-Resistant C-Clamps

These clamps are made of stainless steel for excellent corrosion resistance.

Lightweight Aluminum C-Clamps

Lighter weight than other metal clamps, these are less likely to bend thin material.

Nonsparking C-Clamps

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Nonconductive C-Clamps

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

Three-Way C-Clamps

Three screws apply pressure to three sides of a workpiece.

Extended-Reach C-Clamps

Clamp farther in from the edge of a workpiece than with other C-clamps.

Low-Profile C-Clamps

With no handle or protruding screw, these clamps can fit into tight spaces.

Narrow-Body C-Clamps

The clamp body is extra-slim to fit into narrow openings.

C-Style Toggle Clamps

For repetitive clamping, turn the holding screw to adjust the opening size one time, and then use the handle to secure and release workpieces.

Swiveling Pads for C-Clamps

Replace a fixed clamping surface with a swiveling pad that compensates for uneven workpieces.

Fast-Action C-Clamps

Press the quick-release button and slide the screw into position to make adjustments in less time.

Screw Clamps

Swiveling Tips for Screws and Threaded Studs

Attach to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.

Swiveling Gripper Tips for Screws and Threaded Studs

Attach to the end of a screw or threaded stud—the serrated face swivels to grip uneven and angled surfaces. Also known as toggle and swivel-foot pads.

Nonmarring Swiveling Tips for
Screws and Threaded Studs

The contact area is covered in plastic to protect soft metal and polished surfaces. Attach these tips to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.

Screw Clamps

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.

Hole-Mount Screw Clamps

Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.

Revolving Screw Clamps

When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.

Quick-Clamping Coil-Threaded Rods, Screws, and Nuts

Combine fast-threading components to build a clamping assembly.

Magnetic Clamps

Adjustable-Angle Magnetic Clamps

Two clamps connected by a pivoting arm hold workpieces at nearly any angle.

Miniature Adjustable-Angle Magnetic Clamps

Sized for small parts and tight spaces, these clamps have a pivoting pad at each end to hold workpieces at any angle up to 180°.

Easy On/Off Adjustable-Angle Magnetic Clamps

Each arm has a handle for turning the magnets on and off.

Easy On/Off Magnetic Clamps

Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.

Magnetic Clamps

Hold magnetic workpieces in place with these clamps.

Outside-Clamping Magnetic Clamps

Clamp workpieces from the outside at a 90° angle, leaving the inside free for welding or fabrication.

Three-Axis Magnetic Clamps

Hold and align up to three workpieces at 90° angles.

Hole-Grip Clamps

Insert these clamps into drilled holes in sheet material to grip and align when riveting or welding.

Hole-Grip Clamp Sets

Sets include clamps with different ODs as well as installation pliers.

Corner Clamps

Three-Axis Corner Clamps

Clamp up to three workpieces at 90° angles.

Corner Clamps

Hold workpieces at a 90° angle.

Heavy Duty Corner Clamps

With five times the capacity of standard corner clamps, these secure two workpieces at a 90° angle.

Adjustable-Angle Corner Clamps

Position workpieces at any angle from 0° to 180°.

Heavy Duty Adjustable-Angle Corner Clamps

The clamping surfaces pivot individually to secure workpieces of different thicknesses at any angle from 5° to 180°.

Frame Clamps

Grip all four corners of a rectangular workpiece.

Pipe Joining and Welding Clamps

Heavy Duty Chain Clamps for Pipe Joining and Welding

The open clamp design permits welding around almost the entire pipe circumference. A combination of chains and support bars hold a variety of pipe sizes.

Pipe Joining and Welding Clamps

Hold pipe and fittings together for tack welding.

Bar Clamps

Pull the lever to slide the clamping arm along the bar; release to lock in place.

Heavy Duty Bar Clamps

Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.

Any-Length Bar Clamps

Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

Vibration-Resistant Fast-Action Bar Clamps

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

Heavy Duty Fast-Action Bar Clamps

These clamps have twice the capacity of standard fast-action bar clamps.

Extra Heavy Duty Fast-Action Bar Clamps

For the most demanding jobs, these clamps have almost five times the capacity of standard fast-action bar clamps.

Trigger-Action Bar Clamps

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

Tight-Clearance Any-Length Bar Clamps

All adjustments can be made from one end, allowing clamping in tight spaces.

Fast-Action Bar Clamps

The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.

Edge-Clamping Adapters for Bar Clamps

Attach to your bar clamp to hold material on three sides.

Trigger-Action Bar Clamps/Spreaders

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

Fast-Action Bar Clamps/Spreaders

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Bar Clamps for Recessed Areas

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

Bar Clamps for Round and Angled Material

Two swivel pads on each jaw pivot to grip nearly any shape of material.

Parallel-Jaw Bar Clamps/Spreaders

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

Extended-Reach Bar Clamps

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

Band Clamps

An easy-to-tighten band encircles and holds round and odd-shaped objects with even pressure.

