McMaster-Carr logo
    Filter by
    System of Measurement
    Container Type
    Filler Material
    Spool Material
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Industrial Info Compare
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    DFARS Specialty Metals
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    Help me decide (beta)
    29 Products

    Flexible TPU 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. Flexible TPU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Black. Flexible TPU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Blue. Flexible TPU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Green. Flexible TPU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Orange. Flexible TPU 3D Printer Filaments.

    Black

    Blue

    Green

    Orange

    Image of Specification. Front orientation. Contains Border. Red. Flexible TPU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Silver. Flexible TPU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. White. Flexible TPU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Yellow. Flexible TPU 3D Printer Filaments.

    Red

    Silver

    White

    Yellow

    Stretchy, soft, and sturdy, these filaments make durable parts that resist breakage despite repeated use. Stronger than ABS and PLA filaments, they create long-lasting parts, such as seals, sleeves, and gaskets, as well as components that take on high-impact forces, such as springs and snap-fit parts. These filaments don't require a heated printer bed, and they won't shrink or warp when cooling. Use them with a fused filament fabrication (FFF) 3D printer. In general, these flexible filaments require a slow feed rate so they don't jam. The softer your filament, the slower your feed rate will need to be. Store them in a sealed container with a desiccant, or use a dehumidifying cabinet, since ambient humidity will cause the plastic to degrade and weaken.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.
    Conductive—Conductive filaments can be used to create circuit prototypes and other conductive pathways. You can adjust the surface resistivity by changing the temperature of your printer's extruder. As the extruder’s temperature increases, the printed part’s resistivity will decrease.
    Durometer 85A—For the most flexible parts, use durometer 85A filaments. They're more flexible than other TPU filaments.
    Durometer 95A—For a quick print without sacrificing flexibility, choose durometer 95A filaments. They print much faster than other TPU filaments.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Surface
    Resistivity
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Choose a Color
    Each
    TPU Plastic—Durometer 85A (Medium Soft)
    1.75225° to 235° C
    437° to 455° F    		21° to 40° C
    70° to 104° F    		580—44° C
    111° F    		0.25200701,000Opaque Black, Opaque Blue, Opaque Green, Opaque Orange, Opaque Red, Opaque Silver, Opaque White, Semi-Clear White, Opaque Yellow5020N805000000
    2.85225° to 235° C
    437° to 455° F    		21° to 40° C
    70° to 104° F    		580—44° C
    111° F    		0.25200701,000Opaque Black, Opaque Blue, Opaque Green, Opaque Orange, Opaque White5020N80600000
     
    TPU Plastic—Durometer 95A (Medium Soft)
    1.75230° to 240° C
    446° to 464° F    		21° to 40° C
    70° to 104° F    		1,250—49° C
    120° F    		0.25200701,000Opaque Black, Opaque Blue, Opaque Green, Opaque Orange, Opaque Red, Opaque Silver, Opaque White, Semi-Clear White, Opaque Yellow5020N80700000
    2.85230° to 240° C
    446° to 464° F    		21° to 40° C
    70° to 104° F    		1,250—49° C
    120° F    		0.25200701,000Opaque Black, Opaque Blue, Opaque Green, Opaque Orange, Opaque Red, Opaque White, Opaque Yellow5020N80800000
     
    Conductive TPU Plastic—Durometer 60D (Medium)
    1.75220° to 230° C
    428° to 446° F    		45° C
    113° F    		1,7001.5 × 10^3Ω⋅cmNot Rated 0.4200501,000Opaque Black3516N11000000
    2.85220° to 230° C
    428° to 446° F    		45° C
    113° F    		1,7001.5 × 10^3Ω⋅cmNot Rated 0.4200501,000Opaque Black3516N12000000
     

    Impact-Resistant ABS 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. Impact-Resistant ABS 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Black. Impact-Resistant ABS 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Blue. Impact-Resistant ABS 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Gray. Impact-Resistant ABS 3D Printer Filaments.

    Black

    Blue

    Gray

    Image of Specification. Front orientation. Contains Border. Green. Impact-Resistant ABS 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Orange. Impact-Resistant ABS 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Red. Impact-Resistant ABS 3D Printer Filaments.

    Green

    Orange

    Red

    Image of Specification. Front orientation. Contains Border. White. Impact-Resistant ABS 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Yellow. Impact-Resistant ABS 3D Printer Filaments.
    Image of Specification. Front orientation. Beige. Impact-Resistant ABS 3D Printer Filaments.

