Manufacturer Manufacturer | Show |
|---|
|
Manufacturer Manufacturer | Hide |
|---|
|
|
Manufacturer Model Number Manufacturer Model Number |
|---|
|
Duty Cycle Duty Cycle |
|---|
|
Cord Length Cord Length |
|---|
|
For Cartridge Size For Cartridge Size |
|---|
|
|
|
Applicator Type Applicator Type |
|---|
|
Temperature Setting Temperature Setting |
|---|
|
Plug Type Plug Type |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Opening ID Opening ID |
|---|
|
|
Adhesive Output Adhesive Output |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
3M Hot-Melt Glue Guns
Dispense 3M hot-melt adhesives with these guns. Guns include one tip.
For Glue Stick | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Manufacturer Model No. | Dia. | Lg. | For 3M Glue Stick Model No. | Wattage, W | Voltage | Temp. Setting, °F | Adhesive Output, lbs./hr. | Duty Cycle | Warm-Up Time, min. | Cord Lg., ft. | Includes | Each | |
| AE II | 1/2" | 10" | 3750 | 250 | 120V AC | 400° | 4 | Continuous | 3 | 8 | 3/32" Diameter Tip | 0000000 | 0000000 |
Nozzles for 3M Hot-Melt Glue Guns
Use L-tips to close full-overlap cartons.
T-tips dispense two lines of glue to close slotted cartons.
Tips are not compatible with model AE II or AE II LT glue guns.
Adjustable-Temperature 3M Hot-Melt Glue Guns
With five temperature range options, these guns can dispense 3M adhesives with different melting points. Install the temperature module that matches the application temperature of your 3M glue stick. Gun has a stroke adjuster that controls the amount of adhesive dispensed per trigger squeeze. One tip is included; additional tips are sold separately.
For Glue Stick | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Manufacturer Model No. | Dia. | Lg. | For 3M Glue Stick Model No. | Wattage, W | Voltage | Temp. Setting, °F | Adhesive Output, lbs./hr. | Duty Cycle | Warm-Up Time, min. | Cord Lg., ft. | Includes | Each | |
| EC | 5/8" | 8" | 3738, 3762, 3762LM, 3764, 3789, 3792, 3792LM | 350 | 120V AC | 262° to 283° 288° to 312° 356° to 379° 390° to 416° 417° to 450° | 5.5 | Continuous | 10 | 8 | 3/32" Diameter Tip, Stroke Adjuster | 0000000 | 0000000 |
Use L-tips to close full-overlap cartons.
T-tips dispense two lines of glue to close slotted cartons.
Swap out worn or broken parts for your 3M hot-melt glue gun.
3M Hot-Melt Glue Gun Repair Parts
Swap out worn or broken parts for your 3M hot-melt glue gun.
Electric/Air-Powered 3M Hot-Melt Glue Guns
For use in high-volume production applications, these guns use electric heat to melt the adhesive and compressed air to keep it flowing. Load up to three glue sticks at once. The gun includes one tip; additional tips are sold separately. Use only with 3M glue sticks.
For Glue Stick | Air Inlet | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Manufacturer Model No. | Dia. | Lg. | For 3M Glue Stick Model No. | Wattage, W | Voltage | Temp. Setting, °F | Adhesive Output, lbs./hr. | Duty Cycle | Warm-Up Time, min. | Operating Air Pressure, psi | Pipe Size | Thread Type | Gender | Air Hose Lg., ft. | Cord Lg., ft. | Each | |
| II | 1" | 3" | 3738, 3762 | 500 | 120V AC | 385° | 7.5 | Continuous | 15 | 50-80 | 1/8 | NPT | Male | 8 | 8 | 00000000 | 000000000 |
Use L-tips to close full-overlap cartons.
T-tips dispense two lines of glue to close slotted cartons.
3M Two-Part Adhesive Dispensing Guns
Use these guns to dispense two-part adhesives. Use them only with 3M dual cartridges.
The gun for 6.76-oz. cartridges is suitable for high-volume applications.
Air-Powered 3M Two-Part Adhesive Dispensing Guns
Mixer Nozzles for Two-Part Adhesive Cartridges
To simultaneously mix and dispense two-part adhesives, attach these mixer nozzles to a dual cartridge. Mixing elements help combine the two parts of an adhesive as it flows through the nozzle. A short nozzle with many mixing elements combines adhesive while minimizing the adhesive left in the nozzle after dispensing. Choose a nozzle that matches the connection type, size, and mix ratio of your adhesive cartridge.
A taper tip has a small opening for controlled dispensing.
A step tip allows you to trim the opening to the diameter you need.
