1.504" ID Bearings | McMaster-Carr

Made of naturally slippery plastic so you’ll never have to add lubricant. They’re ideal for clean environments where you need to prevent oil drips or graphite flakes. Compared to metal bearings, they are lighter and will never rust.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

Extreme-Load Ultra-Chemical-Resistant Fiberglass-Backed PTFE—Our strongest PTFE bearings. They’re ideal for heavy loads thanks to a backing layer made of fiberglass. The PTFE core is unaffected by the harsh fluids that other plastics can't handle, including all strong acids and bases.

								Each
	For Shaft Dia.	For Housing ID	Lg.	Dynamic Radial Load Cap. @ Speed	Color	Temp. Range, ° F		1-24	25-99	100-Up
Extreme-Load Ultra-Chemical-Resistant Fiberglass-Backed PTFE



		1 1/2"	1 3/4"	2"	20,200 lb. @ 30 rpm	Gray	-55 to 280	00000000	000000	000000	000000

Oil-Embedded Thrust Bearings

Our simplest-to-use thrust bearings, with no moving parts and no need to lubricate. Their porous surface releases oil over time, so you can install and forget them. While they run in most conditions, oil may drip away if temperatures climb too high. For extremely hot environments, consider graphite-lubricated bearings. All are fabricated, lubricated, and inspected in the U.S.

Extreme-Load Heat-Treated Iron Copper—Our strongest oil-embedded thrust bearings. They're heat treated to form a uniform internal grain that makes them stronger than 863 iron copper. As a result, they're often used to support extreme loads in earth-moving equipment and railroad applications. The increased iron content also makes them appear silver.

Mineral Oil Base—Mineral oil consistently lubricates at most temperatures but doesn’t last as long as synthetic oil.

	OD	Thk.	Dynamic Thrust Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
Extreme-Load Heat-Treated Iron Copper



	1 1/2"	2 1/2"	1/8"	12,000 lb. @ 30 rpm	Mineral Oil	-11 to 400	0000000	00000


	1 1/2"	3 9/16"	9/32"	21,950 lb. @ 30 rpm	Mineral Oil	-11 to 400	0000000	00000

High-Temperature Graphite-Lubricated Thrust Bearings

Keep parts spinning in temperatures as hot as 750° F. Lubricated with graphite, these bearings stay slippery where oil would burn off or solidify. You can install and forget them since the lubricant lasts forever. All are fabricated, lubricated, and inspected in the U.S.

841 Bearing Bronze—A balance of strength and speed makes these bearings a good choice for most applications. Also known as SAE 841 bearing bronze.

	OD	Thk.	Dynamic Thrust Load Cap. @ Speed	Temp. Range, ° F		Each
841 Bearing Bronze



	1 1/2"	2 1/2"	1/8"	5,000 lb. @ 30 rpm	-50 to 700	0000000	00000


	1 1/2"	3 1/2"	3/16"	11,400 lb. @ 30 rpm	-50 to 700	0000000	00000

Ultra-Low-Friction Oil-Embedded Thrust Bearings

Our slipperiest metal thrust bearings glide on machines with frequent starts and stops, such as conveyors. Their oil contains nonstick PTFE particles that reduce wear and heat, extending the life of your equipment. All are fabricated, lubricated, and inspected in the U.S.

841 Bearing Bronze—A balance of strength and speed makes these bearings a good choice for most applications. Also known as SAE 841 bearing bronze.

Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away if the bearing heats up.

	OD	Thk.	Dynamic Thrust Load Cap. @ Speed	Base Oil	Lubricant Additive	Temp. Range, ° F		Each
841 Bearing Bronze



	1 1/2"	2 1/2"	1/8"	6,250 lb. @ 30 rpm	Synthetic Oil	PTFE	-35 to 270	0000000	00000


	1 1/2"	3 1/2"	3/16"	14,250 lb. @ 30 rpm	Synthetic Oil	PTFE	-35 to 270	0000000	00000