For Cutting For Cutting |
|---|
|
|
For Wire Type For Wire Type |
|---|
|
For Use On For Use On |
|---|
Component Component |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Required Handle Required Handle |
|---|
|
Cutting Force Cutting Force |
|---|
|
Cutting Pattern Cutting Pattern |
|---|
|
Air Pressure Air Pressure |
|---|
|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Powered Nibblers and Powered Cutters
More
Air-Powered Wire Cutters
Good for high-volume cutting and trimming.
Handles have a safety lever that prevents accidental operation; push the thumb latch forward to activate.
Jaws can be mounted in the handle for left- or right-hand use.
Style D jaws allow precise cutting from above. Pointed-cut jaws cut and crimp in one action.
Cut profile refers to the amount of pinch left on the tip of the wire after it has been cut. Pointed cutters produce a deeply pointed, pinched end. Use for electrical and general applications. Semiflush cutters are the most widely used for electronics assembly and produce a slightly pointed, pinched end. They are generally more accurate than pointed-cut tools. Flush cutters produce a cut with virtually no pinch, creating clean connections for easy soldering. Flush-cut tools don’t last as long as pointed and semiflush.
Air Inlet | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Style | Component | Cutting Force | Lg. | OD | Wt., oz. | Pipe Size | Gender | Recommended Operating Air Pressure, psi | Includes | Material | Each | |
| A | Standard Handle | 850 lbs. @ 80 psi | 5 1/2" | 1 3/4" | 13 | 1/8 | Female | 60-100 | 5 ft. Lg. 1/8 NPT Male × 1/4 NPT Male Air Hose | Aluminum | 00000000 | 0000000 |
| B | High-Force Handle | 1,120 lbs. @ 80 psi | 4" | 1 3/4" | 16 | 1/8 | Female | 60-100 | 5 ft. Lg. 1/8 NPT Male × 1/4 NPT Male Air Hose | Aluminum | 00000000 | 000000 |
For Wire | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Style | Required Handle | Lg. | Cut Profile | Cutting Edge Location | Jaw Lg. | Max. Dia. | Max. Gauge | Type | Material | Finish | Each | |
| C | Standard | 2 1/2" | Semiflush | Side | 1/2" | 0.091" | 11 | Soft Wire | Steel | Black Oxide | 00000000 | 0000000 |
| D | Standard | 2 1/2" | Pointed | Tip | 3/8" | 0.051" | 16 | Soft Wire | Steel | Black Oxide | 00000000 | 000000 |
| D | Standard | 2 1/2" | Semiflush | Tip | 7/16" | 0.114" | 9 | Soft Wire | Steel | Black Oxide | 00000000 | 000000 |
| E | Standard | 2 3/4" | Flush | Side | 3/4" | 0.114" | 9 | Soft Wire, Nickel Ribbon Wire | Steel | Black Oxide | 00000000 | 000000 |
| F | High Force | 5 1/4" | Semiflush | Side | 3/4" | 0.025" | 22 | Soft Wire | Steel | Black Oxide | 00000000 | 000000 |
| F | High Force | 5 1/4" | Semiflush | Side | 1 1/16" | 0.072" | 13 | Soft Wire | Steel | Black Oxide | 00000000 | 000000 |
Air-Powered Plastic Cutters
Good for high-volume cutting and trimming. Jaws can be mounted in a handle for left- or right-hand use.
Blade | |||||||
|---|---|---|---|---|---|---|---|
| Lg. | Cut Lg. | Cutting Edge Location | For Max. Plastic Thick. | Material | Finish | Each | |
| 3 1/4" | 1" | Side | 3/16" | Steel | Black | 00000000 | 0000000 |
Air-Powered Sheet Metal Nibblers
Straight, Right
Curves, Left Curves
These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion. To start cuts in the center of material, drill a starting hole.
For Max. Thick. | Material | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel | Stainless Steel | Aluminum | Cut Wd. | Min. Cut Radius | Overall Lg. | Punch | Housing | No-Load Strokes per Minute | Flat Stock Cutting Speed, in./min. | Starting Hole Dia. | For Texture | Switch Type | Air Consumption, cfm | Each | |
Cutting Pattern—Right Curves, Straight, Left Curves | |||||||||||||||
(A) For Use On Aluminum, Brass, Copper, Iron, Nickel, Steel, Tin, Plastic | |||||||||||||||
| 3/64" | __ | 1/32" | 1/4" | 1/4" | 7 1/16" | Steel | Aluminum | 3,200 | 62 | 1/2" | Corrugated | Lever | 21 | 00000000 | 0000000 |
(B) For Use On Aluminum, Brass, Copper, Steel, Tin | |||||||||||||||
| 3/64" | __ | 3/64" | 3/16" | 3/16" | 7" | Steel | Plastic | 2,600 | 46.5 | 5/8" | Corrugated | Lever | 4 | 0000000 | 000000 |
(C) For Use On Aluminum, Brass, Copper, Iron, Nickel, Stainless Steel, Steel, Tin | |||||||||||||||
| 3/32" | 5/64" | 1/8" | 1/4" | 2" | 12" | Steel | Aluminum | 192 | 55 | 1 1/2" | Corrugated, Flat | Lever | 27 | 000000 | 000000 |
Cutting Pattern—Straight | |||||||||||||||
(D) For Use On Aluminum, Brass, Copper, Iron, Nickel, Stainless Steel, Steel, Tin | |||||||||||||||
| 11/64" | 1/8" | 11/64" | 3/16" | 6" | 12" | Steel | Aluminum | 192 | 48 | 2 1/2" | Flat | Trigger with Lock | 21-23 | 00000000 | 000000 |
Air-Powered Sheet Metal Cutters for Thin Metal
Straight, Right
Curves, Left Curves
Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.