    White

    Yellow

    Beige

    Bumps, scrapes, and falls won’t damage these tough ABS filaments. Known for their durability, they absorb impact without cracking or breaking, and won’t degrade when heated. Use them to print tool handles, storage cases, and other parts that are handled or dropped frequently. These filaments are a good place to start if you’re experimenting with printing impact-resistant parts.
    Use with a fused filament fabrication (FFF) 3D printer. These filaments have a high melting point and must be printed onto a heated bed. Without it, parts will cool too quickly and warp. These filaments also release fumes as they are printed, so use an enclosed printer or a fume exhauster to ventilate them.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.
    Carbon Fiber Filled—Carbon-fiber-filled ABS filaments make rigid parts that are difficult to bend and break. Their parts can also be threaded and machined more easily than ABS filaments without a filler. Carbon-fiber-filled filaments are abrasive, so you should use them with an abrasion-resistant nozzle. They will wear out other nozzles.
    Fiberglass Filled—Fiberglass-filled ABS filaments make parts that are stronger and less likely to warp or shrink than ABS filaments without a filler. Fiberglass-filled filaments are abrasive, so you should use them with an abrasion-resistant nozzle. They will wear out other nozzles.
    ABS/Polycarbonate—For heavy impact, use ABS/polycarbonate filaments. The polycarbonate adds strength to printed parts.
    UL 94 V-0—Filaments rated UL 94 V-0 meet strict flammability standards. Use them to create holders, guards, housings, and other parts that protect sensitive, flammable equipment and machinery.
    Static Dissipative—Static-dissipative filaments make parts that protect equipment from electrostatic shocks by diverting electrostatic discharges in a controlled way. Use them to create tool handles, tote trays, enclosures, and other parts that are used near sensitive electronics. To adjust the surface resistivity of your printed part, change the temperature of your printer’s extruder. As the extruder’s temperature increases, the printed part’s resistivity will decrease.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Surface Resistivity,
    ohm/sq.
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Choose a Color
    Each
    ABS
    1.75220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		6,090—90° C
    194° F    		0.25195751,000Black, Blue, Gray, Green, Orange, Red, White, Yellow, Beige1317N537000000
    2.85220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		6,090—90° C
    194° F    		0.25195751,000Black, Gray, White1317N53800000
     
    Carbon Fiber-Filled ABS
    1.75220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		6,670—76° C
    169° F    		0.419555750Black1317N31100000
    2.85220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		6,670—76° C
    169° F    		0.419555750Black1317N31200000
     
    Fiberglass-Filled ABS
    1.75230° to 245° C
    446° to 473° F    		95° to 110° C
    203° to 230° F    		9,862—89° C
    192° C    		0.419862750Black1317N41500000
     
    ABS—Static Dissipative
    1.75220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		8,4101× 10^7 to 1× 10^997° C
    207° F    		0.420075750Black3481N1300000
    2.85220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		8,4101× 10^7 to 1× 10^997° C
    207° F    		0.420075750Black3481N1400000
     
    ABS—UL 94 V-0
    1.75220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		6,520—95° C
    203° F    		0.420075750Black3665N41100000
    2.85220° to 240° C
    428° to 464° F    		100° to 110° C
    212° to 230° F    		6,520—95° C
    203° F    		0.420075750Black3665N41200000
     
    ABS/Polycarbonate—UL 94 V-0
    1.75265° to 285° C
    509° to 545° F    		110° to 120° C
    230° to 248° F    		8,700—125° C
    257° F    		0.420075750Black3665N1500000
     

    UV- and Impact-Resistant ASA 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. UV- and Impact-Resistant ASA 3D Printer Filaments .
    Image of Specification. Front orientation. Contains Border. Black. UV- and Impact-Resistant ASA 3D Printer Filaments .

    Black

    Image of Specification. Front orientation. Contains Border. Blue. UV- and Impact-Resistant ASA 3D Printer Filaments .

    Blue

    Image of Specification. Front orientation. Contains Border. Gray. UV- and Impact-Resistant ASA 3D Printer Filaments .

    Gray

    Image of Specification. Front orientation. Contains Border. White. UV- and Impact-Resistant ASA 3D Printer Filaments .

    White

    Best for outdoor use, parts made from these ASA filaments are UV resistant, so they won't warp or crack from prolonged sun exposure. They’re also durable, so they absorb impact without breaking and won’t degrade when heated.
    Use with fused filament fabrication (FFF) 3D printer. These filaments have a high melting point and must be printed onto a heated bed. Without it, parts will cool too quickly and warp. These filaments also release fumes as they are printed, so use an enclosed printer or a fume exhauster to ventilate them.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Choose a Color
    Each
    ASA
    1.75235° to 255° C
    455° to 491° F    		90° to 110° C
    194° to 230° F    		6,52095° C
    203° F    		0.4200751,000Black, Blue, Gray, White1317N541000000
    2.85235° to 255° C
    455° to 491° F    		90° to 110° C
    194° to 230° F    		6,52087° C
    188° F    		0.4198781,000Black1317N55200000
     

    Chemical-Resistant PPSU 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. Chemical-Resistant PPSU 3D Printer Filaments.
    Image of Specification. Front orientation. Contains Border. Off-White. Chemical-Resistant PPSU 3D Printer Filaments.

