Stretch the arm to bring light directly over your work—even across a large surface. Also known as articulating arm lights, these lights have rigid sections that hold their position steady, including when fully extended.

Light up your workspace when overhead lighting falls short.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

Pivot the head to cast a narrow beam of light to exactly where it's needed.

Create a high-intensity lighting system for inspecting small and microscopic parts. With a flexible fiber-optic cable, you can adjust these lights to direct light right where you need it, even in hard-to-reach spots.

Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward.

Illuminate machines or monitor processes in areas where flammable or combustible gases may be present, such as during leaks or ventilation failures. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

Update conventional fluorescent tubular lights with newer LED technology. These lights match the diameter of most older lights and fit existing brackets without the need to drill new mounting holes.

Illuminate machines and monitor processes where flammable and combustible gases, dust, or fibers are present—from paint spray booths to chemical plants. These lights have an enclosure that contains sparks, flashes, and explosions.

Brighten countertops that your ceiling lights can’t reach. These lights are low-profile, so they won’t take up valuable workspace below your cabinets.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Keep excess cords out of your way—the reel locks the cord at any length and retracts it when not in use.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Hang these lights where you need them on the job site.

A series of bulb heads are attached to a power cord to provide overhead lighting for job sites.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Flood hazardous areas with light—these lights are intrinsically safe, meaning they can’t cause an explosion or fire. Rated NEC Class I, II, III, and Zone 0, they’re safe to use in areas with ignitable concentrations of flammable or combustible gases, dust, and fibers.

Safely light up large spaces where combustible gases and dust are normally present. Rated NEC Class I and II, these lights have a housing that contains any sparks or flames and seals out ignitable gases, vapors, and dust.

Bring light to remote areas with the DeWalt rechargeable battery that's already in your toolkit.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Our brightest plug-in floodlights, these lights illuminate large worksites—about the size of a hockey rink.

Light up remote spaces without having to keep track of a new cordless tool battery. These floodlights run on a Milwaukee M18 battery (sold separately). These lights extend up to 7 ft. tall and have a pivoting head to direct light where you need it.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Communicate a status at a glance by wiring these strip lights to change color when a part is malfunctioning inside your enclosure.

For a steady view of fine details even near vibrating machinery, lock each joint on the arm.

Capture the extra-fine details you see under the magnifying lens in a photo or video.