Panel-Alignment Suction-Cup Clamps

Quickly align, level, and join two flat surfaces. Use the suction cups to grip pieces of material and turn the handle to bring them together.

Handscrew Clamps

Parallel Handscrew Clamps

The matching jaws are ground flat for a firm grip and even pressure when clamping smooth surfaces.

Adjustable-Angle Handscrew Clamps

Each jaw can be positioned at an angle to hold round, angled, and odd-shaped material.

Locating and Support Buttons

Threaded Locating and Support Buttons

Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket.

Press-Fit Locating and Support Buttons

Support and position workpieces and fixtures from the bottom or side. These buttons press into a drilled hole for permanent installation.

Screw-Mount Locating and Support Buttons

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Domed-Head Locating and Support Buttons

Support rounded or irregularly shaped workpieces from the bottom or side with minimal contact.

Swiveling Locating and Support Buttons

The swiveling tip supports uneven and angled surfaces.

Spring-Loaded Guides

Threaded Spring-Loaded Guide Pins

Threading makes these guide pins easier to remove and replace than press fit, so they're useful for high-wear applications.

Spring-Loaded Guide Pins

As the workpiece pushes against the pin head in one direction, the internal spring pushes back to hold it in place for clamping.

Sealed Spring-Loaded Guide Pins

Sealed at the top to prevent debris from getting inside and making them seize up, these guide pins are a good choice for machining fixtures.

Installation Tools for Spring-Loaded Guide Pins

Use these tools for easier guide pin installation.

Create-Your-Own Spring-Loaded Guide Pins

Thread in a screw, handle, or other part to create the right size and shape guide pin for your application.

Spring-Loaded Guide Plungers

As the face of these plungers is pushed in, the internal spring applies outward pressure to hold a workpiece in position against stops and rails.

Spring-Loaded Guide Plungers for Thin Workpieces

Set the tang in a slot below the work surface to prevent thin material from sliding underneath the face.

Locating Pins

Mating Locating Pins and Hole Liners

Maintain consistent alignment in mating parts by installing a pin in one part and a liner in the other.

Locating Pins

Install these pins in a plate or table and mate with holes in a workpiece for precise alignment.

Shoulder-Style Locating Pins

The shoulder provides a consistent height reference point and keeps the pin from being pressed through the fixture.

Removable Locating Pins

A slightly undersized shank makes these pins easy to install and replace. Also known as slip-fit and lock-screw locating pins, they are held in place by a separate lock screw.

Lock Screws for Removable Locating Pins

Secure removable locating pins. The head of the lock screw fits into the notches on the shoulder of the pin.

Threaded Locating Pins

Screw the shank into a threaded hole for quick installation and removal.

Cast-In Locating Pins for Plastics

Encase these pins while molding plastic or composite parts. Once set, the knurls resist movement, letting you align the workpiece with precision on a plate or table.

Air-Powered Locating Pin Retractors

A good choice for automated clamping, these retractors use compressed air to extend and retract a locating pin, protecting the pin from damage in applications where fixtures move through a process, such as along a conveyor belt.

Locating Pin Retractors

Use the handle on these retractors to extend and retract a locating pin, protecting the pin from damage in applications where fixtures move through a process, such as along a conveyor belt.

Floating Locating Pins

The head on these pins slides side-to-side in one direction. Use one of these pins and one standard round-head pin to prevent jamming when loading and unloading workpieces with inconsistent hole spacing.

Slotted Bushings

When locating a workpiece using through-hole alignment pins, use one of these bushings and one standard bushing to prevent the pins from binding in your fixture.

Through-Hole Alignment Pins

Precisely align drilled holes in two parts.

Grippers

Swivel-Tip Gripper Screws

Screw these grippers into place and make quick height adjustments.

Hex-Head Gripper Screws

Make quick height adjustments by turning the threaded stud.

Set-Screw Grippers

Screw in from the top to adjust height or mount from the bottom with a hex key to set the gripping surface flush with the work surface.

Side Grippers

Clamp against these grippers for a secure hold on workpiece edges.

Grippers

Maintain a secure hold on uneven or irregularly shaped parts by clamping against these serrated grippers.

Angled Grippers

The face of these grippers is angled 15°. They can be used in the jaws of lathe chucks.

V-Blocks

Economy V-Blocks

Hold and support round workpieces.

Miniature V-Blocks

Place into larger V-blocks to hold small shafts and cylinders. Sets include two clamps that fit different diameters.

Any-Size V-Blocks

To hold and support large or small round or cylindrical workpieces, position these two-piece V-blocks to accommodate any diameter.

Hardened V-Blocks

Use these pairs of blocks to support long, round workpieces—secure with the built-in clamps.

Magnetic V-Blocks

Magnetic surfaces on the bottom, back, and one V face of these blocks eliminate the need for mounting clamps and bolts.

Adjustable-Angle V-Blocks

Use this block to hold workpieces at precise angles.

Machinable V-Blocks

Easier to machine than hardened steel, these blocks can be customized to fit a workpiece.

