McMaster-Carr logo
    Filter by
    System of Measurement
    Bearing Seal Type
    Bearing Type
    Shaft Type
    Bearing Construction
    Static Combined Load Capacity
    Maximum Rotation Speed
    Dynamic Combined Load Capacity
    Shaft Mount Type
    For Housing ID
    Attribute Image
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Roller Material
    Material
    Dynamic Thrust Load Capacity
    Maximum Temperature
    Minimum Temperature
    Rotation Speed
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    3 Products

    Thin-Profile Crossed-Roller Bearings

    Image of Product. Front orientation. Roller Bearings. Thin-Profile Crossed-Roller Bearings.
    For a more compact machine, these bearings have thinner inner and outer rings than high-load crossed-roller bearings. Route hydraulic lines, electrical wiring, and other components through the inside of the bearing. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.
    Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.
    Combined Load
    Cap., lbf
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    Dynamic
    Static
    Max. Rotation
    Speed, rpm
    Lubrication
    Temp. Range,
    ° F
    Features
    Each
    For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring
    15016681,9504,600250Lubricated0 to 175Four Lubrication Holes1378N790000000
     

    Needle-Roller Thrust Bearings

    Image of Product. Bearings. Front orientation. Thrust Bearings. Needle-Roller Thrust Bearings.
    Image of Product. Front orientation. Thrust Roller Bearing Washers.

    Bearings

    Washers

    Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.
    A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Thrust Bearings
    Thin Washers
    For Shaft
    Dia., mm
    OD,
    mm
    Thk.,
    mm
    Cage
    Material
    Dynamic Thrust
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Temp. Range,
    ° F
    Specs. Met
    Each
    Thk.,
    mm
    Each
    Steel
    1501905Steel32,1001,6800 to 240DIN 5405-3, ISO 3035909K966000000015909K1140000000
     

    Washers for Needle-Roller Thrust Bearings

    Image of Product. Front orientation. Thrust Roller Bearing Washers.
    Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
    For Shaft
    Dia., mm
    OD,
    mm
    Thk.,
    mm
    Washer
    Material
    Specs. Met
    Each
    1501901SteelDIN 5405-3, ISO 3035909K1140000000
    back to top