    Off-White

    Fabricate custom bottles, packaging, and other parts for chemical processing. Made of PPSU, these filaments won’t break down even after prolonged exposure to virtually any acid, base, or solvent. They also stand up to oil and fuel, so they’re sometimes made into automotive parts. Because they have a low density and won’t transfer electricity, they make parts that are lightweight and protect components from electric currents. These filaments are easy to store too, since they resist absorbing water. Rated UL 94 V-0, they meet flammability standards.
    Print these filaments on a fused filament fabrication (FFF) 3D printer. Due to its high melting point, PPSU is more difficult to print than most other materials. You need an all-metal extruder and a heated printer bed to reach its minimum printing temperature. After printing, anneal your part in an oven for 2 to 4 hours to reach its maximum strength, temperature, and ability to resist chemicals.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your part will start to lose structural integrity.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Annealing
    Temp.
    Max. Exposure
    Temp.
    Flammability
    Rating
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Each
    PPSU
     
    Off-White
    1.75390° to 410° C
    734° to 770° F    		140° to 160° C
    284° to 320° F    		7,97080° to 130° C
    176° to 266° F    		180° C
    200° C    		UL 94 V-0
    		0.4200405004271N70000000
     

    High-Strength Impact-Resistant Polycarbonate 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. High-Strength Impact-Resistant Polycarbonate 3D Printer Filaments .
    Create strong, durable parts that carry heavy loads and absorb blows and other impact without cracking or breaking. Made of polycarbonate, these filaments are stronger and resist heat better than other impact-resistant filaments, such as those made from ABS or ASA.
    Use with a fused filament fabrication (FFF) 3D printer. These filaments have a high melting point and must be printed onto a heated bed. Without it, parts will cool too quickly and warp. These filaments also release fumes as they are printed, so use an enclosed printer or a fume exhauster to ventilate them.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.
    Carbon Fiber Filled—Carbon-fiber-filled polycarbonate filaments make rigid parts that are difficult to bend and break. Parts made from these filaments can also be threaded and machined more easily than parts made from polycarbonate filaments without a filler. Carbon-fiber-filled filaments are abrasive, so you should use them with an abrasion-resistant nozzle.
    Static Dissipative—Static-dissipative filaments make parts that protect equipment from electrostatic shocks by diverting electrostatic discharges in a controlled way. Use them to create tool handles, tote trays, enclosures, and other parts that are used near sensitive electronics. To adjust the surface resistivity of your printed part, change the temperature of your printer’s extruder. As the extruder’s temperature increases, the printed part’s resistivity will decrease.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Surface Resistivity,
    ohm/sq.
    Hardness
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Color
    Each
    Polycarbonate
    1.75280° to 310° C
    536° to 590° F    		110° to 120° C
    230° to 248° F    		8,990—Durometer 84D
    (Hard)    		135° C
    275° F    		0.419540500Black1317N322000000
     
    Carbon Fiber-Filled Polycarbonate
    1.75260° to 280° C
    500° to 535° F    		80° to 100° C
    175° to 210° F    		10,580—Not Rated 115° C
    245° F    		0.419555750Black1317N35300000
    2.85260° to 280° C
    500° to 535° F    		80° to 100° C
    175° to 210° F    		10,580—Not Rated 115° C
    245° F    		0.419555750Black1317N35400000
     
    Polycarbonate—Static Dissipative
    1.75260° to 300° C
    500° to 572° F    		110° to 120° C
    230° to 248° F    		9,8601× 10^7 to 1× 10^9Rockwell R125
    (Hard)    		135° C
    275° F    		0.420075750Black3481N15000000
     

    Wear-Resistant Nylon 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. Wear-Resistant Nylon 3D Printer Filaments .
    Image of Specification. Front orientation. Contains Border. Black. Wear-Resistant Nylon 3D Printer Filaments .

    Black

    Print tough, long-lasting parts that won’t scratch or wear out from constant motion and friction, such as gears and washers. You can even tap or drill the parts without them cracking or shattering.
    Use these filaments with fused filament fabrication (FFF) printers. Because of their relatively high melting point, a heated printer bed is recommended. These filaments also emit fumes when printing, so it’s best to use them in an enclosed printer or to remove the fumes with a fume exhauster. Store them in a sealed container with a desiccant so they don’t absorb moisture in the air, which can make them unusable.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.
    Carbon Fiber Filled—Carbon-fiber-filled nylon filaments make rigid parts that are difficult to bend and break. Their parts can also be threaded and machined more easily than the same filaments without any filler. However, they’re abrasive, so only use them with abrasion-resistant nozzles.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Hardness
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Each
    Carbon Fiber-Filled Nylon
     