Adjustable Supports and Stops

Adjustable Support Screws

When working with large or flexible workpieces that could bow under machining pressure, use these screws as easy-to-install support points. Also known as jack screws or jig screws.

Machine Table Workstops

The T-nut base secures the workstop into the slots of a machine table for positioning parts that extend beyond the jaws of your vise.

Adjustable Side Stops

Adjust the horizontal screw to hold workpieces of varying sizes in precise positions.

Spring-Loaded Work Supports

Slide these low-profile supports under a workpiece to provide support and reduce vibration.

Locating Rails

For locating the side of a workpiece without milling a permanent slot into your fixture, screw these easily repositioned rails into threaded holes.

Fixture Keys

Hole-Mount Fixture Keys

Install these keys in a drilled and reamed hole to locate fixtures and vises on your machine table. Also known as sine keys.

Fixture Keys

Sized to fit with precision in machine table T-slots, use these keys to locate fixtures and vises on your machine table.

Parallels

Sets of Parallels

Sets include multiple sizes of matched pairs that are precision ground for tight tolerances on the top and bottom edges.

Parallels

Place a parallel against each vise jaw to create a rest for your workpiece.

Parallel Keepers

Spring-loaded to keep parallels in place on a vise. Also known as parallel separators.

Adjustable Parallels

Instead of keeping an assortment of parallels on hand, adjust these two-piece tools to your exact height requirements.

Sets of Adjustable Parallels

Adjust these two-piece parallels to your exact height requirements.

Locating and Support Pads

With a larger contact surface than locating and support buttons, these pads can support large workpieces and fixtures. They're also known as rest pads.

Tooling Balls

Adjustable-Height Tooling Balls

Install tooling balls in a workpiece or fixture to create a precise measurement reference point. Push the shank further into the hole to adjust the height of the ball.

Tooling Balls

The shoulder on these tooling balls provides a consistent height reference point.

Tooling Ball Mounting Pads

Use a mounting pad when your tooling ball needs a raised mounting point.

Tooling Ball Covers

Protect tooling balls when not in use.

Pin Punch-Out Blocks

Remove pins from workpieces by positioning the pins over the holes in these hardened steel blocks and tapping them out using a punch and hammer.

Setup Blocks

Use these tight-tolerance blocks as mounting bases and supports to ensure accurate angles and spacing.

High-Precision Index Plungers

To align two parts with more precision than standard spring plungers, these index plungers have a mating bushing that improves alignment and repeatability.

T-Slot Fasteners and Setup Studs

Setup Studs

Combine these setup studs with T-slot nuts, flanged nuts, setup clamps, or setup blocks to clamp and hold workpieces, vises, and other objects onto your fixturing table. Also known as double-ended studs, they have threads on both ends.

Vibration-Resistant Setup Studs

Also known as tap-end and fixture studs, these rods have friction-fit threads on one end to resist loosening and standard threads on the other side for attaching a nut.

T-Slot Nuts

Designed to slide into T-slot tracks on machine tool tables, use these nuts to secure clamps and workpieces.

Secure-Hold T-Slot Nuts

After sliding the nut into a T-slot, tighten the set screw to keep it in place.

Drop-In T-Slot Nuts

Install from the top of the T-slot track and secure with a quarter turn. Also known as quarter-turn T-slot nuts.

T-Slot Nut and Setup Stud Kits

For mounting items to your machine table, these kits contain the full system of necessary components.

T-Slot Bolts

For quicker setups than a separate T-slot nut and stud, slide these bolts into T-slot tracks on machine tool tables.

T-Slot Cleaners

Scrape debris out of machine table T-slots.

T-Slot Covers

Prevent chips, debris, and small parts from falling into T-slots.

Machine Vises

Milling-Machine Vises

Use these vises for reliable workholding on CNC machines.

Adjustable-Angle Milling-Machine Vise Jaws

Arrange the included pins in a series of holes to position a part at any angle and hold odd-shaped parts securely.

Machinable Milling-Machine Vise Jaws

Made from unhardened aluminum or steel, machine these jaws to fit the contours and curves of your workpiece.

Hardened Milling-Machine Vise Jaws

Hardened for wear resistance, these steel jaws are replacements for the ones that come installed on your vise.

Milling-Machine Vise Jaws for Round Material

The V‐shaped recess holds round material securely for machining.

Quick-Change Milling-Machine Vise Jaws

Significantly cut down on jaw changeover time—this two-part system lets you swap out jaws in less than 30 seconds. Mount the jaw plates to the vise and slide the dovetailed jaw stock in and out of the plates.

Slotted Milling-Machine Vise Jaws

Hold workpieces steady with these vise jaws—they work with slot-mount workstops so you can quickly position, adjust, and change out your workpieces.

Milling-Machine Vise Jaws with Changeable Parallels

Quickly move parallels in and out of these jaws to raise your workpiece within the vise. Mount jaws to the vise, slide the mating parallels in place, and rest your workpiece on top.

