These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Flip these wrenches over to ratchet in the opposite direction.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Suitable for occasional maintenance work, these sets are imported.

These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Suitable for occasional maintenance work, these sets are imported.

Pivot the box end for access to fasteners in tight spots.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

These lightweight tools are also known as AN (Army-Navy) wrenches.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These are also known as tappet wrenches.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

When turning fasteners in small spaces, these short wrenches fit where others can't.

The head is offset 45° to provide additional clearance when reaching over obstructions.

A ratchet mechanism in the heads lets you turn fasteners in tight spaces without removing and repositioning the wrench.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

Made of stainless steel, these wrenches have excellent corrosion resistance.

Fit the narrow head into tight spaces and around thin fasteners.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

The handle is covered in rubber for a comfortable grip.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

No need to pull the socket off the tool—push a button to release.

Bolts and threaded rod pass through these wrenches when used with bolt-through sockets.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

Extend the shaft for additional length.

Position the head anywhere along the handle.

Turn sockets from above when there's not room to swing a standard wrench handle.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

Measure with an accuracy of ±2%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

Anchor these multipliers for added stability.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Use these tools for general shop applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

The handle is covered in plastic for a comfortable grip.

Press the lever to lock the jaw and keep these wrenches clamped on your work, leaving your hands free.

A plastic-covered handle provides a comfortable grip.

These tools have the heavy duty handle and adjustment mechanism of a pipe wrench and the smooth jaws of a traditional adjustable wrench.

Fit the thin head and long jaws into narrow spaces.

Also known as a basin wrench, this tool has a pivoting head and spring-close jaws for working in tight spaces where it’s difficult to adjust a traditional wrench.

Turn fasteners with the firm grip of a wrench and the adjustability of pliers.

Flip the wrench over to use the raised section on the head as a hammer.

Also known as spud, structural, and construction wrenches, the pointed end of the handle aligns bolt holes during assembly.

The handles are covered in plastic for a comfortable grip.

The heads are angled to provide clearance around obstructions.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

The offset head gives you additional clearance to turn hard-to-reach fasteners.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

The long handle provides extra leverage—add an extension to increase it even more.

Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.

The heads are offset to provide clearance for reaching over obstructions.

The heads are offset 45° to provide clearance for reaching over obstructions.

Turn lug bolts on car and truck wheels. These wrenches have a different socket size at each end.

Pivot the socket end to access hard-to-reach fasteners.

Slide the lever to adjust the jaws to fit multiple sizes of square and hex fasteners.