Greater strength than standard High-Temperature Silicone translates into better shock-absorbing qualities and longer life.

Create a barrier against fire and smoke. These sheets and strips meet FAR 25.856 and UL 94 V-0 for flame retardance.

Made from FDA-listed materials for use with food.

While other black rubber can leave a mark after use, these specially formulated neoprene sheets leave no evidence behind.

With one layer of nylon fabric for every 1/16” of thickness, these sheets have the strength to be used as flange gaskets, diaphragm packing, and anywhere heavy compression would squeeze nonreinforced neoprene out of place.

Even after repetitive compression, these super-soft sheets and strips maintain their cushioning ability. Use them to dampen noise and isolate vibration.

With one layer of polyester fabric for every 1/16” of thickness, these sheets and strips maintain their size and shape under heavy compression better than the nonreinforced abrasion-resistant SBR.

With greater strength than standard Weather-Resistant EPDM, these sheets and strips provide better shock-absorbing qualities and longer life.

Often used as inner tubes, butyl rubber won’t allow air, fumes, or gases to pass through.

Buna-N rubber resists fuel oil, hydraulic oil, ethylene glycol, and grease.

Because these sheets and strips are made from peroxide-cured Buna-N rubber, they have better heat resistance than standard Oil-Resistant Buna-N rubber sheets and strips.

Viton® fluoroelastomer stands up to tough chemicals, such as nitric acid, ethylene glycol, and isopropyl alcohol.

Use these clear sheets for strong, invisible bonds.

These foam discs and squares have extra-strong adhesive on both sides to create permanent bonds.

Tape is cut into convenient discs and rectangles.

Protect small parts with these slippery UHMW rings, discs, and squares.

Low-Friction Tape Shapes Made with Teflon® PTFE.

Use these convenient cut shapes to mask holes, fastener heads, and small areas while soldering.

Also known as mastic tape, this tape is thicker than other electrical tape to cushion, insulate, and seal out moisture and environmental contaminants in electrical connections.

These magnets are made of corrosion-resistant ceramic and bonded with rubber for flexibility.

Stretch these magnetic strips over corners and irregular surfaces.

These sheets and strips will bounce back to shape, even after extended compression.

One layer of fiberglass fabric is sandwiched between layers of silicone foam giving these strips strength to handle high-stress applications, such as gasketing.

Prevent the spread of flames with these self-extinguishing silicone foam sheets and strips.

Seal and damp vibration around high-temperature food-service equipment with these silicone foam sheets and strips.

Made of a blend of neoprene and EDPM, these foam sheets and strips resist water, sunlight, and oxidation.

These vinyl foam sheets and strips are so conformable that once they're compressed they won't fully spring back. Use them to fill gaps and seal uneven surfaces.

Because this natural rubber foam readily bounces back to shape after compression, it’s a good choice for repetitive sealing applications, such as on doors.

Durable enough to be used in seat cushions, this flexible polyurethane foam provides gentle cushioning support.

Good for tough vacuum-sealing and low closure-force applications, these polyurethane foam sheets and strips have open/closed cells to keep water, air, and gases from being absorbed when they are compressed at least 25%. Even after extended compression, all bounce back to shape faster than other foams we offer.

Often used for impact pads, gaskets, and enclosure seals, these polyurethane foam sheets and strips absorb shock better than other resilient foam.

These sheets and strips are made of cross-linked polyethylene, so they are stronger and more chemical resistant than other types of polyethylene foam.

This foam meets UL fire extinguishing specifications. It's made from a blend of Buna-N, neoprene, and vinyl to offer offer good resistance to oil.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

Kapton® polyimide film is an excellent electrical insulator.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

A static-dissipative coating on this polyester film prevents electrostatic discharge from damaging sensitive electronic equipment.

Also known as frisket film, this polypropylene has a low-tack adhesive that releases without leaving residue behind.

This synthetic felt is an economical alternative to wool felt.

Inherently sticky, this silicone gel material conforms to irregular surfaces and stays in place for an effective moisture barrier.

Because this expanded PTFE tape is thicker than other gasket tape, it fills the irregularities on rough-surfaces flanges when compressed for a tight seal.

Stick these gaskets around door and vent cutouts or replace worn seals to maintain your enclosure's NEMA rating.

Made of 1000 series aluminum which is 99% pure, this aluminum offers superior formability, corrosion resistance, and electrical conductivity. It's frequently fabricated into raceways, decorative trim, and other parts where strength and hardness are not required.

Apply this general purpose tape to any surface that requires traction.

Stick this ultra-flexible tape to ladder rungs, diamond tread plates, and other uneven and irregular surfaces with sharp corners.

Make stairs, ramps, and walkways safer with this eye-catching, high-traction tape.

With its reflective, mirror-like finish, this film is often used to repair or create new decorative finishes on edge trim, panels, and other flat surfaces.

Often used to protect sheet metal during fiber and CO2 laser cutting, this film is also good for other fabrication processes such as bending, stamping, and forming. You can even leave this film on finished parts for protection against damage during shipping and storage.

Made of woven polyethylene fabric, this is the most puncture-, abrasion-, and tear-resistant surface protection we offer. Commonly used on heavy equipment, it guards metal, plastic, composite, and painted surfaces from damage. It can also be used as a protective layer beneath other materials.

Keep windows from producing flying glass if they break.

These sheets have a long-lasting diamond abrasive.

Cut the length you need, then stick to your sanding tool. When it's time to change the sheet, peel it off.

Peel and stick to your sanding tool. When it’s time to change the sheet, peel it off.

A urethane coating protects these humidity-resistant polyurethane foam sheets from oil exposure. Use them to quiet noisy areas and line machine enclosures.

Use these sheets to quiet noisy areas and line machine enclosures. They’re made of humidity-resistant polyurethane foam and have a smooth, easy-to-clean facing.

Reflect sound and block noise from traveling to other parts of your facility.

The nonglare dry erase surface on these sheets doubles as a projection screen.

Cut with scissors to create a custom-size sheet.