    Black
    1.75280° to 300° C
    535° to 570° F    		50° C
    122° F    		15,225Not Rated 215° C
    419° F    		0.4200655003483N6000000
     

    Foam-Forming 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. Foam-Forming 3D Printer Filaments .
    Print these polypropylene filaments into filters, gaskets, and other lightweight, foam-like parts that let air and gas pass through but repel water. They contain a filler that dissolves in water, forming hollow spaces that make up 45% of the part. Polypropylene is known for being rigid yet flexible, so it absorbs impacts and bounces back to shape after bending, making these filaments good for compressible seals and living hinges. It also resists hydrocholoric and phosphoric acids, as well as other nonoxidizing acids and bases.
    These filaments work with fused filament fabrication (FFF) 3D printers. If using a glass print surface, apply an adhesive to prevent the filament from detaching. The recommended print speed is 25 mm/s. While polypropylene is likely to shrink, the filler in these filaments supports your design, preventing it from losing shape as it prints. Submerge your part in hot water for about 24 hours after printing to dissolve the filler and expose the pores.
    For extra support when printing complex designs, use structural support 3D printer filaments. They dissolve in water at the same time as this filament’s filler.
    Spool
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Hardness
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.,
    mm
    Dp.,
    mm
    Material
    Wt.,
    g
    Each
    Polypropylene
     
    Opaque White
    1.75190° to 240° C
    374° to 464° F    		95° to 125° C
    203° to 257° F    		1,000Durometer 90A
    (Medium Soft)    		140° C
    284° F    		0.420055Plastic5004275N110000000
    2.85190° to 240° C
    374° to 464° F    		95° to 125° C
    203° to 257° F    		1,000Durometer 90A
    (Medium Soft)    		140° C
    284° F    		0.420055Plastic5004275N12000000
     

    Moisture-Resistant Polyester 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. Moisture-Resistant Polyester 3D Printer Filaments .
    Image of Specification. Front orientation. Contains Border. Clear. Moisture-Resistant Polyester 3D Printer Filaments .

    Clear

    Parts printed with these polyester filaments absorb less moisture than other types of plastic, making them ideal for use in wet or humid environments. They are more durable and flexible than PLA, and easier to print than ABS. Use these filaments with fused filament fabrication (FFF) 3D printers, and print onto a heated print bed. Printing onto a cool surface causes the molten filament to change temperature rapidly, which can warp your designs. Although finished parts are moisture-resistant, these filaments are sensitive to humidity, and should be stored in a dehumidifying cabinet or a sealed container with desiccant for the best printing quality.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.
    PCTG—PCTG is more impact resistant than PETG and holds up to a wide range of acids and bases without breaking down. It is often used for printing parts that will be exposed to chemicals and oils.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Hardness
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Each
    PCTG
     
    Clear
    1.75250° to 270° C
    482° to 518° F    		70° to 80° C
    158° to 176° F    		5,510Not Rated 70° C
    158° F    		0.25200681,0003462N511000000
    2.85250° to 270° C
    482° to 518° F    		70° to 80° C
    158° to 176° F    		5,510Not Rated 70° C
    158° F    		0.25200681,0003462N51200000
     

    Dremel 3D Printer Filaments

    Image of Product. Front orientation. 3D Printer Filaments. Dremel 3D Printer Filaments .
    Build parts and prototypes from these filaments using Dremel fused filament fabrication (FFF) 3D printers. An RFID tag on the spool communicates with your printer, automatically adjusting it to the correct temperature and print speed for the filament material and notifying you when the filament is running out.
    Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.
    NylonAbout Nylon
    Image of Specification. Front orientation. Contains Border. Black. Dremel 3D Printer Filaments .

    Black

    Nylon resists scratches and wear, and is often used to create parts that encounter constant friction such as gears or bearings. Nylon parts also won’t crack or shatter when they’re drilled or tapped. Exposure to humidity makes these filaments brittle and unusable, so they need to be stored in a sealed container with a desiccant. Like ECO-ABS, parts can warp during cooling and need a heated printer bed. Make sure your printer is connected to a ventilation system, as nylon emits fumes during printing.
    Tensile Strength—Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.
    Spool,
    mm
    Mfr. Model
    No.
    Dia.,
    mm
    Printing Temp.
    For Printer
    Bed Temp.
    Tensile Strength,
    psi
    Max. Exposure
    Temp.
    For Min. Nozzle
    Opening Dia., mm
    Dia.
    Dp.
    Wt.,
    g
    Color
    Each
    DF45-NYP-B1.75230° to 250° C
    446° to 482° F    		80° C
    176° F    		7,540155° C
    311° F    		0.418055500Black3653N12000000
    back to top