Repair Kits for Kurt® Milling-Machine Vises

Maintain your vise by replacing seals, springs, and other commonly worn parts.

Swivel Bases for Kurt® Milling-Machine Vises

Mount to a machine table to rotate a vise 360° in 1° increments.

High-Precision Milling-Machine Vises

The vise body and stationary jaw are one piece for high repeatability, even under heavy clamping loads. Ground flat on the base and three sides, these vises ensure accuracy whether mounted on the base, either side, or upright.

Milling-Machine Vise Handle Hangers

Store vise handles near your milling machine.

Milling-Machine Vise Handles

Replace worn, broken, or lost handles.

Compact Milling-Machine Vises

The small size allows multiple vises to be mounted on a single machine table. Frequently used in 4- and 5-axis milling machines, these vises have stepped jaws with serrated teeth that firmly grip just a small portion of your workpiece.

Dovetail Blanks for Dovetail Milling Machine Vises

No need to prepare this material before machining parts in dovetail vises—the dovetails and locating slots are already cut in.

Dovetail Milling-Machine Vises

Designed to hold your part on 4- and 5-axis milling machines, these vises provide rigid clamping while exposing five full sides of the workpiece. This allows even complex parts to be completed in a single operation. You must cut a dovetail into your material before the vise can grip it.

Drill-Press Vises

Turn the handle to move the jaw on these basic vises.

Quick-Clamp Drill-Press Vises

Push the handle to slide the jaw into place for quicker setup than standard drill-press vises.

Any-Orientation Drill-Press Vises

The base and three sides of the vise are ground flat, enabling mounting on its base, either side, or upright.

Cross-Slide Drill-Press Vises

Use the adjustment dials to ensure your work is accurately positioned on X and Y axes.

High-Precision Cross-Slide Drill-Press Vises

The dials on these vises are graduated in smaller increments than standard cross‐slide drill‐press vises for finer adjustment. Use to precisely position work on X and Y axes.

Pivoting-Head Drill-Press Vises

Tilt and lock the vise to hold work at any angle up to 90°.

Any-Angle Machine Vises

Tilt the head on two axes and rotate the base to position your workpiece at almost any angle.

Air-Powered Machine Vises

Compressed air controlled by a foot pedal allows hands‐free operation. Use these vises in production applications with frequent insertion and removal of workpieces.

Machine Vises

Reliably hold workpieces with these basic machine vises.

Self-Centering Machine Vises

The jaws move inward at the same time to consistently position your workpiece in the center of the vise.

Magnetic-Mount Workstops for Machine Vises

Attach these workstops to the side or top of your vise to keep parts in position for machining.

Clamp-On Workstops for Machine Vises

Keep parts in position for machining by mounting these workstops to your vise jaws.

Slot-Mount Workstops for Machine Vises

Mount these workstops into slotted vise jaws—they hold workpieces in place and prevent horizontal movement during machining.

Magnetic Workholding Chucks

To grind, drill, lightly mill, and machine parts that rotate around an axis, these chucks hold parts in place magnetically so you can access their inner and outer diameters.

Magnetic Workholding Plates

The entire surface of these plates is magnetic to provide a powerful hold for grinding, drilling, and electrical discharge machining (EDM). Pull the handle to switch the magnets on and off.

Ultra-Precision Machine Vises

Designed for precision grinding and inspection, the construction of these vises ensures workpieces are held perfectly square. They are also known as toolmakers’ vises.

Vacuum Workholding Plates

Also known as vacuum chucks, these plates secure thin and flexible parts that can’t be held with vises or clamps for milling, drilling, routing, and finishing operations. Connect the system to your shop’s compressed air supply and it's ready to use.

Clamp Workholders

Spring Clamp Workholders

Secure small parts in spring clamps to keep hands free for soldering, gluing, and assembly.

Create-Your-Own Workholders

Build a custom clamping system for holding lightweight objects such as beakers and laboratory equipment.

Bench Vises

Extra-Wide-Opening Tilting-Head Bench Vises

For large workpieces, these vises open three times as wide as standard tilting-head vises. Tilt and lock the head to position work at an angle.

Tilting-Head Bench Vises

The head tilts and locks in place to hold work at an angle.

Any-Angle Tilting-Head Bench Vises

Two vise heads tilt and rotate 360°, locking in place to hold work at any angle.

Rotating-Head Bench Vises

Rotate the head 360° to use three different vise jaws and lock workpieces in position at 45° intervals.

Miniature Bench Vises

Hold tiny workpieces in these compact vises.

Heavy Duty Bench Vises

For big jobs, these vises have a wider jaw opening, deeper throat depth, and larger footprint than standard vises.

Weather-Resistant Bench Vises

Designed for outdoor use, these vises have a finish that resists corrosion.

High-Visibility Bench Vises

A bright yellow vise body stands out on the shop floor.

Stainless Steel Bench Vises for Washdown Applications

Made of 304 stainless steel to stand up to washdown environments, such as food and beverage production, these are the most corrosion-resistant vises we offer.

