Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These short sockets fit spaces where height clearance is limited.

Hold fasteners securely in place as you drive them.

Designed for use with stainless steel fasteners, these sockets are more corrosion resistant than steel sockets and less likely to flake.

Pair these sockets with a bolt-through ratchet wrench to reach nuts at the bottom of a long threaded rod or bolt which can pass through the socket and the head of the wrench.

Pivot the head to access fasteners from an angle.

The short bit on these sockets fits in spaces where height clearance is limited.

When vertical space is tight or you need an extra twist on your socket, use these dual drive hex bit sockets. They work with a standard square drive tool and a box or open end wrench.

Extra-long bits allow access to hard-to-reach fasteners.

Reach nuts obstructed by a fluid line or other barrier with these wrench heads.

Attach one of these heads to your square-drive ratchet or torque wrench to extend its reach or to access spaces with limited vertical clearance.

Pivot the head to access fasteners from an angle.

Move from lug nut to lug nut with the speed of a racecar pit crew. Up to five standard 6-point lug nuts stack up in the shank of these sockets, so you don’t have to stop to take the lug nuts out of the socket.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Extra length allows access to fasteners on long bolts.

Attach these sockets to your spline-drive impact wrench.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These sockets are made to withstand the high torque and force of impact tools.

The short bit on these sockets fits in spaces where height clearance is limited.

Designed to remove and install dual wheels on trucks and trailers, these sockets have a hex recess for accessing lug nuts and a square recess to turn the threaded shafts found on inner wheels.

A magnet holds the fastener securely enough to drive self-tapping screws.

Suitable for occasional maintenance work, these sets are imported.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Two spring-loaded balls inside these sockets firmly hold nuts and bolts in place as you turn them, including nonmagnetic fasteners like stainless steel screws.

With more than double the clearance of standard sockets, the sockets in these sets access nuts on extra-long bolts.

Suitable for occasional maintenance work, these sets are imported.

Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.

Extra-long bits allow access to hard-to-reach fasteners.

A spring-loaded ball on the bit holds fasteners in place as you drive them, including nonmagnetic fasteners like stainless steel screws.

In addition to a standard square drive, the sockets in these sets have a hex-shaped base so you can use a ratchet wrench along with an open-end or box wrench for additional leverage.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Reach nuts obstructed by a fluid line or other barrier with the wrench heads in these sets.

Get a strong grip in tight areas, even on fasteners that are rounded or damaged.

Tighten or loosen nuts and bolts without damaging the finish.

Carry fewer impact sockets—these five reversible impact sockets turn 10 fastener sizes. Flip the socket around to turn a different size.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Pivot the head to access fasteners from an angle.

Convert your standard 6-point sockets into hex bit sockets with these bits.

Tighten or loosen fasteners with a socket or bit—these tools have a magnet for attaching both.

Turn nuts on bolts and threaded rods, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.

Tap components into alignment before fastening.