Ladder Type Ladder Type | Show |
|---|
|
Ladder Type Ladder Type | Hide |
|---|
|
Material Material |
|---|
|
Step Tread Step Tread |
|---|
| Serrated | |
Capacity Capacity |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Grab Post Height Grab Post Height |
|---|
|
Assembled or Unassembled Assembled or Unassembled |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
Ladder Width Ladder Width |
|---|
|
Mounting Hardware Included Mounting Hardware Included |
|---|
|
Truck-Mount Ladders


Safely and easily climb on and off flatbed trailers. Quick to install and remove, these ladders hook into the prefabricated slots on the sides of most flatbeds. Made of aluminum, they are lightweight and corrosion resistant. Steps are serrated for maximum slip resistance. The bottom step folds up and the grab posts fold down for compact storage.
Note: Ladders meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices.
Overall | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Ht. (A) | Wd. (B) | Dp. (C) | Max. Climbing Ht. | Grab Post Ht. | No. of Steps | Step Tread | Specifications Met | Each | |
Aluminum | |||||||||
375-lb. Capacity | |||||||||
| 5'11" | 21" | 19" | 4'10" | 27" | 3 | Serrated | ANSI A14.2, ANSI A14.7, OSHA Compliant 29 CFR 1926.1053 | 0000000 | 000000000 |
Weld-On Elevating Steps

Good for use as ladder rungs, cut these steps to size with a metal-cutting saw and weld them in place. Maximum cut length is 24". Steps are serrated for maximum slip resistance. They must be welded at each end with welds able to support the rated capacity.
Overall | ||||||
|---|---|---|---|---|---|---|
| Ht. (A) | Dp. (C) | Material | Capacity | Step Tread | Each | |
17" Wd. (B) | ||||||
| 1 1/2" | 2" | Aluminum | 540 lbs. | Serrated | 0000000 | 000000 |
7-ft. Wd. (B) | ||||||
| 1 1/2" | 2" | Aluminum | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | Serrated | 0000000 | 000000 |
20-ft. Wd. (B) | ||||||
| 1 1/2" | 2" | Aluminum | 250 lbs. for 18"-24" Cut Lengths, 540 lbs. Up to 18" Cut Lengths | Serrated | 0000000 | 000000 |
Ceiling-Mount Foldaway Ladders

Access roofs, commercial attics, and mezzanines from inside with these ceiling-mount ladders. When not in use, they fold up for a flush fit with the ceiling surface. Gas springs make it easy to open and close the ladder. Steps are serrated for maximum slip resistance. Cut the ladder on site to the required height. For the ladder to open and close properly, allow a minimum clearance of 91".
Add suspension kits and ladder extensions when mounting the ladder to a suspended ceiling. Suspension kits connect the foldaway ladder to the roof above, providing structural support and preventing side-to-side movement. Ladder extensions connect to the top of the foldaway ladder so you can climb from the suspended ceiling to a roof hatch. They have retractable grab posts that extend up through the roof hatch for you to safely climb onto the roof.
Note: Ladders meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices.

For Ceiling | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Ht. | Opening Wd. | Opening Lg. | Max. Climbing Ht. | Ladder Wd. | No. of Steps | Step Tread | Mounting Hardware Included | Specifications Met | Each | |
Aluminum | ||||||||||
330-lb. Capacity | ||||||||||
| 7'-14' | 31" | 64" | 14' | 23 3/4" | 15 | Serrated | No | OSHA Compliant 29 CFR 1910.23 | 0000000 | 000000000 |


