Bench Vises

Use these vises for general purpose workholding.

Extra-Wide-Opening Bench Vises

The movable jaw can be repositioned to extend the jaw opening. Pull out the entire sliding section and insert it on the opposite side of the vise.

Drop-In Bench Vise Jaw Liners

Insert these one-piece grooved liners between vise jaws to hold small-diameter material vertically.

Wraparound Bench Vise Jaw Liners

Fold the pliable tabs over the jaws to install.

Set-Screw-Mount Bench Vise Jaw Liners

Place over the jaws and tighten the screws to securely attach liners.

Magnetic-Mount Bench Vise Jaw Liners

Choose from flat and grooved liners.

V-Block Magnetic-Mount Bench Vise Jaw Liners

These V-shaped liners hold large round material.

Clamp-On Bench Vises

Quickly install and remove the clamp-on base from a benchtop.

Miniature Clamp-On Bench Vises

Hold your smallest workpieces in these vises, which have a clamp-on base for quick installation and removal from a benchtop.

Tube Holders for Bench Vises

Clamp tubing into these holders to keep it steady while you cut, flare, or expand the end.

Undermount Bench Vises

Also known as woodworkers' vises, these mount to the underside of your workbench and sit flush with the surface.

Bench Vise Jaws

Replace worn flat and V jaws.

Hand-Held Vises

Squeeze-to-Open Hand Vises

Squeeze the body to open the flat jaws; release to grip.

Hand Vises

Jaw are serrated or grooved to firmly grip workpieces.

Nonmarring Hand Vises

Plastic jaw inserts prevent damage to the workpiece.

Hand Vises for Irregularly Shaped Material

Arrange the pins in a series of holes to grip parts with angled or uneven sides.

Hand Vises for Round Material

Notches on the jaws hold round material on its outside diameter.

Chuck-Style Hand Vises

Three chuck-style jaws clamp around your part.

Hollow-Body Pin Vise Sets

Sets include four vises with different opening sizes. A hollow body allows wires and rods to pass through.

Quick-Clamping Hollow-Body Pin Vises

Clamp and unclamp with one hand by sliding the knurled ring forward to close the collet.

Precise-Control Pin Vises

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the vise with your fingertips.

Cushion-Grip Precise-Control Pin Vises

A rubber-covered body provides a comfortable grip. These vises have a rotating end cap on the handle that allows you to apply constant pressure while turning the body of the vise with your fingertips.

Two-Tip Hollow-Body Pin Vises

Each end of the vise has a collet to hold a different tool—turn the collar to close the collets around them.

Hollow-Body Pin Vises

Pass wires and rods through the hollow body of these vises.

Sine Vises

Lift the end of these sine vises by placing gauge blocks underneath—they hold tools and workpieces at precise angles for grinding, cutting, and inspecting.

Circuit Board Vises

A wide opening, large throat depth, and grooved jaws accommodate circuit boards and other flat objects.

Trailer-Hitch Vises

Secure these heavy duty vises to the back of a truck to clamp at your job site.

Swiveling Workholding and Positioning Bases

The attaching end swivels, tilts, and locks into place to position objects. These bases are often used on workbenches and at assembly stations.

Pipe Vises

Nonmarring Bench-Mount Pipe Vises

The jaws are rubber coated to prevent damage to pipe and other round workpieces.

Freestanding Pipe Vises for Clean Rooms

Keep clean rooms free of contaminants. These tripod-mounted vises have rubber-covered jaws that prevent metal-to-metal contact and a plastic-encased chain that seals in lubrication.

Bench-Mount Pipe Vises

Steel jaws secure round workpieces such as pipe, tubing, and conduit.

Freestanding Pipe Vises

Set up the tripod wherever you need to work.

Fixture Plates, Angles, and Tables

T-Slot Fixture Plates

These plates have three T-slots for use with T-slot nuts, bolts, and setup studs.

Grid Fixture Plates

Precision ground to the tightest parallel tolerance, these steel plates have threaded and unthreaded holes in a grid pattern to support precise positioning and repeatability when machining.

Sine Plates

Use the tapped holes to mount your work.

Sine Bars

Measure, mark, and inspect exact angles on dies and other precision parts.

Magnetic Sine Plates

Turn the handle to switch the magnet on and secure steel parts—no need for clamps or screws.

Angle Plates with Mounting Slots

Use these plates to ensure accurate right angles and hold workpieces and fixtures perpendicular to a machine table.

Any-Which-Way Angle Plates

The handle extends the full length and height of these plates for use on any of their six sides.

Angle Plates

Ensure accurate right angles and hold workpieces and fixtures perpendicular to a machine table by securing them to these plates with clamps.

Angle Plates with Mounting Holes

Mount workpieces in precisely located holes for repeatable setups.

Fixturing Tables

Add components such as clamps, brackets, stops, rests, mounting plates, fixturing squares, risers, and V-blocks to build fixtures for welding and assembly.

T-Slot Fixturing Tables

Mount workpiece holders, light machinery, collaborative robots, and other components onto these tables to create custom workspaces, no drilling or tapping required.