For Max. Thick. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel | Aluminum | Min. Cut Radius | Overall Lg. | Blade Material | No-Load Strokes per Minute | Air Consumption, cfm | Air Pressure, psi | For Air Hose ID | Air Hose Included | Thread Type | Pipe Size | Gender | Each | |
Cutting Pattern—Straight, Right Curves, Left Curves | ||||||||||||||
For Use On Aluminum, Brass, Copper, Iron, Nickel, Steel, Tin | ||||||||||||||
| 1/64" | 1/64" | 7" | 11" | Steel | 2,200 | 4 | 90 | 1/4"-1/2" | No | NPT | 1/4 | Female | 0000000 | 0000000 |
Air-Powered Sheet Metal Cutters
Straight, Right
Curves, Left Curves
Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion. To start cuts in the center of material, drill a starting hole.
For Max. Thick. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel | Stainless Steel | Aluminum | Cut Wd. | Min. Cut Radius | Overall Lg. | Blade Material | No-Load Strokes per Minute | Starting Hole Dia. | Air Consumption, cfm | Air Pressure, psi | Includes | Each | ||
Cutting Pattern—Straight, Right Curves, Left Curves | ||||||||||||||
For Use On Aluminum, Brass, Copper, Iron, Nickel, Stainless Steel, Steel, Tin | ||||||||||||||
| A | 3/64" | 1/32" | 3/64" | 7/32" | 6" | 10" | Steel | 2,500 | 1/2" | 4 | 90 | Wrench, Lubricant | 0000000 | 0000000 |
| B | 1/16" | 3/64" | 3/32" | 7/32" | 7" | 10 1/2" | Steel | 2,200 | 1/2" | 4 | 90 | Wrench, Lubricant | 0000000 | 000000 |
Air-Powered Pliable Sheet Cutters
Straight, Right
Curves, Left Curves
Leave clean cut edges in a variety of pliable materials. Also known as scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut. Blades do not close completely.
For Max. Thick. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Wire Cloth | Plastic | Overall Lg. | Blade Material | No-Load Strokes per Minute | Air Consumption, cfm | Air Pressure, psi | For Air Hose ID | Air Hose Included | Thread Type | Pipe Size | Gender | Each | |
Cutting Pattern—Straight, Right Curves, Left Curves | |||||||||||||
For Use On Aluminum, Brass, Bronze, Copper, Foam, Nickel, Plastic, Rubber, Stainless Steel, Steel | |||||||||||||
| 3/64" | 1/8" | 12" | Steel | 2,500 | 4 | 90 | 1/4"-1/2" | No | NPT | 1/4 | Female | 00000000 | 0000000 |
Air-Powered Fabric Cutters
The included semi-square blade is for no-fray cuts. This cutter is not for cutting carpet, corrugated material, rubber, plastic, or metal.
Round blade trims and edges, but may cause fraying.
| For Max. Thick. | Overall Lg. | Blade Material | Blade Size | Blade Shape | Horsepower, hp | Air Consumption, cfm | Air Pressure, psi | For Air Hose ID | Air Hose Included | Thread Type | Pipe Size | Gender | Includes | Each | |
Cutting Pattern—Straight, Left Curves, Right Curves | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Use On Fabric | |||||||||||||||
| 3/8" | 9" | Steel | 2 1/32" | Semi Square | 1/3 | 4 | 90 | 1/4" | No | NPT | 1/4 | Male | Built-In Blade Sharpener | 0000000 | 000000000 |
Air-Powered Bolt and Chain Cutters
Slice through bolts and chain with low effort. A spring opens the jaws for quick cuts. Not for use on wire rope.
Cutters | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Dia. | Overall | Replacement Cutting Heads | ||||||||||||||||
| Soft Steel | Medium-Hard Steel | Hard Steel | Rebar | Hard Chain | Lg. | Ht. | Jaw Material | Grip Material | Air Pressure | For Air Hose ID | Air Hose Included | Thread Type | Pipe Size | Gender | Each | Each | ||
| 3/8" | 3/8" | 5/16" | 5/16" | 5/16" | 15" | 7 1/4" | Steel | Rubber | 80-120psi | 3/8" | No | NPT | 3/8 | Female | 0000000 | 000000000 | 0000000 | 0000000 |
| 1/2" | 1/2" | 3/8" | 3/8" | 3/8" | 17 1/2" | 10" | Steel | Rubber | 90-130psi | 3/8" | No | NPT | 3/8 | Female | 0000000 | 00000000 | 0000000 | 000000 |
Air-Powered Steel Drum Head Cutters
Make fast cuts without manual effort. Unlike Electric Steel Drum Head Cutters, this is for use in areas where work surfaces are wet. Nonmarring rollers guide the cutter around the head leaving a clean edge and lip for use with steel drum covers. This cutter is for continuous use. It's also known as a drum deheader.
Drum Capacity, gal. | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Min. | Max. | For Max. Drum Lip Thick., ga. | Blade Material | Material | Ht. | Wd. | Dp. | Air Pressure, psi | Air Consumption, cfm | For Air Hose ID | Air Hose Included | Thread Type | Pipe Size | Gender | Each | |
| 30 | 55 | 16 | Steel | Aluminum, Steel | 25" | 11" | 17" | 60-100 | 25 | 1/2" | No | NPT | 1/4 | Male | 0000000 | 000000000 |