With strength for higher load capacities than other ball-grip positioning arms, these arms have a heavy duty construction.

Heavy duty construction adds strength for higher load capacities than other positioning arms.

Bend these arms to hold small equipment such as lights and microphones in almost any position.

Stronger and with greater load capacities than gooseneck-style positioning arms, these arms keep their shape even when moving or when exposed to vibration. They’re often used in robotics and conveyor applications when frequent repositioning isn’t required.

A suction base makes it easy to move and attach these arms to smooth surfaces such as glass and polished metal.

Adjust the flexible arm to nearly any position.

The base is comprised of adjustable magnetic pins which allow it to conform to any shape and grip most metal surfaces.

For more versatility than other low-profile holders, this holder has six locations for mounting indicators and accessories, including two mounting holes and four places to mount an indicator lug back with the included thumb screws.

Use this holder in areas with limited space. It has a nut and bolt for holding a 1/4” lug-back indicator.

Adjust the flexible arm to nearly any position.

Mount these holders into a machine spindle and use with your indicator to center workpieces.

Attach the C-clamp on these holders to your milling machine head to take indicator measurements without obstructing the cutting tool.

Position the arm by adjusting joints at the top, middle, and bottom. The magnetic base provides a solid mount on metal surfaces.

Place the magnetic base on metal surfaces for a solid mount. The base has a V-grooved bottom for mounting on flat and curved surfaces and magnetic release switch for easy setups.

For a solid mount on metal surfaces, these indicators come with a magnetic base. They have a continuous dial numbered clockwise around the face for direct measurements. A spring-loaded plunger retracts and extends to measure objects.

Suspend tools to keep them out of the way but still within reach.

Mount components of Ball-Grip Positioning Arms to the top of a positioning stand or tripod.

Bend and wrap the legs around almost anything while keeping a level mounting surface.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Push the lever to lock the handle and prevent accidental opening.

Hold workpieces of different thicknesses without adjustment.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Push the lever to lock the handle and prevent accidental opening.

Bolt to the side of an object. Often used to clamp lids and covers on containers.

Two sets of mounting holes allow mounting on the bottom or side.

The mounting base secures these clamps to a rail or bar.

Replace worn screws or customize your clamps.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

Attached to an arm you can flex into position, these clamps hold objects such as a flashlight, tool, or instructions.

Push or pull the plunger to hold your workpiece from the side.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Moving parts are sealed to prevent dirt and dust from clogging the clamp.

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Push the lever to lock the handle and prevent accidental opening.

The plunger can be locked at any position along its travel.

Fit the draw arm over a latch plate and pull the handle to clamp.

Push the lever to lock the handle and prevent accidental opening.

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.

The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.

For the most demanding jobs, these clamps have almost five times the capacity of standard fast-action bar clamps.

Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

All adjustments can be made from one end, allowing clamping in tight spaces.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

Screw these clamps directly into a tapped hole in a fixture.

Secure small parts in spring clamps to keep hands free for soldering, gluing, and assembly.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Also known as hatch springs, these supports are commonly used on hatches and other top-opening lids. Raise the lid to extend the spring, which props the lid open—an internal cable keeps the spring from overextending. Press the center of the spring to release the hold and close the lid.

Commonly used on hood and trunk lids, these simple, three-piece rods telescope from 18 1/2" to 46 3/4" to prop lids open at a variety of angles.

Providing constant resistance through the full range of motion, these supports hold lids open at any angle up to 70° or 90°.

Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

For frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

A built-in stop prevents doors from opening too far—good when wall- or floor-stops can’t be used. Designed for frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

Often used on large freezer and cold-storage doors, these closers are designed for doors that weigh 200 lbs. or more.

No need to drill new holes—these closers have a mounting plate that fits the hole patterns of most closers from Norton, LCN, Yale, Corbin Russwin, and Dorma.

Nudge your door and these openers will open it the rest of the way.

Simple and compact, these closers have an arm that rolls along gates to push them closed.

Springs retract to pull storm doors and gates closed.

Use these closers when your door-to-door clearance is limited. They close storm doors more smoothly than standard spring closers.

These openers are often used on older casement and awning windows.

Also known as clamping handles, use these standard adjustable handles for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

Identify equipment controls and components at a glance by their color. Also known as clamping handles, use these handles for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

Prevent unintentional changes to equipment settings—when not in use, these handles are disengaged and turn freely. To change the position, push down on the handle and turn. When you release the handle, it disengages once again. These handles are also known as clamping handles.

For fast clamping anywhere along a threaded rod, press the button to slide the handle into position; release the button to secure. These handles are also known as clamping handles.

An easy-to-grip ball knob makes these handles a good replacement for gear levers. Use them to operate machinery.

Use these handles as grips on hand wheels and cranks to operate machinery.

These handles are often used as grips on hand wheels or cranks to operate machinery around food processing lines without the risk of contaminating the food. Install them on a threaded stud.

Press fit one of these handles into a shaft, rod, or hand wheel to operate machinery.

Ratcheting action allows for quick adjustment to machinery and valves in tight spaces. All of these handles have a straight, open socket head for long shafts to pass through.