The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The thickness is oversized to allow for finishing to exact requirements.

One side of these sheets and bars is polished to either a brushed finish or a mirror-like finish.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

MIC6 is cast from a high-strength 7000-series aluminum, then stress relieved to maintain dimensional stability during high-speed machining.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

3000 series aluminum stands up to outdoor use, as well as exposure to chemicals. It offers a good combination of strength, formability, and weldability. It's often used for storage tanks, heat exchangers, garage doors, and general sheet metal work.

A honeycomb core is bonded between two aluminum sheets for rigidity.

One side of these sheets and bars is polished to either a brushed finish or a mirror-like finish.

These sheets and bars are tempered to a 1/2-hard or full-hard state to make them over twice as strong as standard 1100 aluminum.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

These sheets and bars are zinc galvanized for good corrosion resistance.

The nickel and molybdenum content gives AR400 carbon steel the ability to resist wear better than all other carbon steel. It's often used as wear strips, liners, and deflector plates.

This UHSS (ultra high-strength steel) allows you to fabricate high-strength parts using thinner material than you could with other types of steel. It is formable, weldable, and more economical than alloy steel.

The lead additive acts as a lubricant, which allows 12L14 carbon steel to withstand very fast machining. It's used to fabricate a wide variety of machine parts.

Also known as flat stock, the thickness on these sheets and bars is held to a tight tolerance.

The thickness is oversized for finishing to your exact requirements.

4130 alloy steel has a low carbon content for good weldability. It's often used for gears, fasteners, and structural applications.

Heat treated for enhanced hardness and strength, A514 alloy steel is suitable for structural applications and supporting heavy loads.

From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

Polished to either a brushed or mirror-like finish, this material is often used to fabricate decorative enclosures and industrial workstations.

Widely used for fabricating fittings and fasteners, 303 stainless steel machines quickly without sticking to cutting tools.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

This material machines faster with less wear on cutting tools than standard 316 stainless steel. It's also called Prodec and Project 70+.

Precision ground on the top and bottom to a tight tolerance.

Also called flat stock, these precision-ground bars are held to tight thickness and width tolerances.

One of the hardest types of stainless steel after heat treating, 440C offers excellent wear and abrasion resistance. It's often used for bearings, valves, and knife blades.

With a higher chromium content than 15-5 PH stainless steel, this high-strength 17-4 PH offers better corrosion resistance. It is also known as 630 stainless steel.

This material is hardened for improved strength and wear resistance.

The titanium content of 321 stainless steel preserves corrosion resistance around weld points.

Able to withstand temperatures up to 2100° F, 330 stainless steel is widely used as components for industrial furnaces, gas turbines, and boilers. It resists cracking when exposed to heating and cooling cycles.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

An ultra-thin layer of silver makes these bars slower to tarnish than unplated copper to provide low electrical resistance at contact points over time.

One side of these sheets has a brushed finish with grain lines running in one direction to mask fingerprints.

182 copper is stronger, harder, and more wear resistant than 110 copper. Also known as RWMA Class 2 chromium copper, it's commonly used in resistance welding, for circuit-breaker parts, and for molds to make plastic parts.

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

353 brass is more formable than 385 brass while maintaining good machinability. Commonly called engraver’s brass, it’s well suited for fabrication processes such as knurling and threading. Use it to make nuts, gears, drawer pulls, and hinges.

One side of these sheets has a brushed finish with grain lines running in one direction to mask fingerprints.

Thickness and width are oversized to allow for finishing.

Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.

Precision ground on the top and bottom, these bars have a tight thickness tolerance of ±0.002".

These sheets and bars are precision ground to a tight thickness tolerance.

These precision-ground sheets and bars are held to a tight thickness tolerance.

The thickness on these bars is precision ground to a tight tolerance.

These bars are precision ground to a tight thickness tolerance.

Also known as flat stock, these bars have an oversized thickness, length, and width for finishing to your exact requirements.

These W1 bars have lower amounts of alloy elements than other tool steels for excellent machinability.

A blend of nickel, chromium, and molybdenum gives these 625 nickel sheets the strength, weldability, and corrosion resistance necessary for use in expansion joints, exhaust systems, and marine components. They are comparable to Inconel 625 and Haynes 625.

This Alloy 22 nickel resists highly corrosive environments better than similar nickel alloys, including 625 and C-276.

These bars are also known as flat stock.

Because Grade 2 titanium is 99% pure, it is more corrosion resistant than Grades 5 and 9 but not as strong. It has good formability and weldability. Common uses include chemical processing equipment, heat exchangers, and marine hardware.

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

Offering greater impact resistance than standard PVC Type 1 with similar chemical resistance, this PVC Type 2 is widely used for parts that are subject to shock.

Create signs and partitions with this easy to cut PVC foam.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

This material prevents the buildup of static charges.

Made of recycled UHMW plastic, these sheets and bars are an economical, environmentally friendly alternative to standard UHMW while still offering the same low-friction surface that prevents sticking and binding.

Made with carbon black, these recycled UHMW sheets are a sustainable alternative to standard UHMW sheets in applications where static electricity is a concern, such as in conveying equipment and chute liners.

Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.

The addition of glass fibers makes this material more abrasion resistant than standard UHMW. It’s also known as Tivar 88.

Compared to our standard UHMW polyethylene, these sheets and bars hold up better to scuffs and scrapes in high-speed, high-precision, and high-impact applications—such as conveyor equipment, chute liners, and machine guards. Also known as Tivar HPV.

Also known as starboard, these sheets and bars won’t degrade when exposed to salt water, humidity, and UV light.

Also known as pipe-grade HDPE, these sheets are about four times more impact resistant than standard HDPE and hold up outdoors, and in wet environments.

This nylon 6/6 material is modified with MDS for a self-lubricating surface that’s more slippery than standard nylon. It's often used in high-friction applications, such as gears and bearings.

Designed for extreme wear resistance, this Kevlar-filled nylon 6/6 material lasts up to 20 times longer than unfilled nylon. Also known as Hydlar Z, it is often used for parts that are continuously exposed to wear and abrasion, such as wear strips and bushings.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

Often used to make gears and wear strips, these cast nylon 6 sheets and bars withstand higher temperatures and are easier to machine than standard nylon 6/6 sheets and bars.

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

The combination of high strength and water resistance, along with a variety of color choices, makes this opaque cast acrylic useful for outdoor signs and containers. It's also known as Lucite and Plexiglas® Acrylic.

Widely used in semiconductor applications, this polypropylene meets UL flame-retardance standards.

One of the softest and most flexible plastics we offer, LDPE is more formable than HDPE.

Often fabricated into signs, packaging, and light duty housings, polystyrene is easy to thermoform.

Made with virgin Teflon® PTFE resins, these sheets and bars surpass most plastics when it comes to chemical resistance and performance in extreme temperatures.

Filled with carbon and graphite, this naturally slippery PTFE stands up to wear better than standard PTFE.

Manufactured from Rulon PTFE, a PTFE material that's modified with epoxy-coated fiber for a super-slippery, impact-resistant surface that resists wear.

Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

Among the strongest plastic materials we offer, Torlon PAI has a slippery surface that resists wear. Use it to make high-friction compressor parts, bearings, and seals.

Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.