Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

A static-dissipative coating on this polyester film prevents electrostatic discharge from damaging sensitive electronic equipment.

Also known as frisket film, this polypropylene has a low-tack adhesive that releases without leaving residue behind.

Made from FDA-listed materials for use with food.

Made of FDA-listed materials, these sheets and strips are for use with food.

Filled with carbon black, these sheets won’t generate static charges and divert existing ones away from electronics. Use them as a conductor to protect components from static discharge.

One layer of fiberglass cloth is inserted between two layers of silicone rubber to give these sheets and strips the strength to stand up to high stress and flex. Use them as flange gaskets and anywhere heavy compression would squeeze nonreinforced silicone rubber out of place.

Made from FDA-listed materials for use with food and beverage, these EPDM sheets and strips can be used in steamy environments.

Buna-N rubber resists fuel oil, hydraulic oil, ethylene glycol, and grease.

With the greatest tensile strength of all our oil-resistant rubber, these super-strong Buna-N sheets and strips can handle high-tension applications, such as belting.

Keep frequently touched elevator panels, kiosks, counters, and other large surfaces free of germs.

Wrap fingers to protect against cuts and abrasions without limiting dexterity.

For outdoor painting jobs, this plastic tape stands up to the elements. The high-tack adhesive works on rough exterior surfaces, such as stucco and masonry.

Use this solvent-resistant plastic tape for anodizing and electroplating applications.

Cover holes, fastener heads, and small areas with these shapes.

Use these convenient cut shapes to mask holes, fastener heads, and small areas while soldering.

Made of polyester plastic, this tape resists tearing in high-temperature masking jobs, such as on circuit boards and when powder coating.

Temporarily protect highly polished plastic, metal, and glass surfaces from scratching and marring.

This tape reflects intense heat to protect sensitive components.

Made to the highest standards for cleanliness, this tape meets clean room requirements. It releases minimal contaminants, leaves no residue behind, and comes sealed in a plastic bag. Use it to mark hazardous items or areas.

Outline and draw attention to safety zones and hazards with this tape.

Seal out light to mask LEDs and prevent backlight bleed on LCD monitors with this opaque polyester tape.

Providing all-weather corrosion protection, this vinyl tape resists salt water, UV light, acids, and alkalies. Use it to wrap pipes and electrical conduit both above and below ground.

Use this UV-resistant tape to temporarily protect smooth plastic, metal, and glass surfaces.

Highly resistant to impact, tearing, and corrosive chemicals, use FEP tape to line chutes and hoppers and to cover shelves in laboratories.

Add a slippery surface to difficult-to-bond surfaces, such as plastic, foam, and powder-coated metal.

Our most slippery tape, the slick surface allows items to glide smoothly over it.

A strong, thick layer of Teflon® PTFE makes this tape tougher than standard Low-Friction Tape Made with Teflon® PTFE.

Cover chutes, packaging lines, and slides with this tape for a slippery, nonstick surface that resists abrasion and impact.

PEEK offers the best wear and abrasion resistance of our low-friction tapes. Use it for wire wraps and sliding bearing surfaces.

At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.

This polyester tape has a woven mesh edge that conducts electricity. Use it to shield cables and electronic components from EMI (electromagnetic interference).

This chemical-resistant tape has adhesive on both sides.

Insulate wire and cable splices, wrap wire harnesses, and repair cable jacketing with this stretchy tape.