The toughest bits available, these withstand the shock and twisting force of impact drivers.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

A retaining ring at the tip grips inside the recess to ensure screws won't slip off the bit.

A magnet or retaining ring holds the nut in place.

Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

These bits are also known as nut setters.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

The extra-short leg of these keys fits in tight spaces other tools can't and the long-leg ball end allows angled entry to turn screws in hard-to-reach areas.

A bright finish makes these tools stand out, so they're less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

All of the keys in these sets have an extra-short leg to fit into tight spots and a ball end to turn screws at an angle in hard-to-reach places. Their bright chrome-plated finish makes them easy to see, reducing the chance you’ll lose them.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a bright gold-plated finish that makes them easy to see and less likely to be misplaced.

These assorted keys have a detent that grips inside the recess to ensure screws won’t fall off. The ball end allows angled entry to drive fasteners in hard-to-reach areas.

Each size of these keys is a different color for easy identification. When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

A flexible joint provides access to fasteners in hard-to-reach areas.

The zinc coating on these keys resists salt-spray exposure. They turn fasteners from either end and reach into tight spots.

The ball end allows angled entry to turn screws in hard-to-reach areas. Protect your stainless steel screws by using a stainless steel L-key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of stainless steel keys, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Made of beryllium copper that is FM approved, these keys help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. They turn fasteners from either end and reach into tight spots.

Choose a handle based on torque and change shafts to use a different size or drive style. Factory-set screwdrivers ensure you reach the same torque every time.

Insert a bit into the shaft and a magnet holds it in place.

A scaled-down version of standard changeable-shaft screwdrivers, these tools are shorter, slimmer, and easy to take with you. Remove and replace the shaft to use a different tip size.

When working in tight spaces, these short drivers fit where others can't. Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

These sets include an assortment of keys with a ball end on the long shaft, which allows angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

These assorted keys have an extra-long shaft that provides access to fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Each slot is marked with the size. Set these organizers on a bench top or wall mount.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.

These assorted shafts attach to a handle or can be used with socket wrenches and power tools. They have a ball end that allows angled entry to make good contact with the recess when a standard-tip shaft can’t.

Select any key without unfolding the others in the set. The assorted keys turn multiple fastener sizes.

Bright-colored handles make these tools stand out, so they’re less likely to be misplaced. Sets include an assortment of keys for turning multiple fastener sizes.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Pivot the head to access fasteners from an angle.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

A rubber insert grips the plug to prevent damage.

Achieve the best possible grip on hex fasteners and prevent rounding.

Extra length allows access to fasteners on long bolts.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Pivot the head to access fasteners from an angle.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

A magnet holds the fastener securely enough to drive self-tapping screws.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Suitable for occasional maintenance work, these sets are imported.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Pivot the head to access fasteners from an angle.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.