Portable Fixturing Tables

Foldable for transport and storage, use these tables as a sturdy work surface for welding, assembly, cutting, and other tasks around your facility.

T-Slot Blocks

Mount these versatile blocks to any flat surface for machine table-style T-slot clamping. They can also be used on a machine table to clamp parts at specific angles or add more total clamping points.

Fixturing Track

Slide 1/4"-20 hex head screws anywhere along the track to create mounting points for clamps and jigs.

Fixturing Squares

Build fixtures on multiple sides of these squares.

Fine-Adjust Cross-Slide Tables

Precisely position work on X- and Y-axes using the handles.

Fine-Adjust Rotary Cross-Slide Tables

Rotate work 360° and precisely position it on X- and Y-axes by turning the handles.

Fine-Adjust Rotary Tables

Rotate your work 360°. These tables can be mounted horizontally or vertically.

Inspection and Measuring Fixturing

Use these components in coordinate measuring machine (CMM) applications to raise a workpiece and reliably position it on a fixture plate with ¼"-20 holes.

Collet Fixtures

Grip and release parts using 5C collets. Use on milling machines, drill presses, or anywhere else you can mount this fixture.

Air-Operated Collet Fixtures

Control clamping action with air. Use 5C collets to grip and release parts on milling machines and drill presses.

Indexing Collet Fixtures

Used with a 5C collet, these fixtures rotate round, hex, or square workpieces up to 1 1/8" diameter in precise increments. Also known as spindexers or punch formers.

High-Density Air/Hydraulic-Operated Collet Fixtures

Use multiple fixtures to create a workholding system capable of clamping and unclamping multiple parts with the push of a button.

Electric Welding Positioners

Mount a workpiece on these motorized turntables for smooth and continuous 360° rotary motion useful for creating circular welds. Turntables tilt and lock in place at angles up to 90° in 15° increments.

Positioning Arms

Bend-and-Stay Positioning Arms

Stronger and with greater load capacities than gooseneck-style positioning arms, these arms keep their shape even when moving or when exposed to vibration. They’re often used in robotics and conveyor applications when frequent repositioning isn’t required.

Heavy Duty Ball-Grip Positioning Arms

With strength for higher load capacities than other ball-grip positioning arms, these arms have a heavy duty construction.

Ball-Grip Positioning Arms

Ball-and-socket connections allow 360° positioning.

Portable Positioning Arms

A suction base makes it easy to move and attach these arms to smooth surfaces such as glass and polished metal.

Miniature Positioning Arms

Position small panels and displays with these compact arms.

Positioning Arms

Heavy Duty Positioning Arms

Heavy duty construction adds strength for higher load capacities than other positioning arms.

Any-Which-Way Positioning Arms

Bend these arms to hold small equipment such as lights and microphones in almost any position.

Threaded Mounting Plates for
Any-Which Way Positioning Arms

Add a mounting surface to an any-which-way positioning arm.

Counterbalancing Positioning Arms

Reduce hand fatigue in continuous fastening and grinding applications. Arms are counterbalanced to support the full weight of the tool as well as absorb torque.

Precision Dimensional Measuring

Rigid-Arm Magnetic-Base Indicator Holders

Fine Adjustment Attachments for
Starrett Magnetic-Base Indicator Holders

Install these attachments onto Starrett magnetic-base holders for more precise control over positioning.

Starrett Rigid-Arm Magnetic-Base Indicator Holders

Economy Rigid-Arm Magnetic-Base Indicator Holders

Jointed-Arm Magnetic-Base Indicator Holders

Economy Jointed-Arm Magnetic-Base Indicator Holders

Flexible-Arm Magnetic-Base Indicator Holders

Adjust the flexible arm to nearly any position.

Low-Profile Magnetic-Base Indicator
Holders with Multiple Mounting Locations

For more versatility than other low-profile holders, this holder has six locations for mounting indicators and accessories, including two mounting holes and four places to mount an indicator lug back with the included thumb screws.

Low-Profile Magnetic-Base Indicator Holders

Use this holder in areas with limited space. It has a nut and bolt for holding a 1/4” lug-back indicator.

Low-Profile Magnetic Base Holders with Positioning Arm

Use a swivel clamp to attach an indicator to the positioning arm.

Rigid-Arm Magnetic-Base Indicator
Holders for Uneven Surfaces

The base is comprised of adjustable magnetic pins which allow it to conform to any shape and grip most metal surfaces.

Economy Magnetic Bases

Flexible-Arm Magnetic-Base Indicator
Holders for Uneven Surfaces

Adjust the flexible arm to nearly any position.

Magnetic Bases

Starrett Magnetic Bases

Jointed-Arm Vacuum-Base Indicator Holders

Position the arm by adjusting joints at the top, middle, and bottom.

Flexible-Arm Vacuum-Base Indicator Holders

Adjust the flexible arm to nearly any position.

Clamp-On Indicator Holders for Bridgeport J Heads

Attach the C-clamp on this holder to your Bridgeport J head to take indicator measurements without obstructing the cutting tool.

Flexible-Arm Weighted-Base Indicator Holders

Adjust the flexible arm to nearly any position.

Clamp-On Indicator Holders

Attach the C-clamp on these holders to your milling machine head to take indicator measurements without obstructing the cutting tool.

Flexible-Arm Clamp-On Indicator Holders

Vise-grip locking pliers clamp these holders to most thin, flat surfaces, and the flexible arm lets you position your indicator around obstructions.

Indicator Swivel Clamps

Secure indicators, upright posts, attachments, and holding rods at any angle.

Attachments for Lever-Style Variance Indicators

Use these attachments to mount indicators in chucks, tool posts, height gauges, or a variety of other setups.

Granite Flat-Surface Plates

Corrosion resistant and nonmagnetic, these smooth plates also resist warping and abrasion.The extremely tight flatness tolerances provide an accurate reference plane for layout and inspection work.

Stands for Granite Flat-Surface Plates

These stands have three plate support points to match the support points on most granite plates.

Flat-Surface Plate Covers

Protect the flatness and finish of plates while in storage.

Lathe Chucks

Three-Jaw Lathe Chucks

Also known as scroll chucks, these are self centering—all three jaws move in unison, centering the workpiece as they close.

Chuck Stops

Consistently position workpieces in a three-jaw lathe chuck by installing a chuck stop. These stops enable short workpieces to extend beyond the chuck's jaws, providing additional clearance.

Machinable Lathe Chuck Jaws

Machine these jaws to fit the curves and edges of your unique workpiece for a tighter hold and more stability than standard hardened jaws.

Hardened Lathe Chuck Jaws

Made from hardened steel, these jaws have a long service life even when performing heavy machining such as roughing cuts.

Lathe Chuck Jaw Nuts

Secure jaws to a CNC lathe chuck with industry standard 1.5 mm × 60° serrations or wider 3 mm × 60° serrations.

Boring Rings for Machinable Lathe Chuck Jaws

Hold machinable lathe chuck jaws in place during machining to make accurate cuts, ensuring the jaws will securely grip your workpiece.

Lathe Mandrels

Expanding-End Lathe Mandrels

An expanding screw widens the end of the mandrel for a tight hold on the inside of a workpiece.

Expanding-End Lathe Mandrel Sets

The mandrels in these sets have an expanding screw that widens the end of the mandrel for a tight hold on the inside of a workpiece.

Wide-Diameter Range Lathe Mandrels

The sleeve on these mandrels expands to hold a range of diameters for better versatility than solid and expanding-end mandrels.

Solid Lathe Mandrels

Use an arbor press to secure the narrow end of one of these tapered mandrels into the hole of a workpiece.

Lathe Centers

Live Centers for Intermittent Use

These light duty centers are for intermittent use on manual lathes.

Live Centers for Continuous Use

A hardened body and point provide the extra strength and wear resistance necessary for continuous use on manual or CNC lathes.

Pipe and Tubing Live Centers

Also known as bull-nose centers, these have a wide head to hold pipe and large-diameter tubing.

Dead Centers

Dead centers are one solid piece. Use them in the headstock when machining between centers or in the tailstock to support the end of a workpiece when friction is not a concern.

Lathe Drivers

Also known as lathe dogs, these drivers connect to a lathe to turn your workpiece when machining between centers. A set screw grips the workpiece while the bent tail connects to the lathe to transmit motion.

Quick-Release Magnetic Brackets

An on/off magnet control makes it easy to move and attach these brackets to metal surfaces.

Mobile Lift Tables

Angled Hand-Crank Mobile Lift Tables

Turn the hand wheels to raise the load and tilt it up to 30° for a more ergonomic angle.

Hand-Crank Mobile Lift Tables

The hand crank on these tables has two speeds for fast and slow adjustment.

Foot-Operated Mobile Lift Tables for Tight Spaces

The top extends beyond the base for easier access to tight spaces and bench tops.

Foot-Operated Mobile Lift Tables

These tables have a foot lever and hydraulic pump to raise loads and either a hand valve or hand lever for controlled lowering.

Long-Tabletop Foot-Operated Mobile Lift Tables

An extra-long, reinforced tabletop gives you plenty of room for oversized loads.

Turntable-Top Foot-Operated Mobile Lift Tables

For easy access to material, the tabletop rotates 360° and locks in any position.

Battery-Powered Mobile Lift Tables

A battery-operated motor and a hydraulic pump do the work for you; they lift loads with the push of a button.

Stationary Lift Tables

Electric Stationary Lift Tables

An electric motor and a hydraulic pump lift loads with the push of a button.

Long-Tabletop Electric Stationary Lift Tables

An extra-large tabletop provides plenty of room for oversized loads.

Turntable-Top Electric Stationary Lift Tables

The turntable rotates to reduce reaching.

Floor-Load Electric Stationary Lift Tables

The tabletop can go as low as 3", making loading and unloading from the floor and pallets easier.

Electric Stationary Lift Tables for Tight Spaces

These tables are compact, yet provide the lifting capacity of standard lift tables.

Foot-Operated Stationary Lift Tables

These tables have a foot lever and hydraulic pump to raise the load.

Air-Powered Stationary Lift Tables

A hydraulic pump and an air-driven motor do the work for you.

Stationary Air-Lift Tables

These tables come ready to operate.

Machine Table Clamps

Step Setup Clamps

Self-Supporting Setup Clamps

Setup Clamps with Threaded Hole

Setup Clamps

Setup Clamp and T-Slot Fastener Kits

Economy Setup Clamp and T-Slot Fastener Kits

Step Blocks

Low-Profile Setup Clamps

Low-Profile Setup Clamps with Threaded Hole

Dual-Clamping Low-Profile Setup Clamps

Nonmarring Setup Clamps

Fingertip Setup Clamps

Setup Clamp Supports

Setup Clamps for Angled Workpieces

Side Clamps

T-Slot Side Clamps

Vise Mounting Clamps

Hold-Down Machine Table Clamps

Machine Table Clamps for Round Workpieces

Fixture Clamps

Fixture Clamps

Machinable Fixture Clamps

Fixture Clamps for Castings and Rough Parts

Low-Profile Fixture Clamps

Machinable Low-Profile Fixture Clamps

Dual-Clamping Fixture Clamps

Machinable Dual-Clamping Fixture Clamps

Hold-Down Fixture Clamps

Threaded Air-Powered Hold-Down Fixture Clamps

Air-Powered Hold-Down Fixture Clamps

Hydraulic-Powered Hold-Down Fixture Clamps

Inside Diameter Fixture Clamps

Inside Diameter Fixture Clampsfor Castings and Rough Parts

Ball-Lock Quick-Change Fixture Clamps

Hold-Down Toggle Clamps

Low-Profile Hold-Down Toggle Clamps

Low-Profile Hold-Down ToggleClamps with Extra Hand Clearance

Heavy Duty Low-Profile Hold-Down Toggle Clamps

Low-Profile Hold-Down ToggleClamps with Locking Handle

Auto-Adjusting Low-Profile Hold-Down Toggle Clamps

Hold-Down Toggle Clamps

Nonreflective Hold-Down Toggle Clamps

Heavy Duty Hold-Down Toggle Clamps

Auto-Adjusting Heavy Duty Hold-Down Toggle Clamps

Hold-Down Toggle Clamps with Locking Handle

Compact Hold-Down Toggle Clamps

Compact Hold-Down ToggleClamps with Locking Handle

Weld-On Side-Mount Hold-Down Toggle Clamps

Side-Mount Hold-Down Toggle Clamps

Rail-Mount Hold-Down Toggle Clamps

Low-Profile Rail-Mount Hold-Down Toggle Clamps

Undermount Hold-Down Toggle Clamps

Dual-Mount Hold-Down Toggle Clamps

Tips for Toggle Clamp Holding Screws

Holding Screws for Toggle Clamps

Dual-Mount Air-Powered Hold-Down Toggle Clamps

Long-Life Dual-Mount Air-PoweredHold-Down Toggle Clamps

Air-Powered Hold-Down Toggle Clamps

Bar-Style Hold-Down Clamps

Drop-In Bar-Style Hold-DownClamps for Workholding Tables

Bench-Mount Bar-Style Hold-Down Clamps

Push/Pull Clamps

Push/Pull Toggle Clamps

Compact Push/Pull Toggle Clamps

Heavy Duty Reverse-Action Push Toggle Clamps

Reverse-Action Push Toggle Clamps

Auto-Adjusting Push Toggle Clamps

Compact Push Toggle Clamps with Locking Handle

Push Toggle Clamps with Locking Handle

Push Toggle Clamps with Rotating Handle

Sealed Push/Pull Toggle Clamps

Hole-Mount Push/Pull Toggle Clamps

Hole-Mount Push/Pull ToggleClamps with Locking Handle

Rail-Mount Push/Pull Toggle Clamps

Hole-Mount Adjustable-Travel Push/Pull Clamps

Adjustable-Travel Push/Pull Clamps

Air-Powered Push Toggle Clamps

Spring Clamps

Miniature Spring Clamps

Inside Diameter Fixture Clamps
for Castings and Rough Parts

Low-Profile Hold-Down Toggle
Clamps with Extra Hand Clearance

Low-Profile Hold-Down Toggle
Clamps with Locking Handle

Compact Hold-Down Toggle
Clamps with Locking Handle

Long-Life Dual-Mount Air-Powered
Hold-Down Toggle Clamps

Drop-In Bar-Style Hold-Down
Clamps for Workholding Tables

Hole-Mount Push/Pull Toggle
Clamps with Locking Handle

Right-Angle Latch-Style Toggle
Clamps with Locking Handle

Nonmarring Swiveling Tips for
Screws and Threaded Studs