1 mm ID Bearings | McMaster-Carr

The most precise bearings we offer, with tolerances tighter than a speck of dust. Rated ABEC 7 out of 9, they meet strict tolerance standards established by the Annular Bearing Engineers Committee (ABEC). You'll find them in equipment that requires both high speed and pinpoint accuracy, such as gyroscopes.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type		Each
Open







				Corrosion-Resistant 440C Stainless Steel

				1	3	1	7	8	100,000	-30	280	Standard	7487N11	000000

Clear Ultra-Impact-Resistant Polycarbonate Round Tubes

Comparable to Lexan, Hyzod, Tuffak, and Makrolon, these polycarbonate tubes are half the weight of glass and maintain excellent impact resistance across a wide temperature range. Use them to make instrument gauge covers and display racks.

Metric

							8 ft. Long
	OD, mm	ID, mm	Fabrication	Temp., ° F	Flammability Rating	Food Industry Std.		Each
1.000 mm Thick Wall (-0.130 mm to 0.130 mm Tolerance)



		3	1	Extruded	-40 to 200	UL 94 HB	FDA Standard	8585K816	00000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to precisely guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. Since the bushing is sized slightly larger than the hole for an extremely tight fit, it’ll stay put permanently. These are ANSI Type PM bushings—also known as headless bushings—which means you don’t need to counterbore the hole to mount them flush.

They also have an internal chamfer that makes it easy to insert bits, pins, and punches without damaging the bushing or misaligning tools.

Don't see the size you need? Additional sizes are available.

DIN 179—DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

						Tolerance, mm								Each
	OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size, mm	For Drill Bit Size Decimal Equiv.	ID	OD	Lg.	Drill Bushing Type	Material	Hardness	Specs. Met		1-5	6-11	12-Up
1 mm ID



		3	6	One End	1	0.0394"	0.006 to 0.016	0.004 to 0.01	-0.1 to 0.1	PM	Steel	Rockwell C61	DIN 179	96990A118	000000	000000	000000


		3	9	One End	1	0.0394"	0.006 to 0.016	0.004 to 0.01	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	96990A119	00000	00000	00000
		4	6	One End	1	0.0394"	0.002 to 0.008	0.019 to 0.027	-0.01 to 0.254	PM	Steel	Rockwell C61	—	96990A851	0000	0000	0000
		4	9	One End	1	0.0394"	0.002 to 0.008	0.019 to 0.027	-0.01 to 0.254	PM	Steel	Rockwell C61	—	96990A852	00000	0000	0000

Metric Press-Fit Drill Bushings with Head


Shown in Countersunk Hole	Shown in Standard Hole

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. They’re ANSI Type H bushings, also known as headed bushings. A flanged head acts as a stop, so these bushings won’t move as you push down your drill bit, reamer, or other cutting bit. Use them even in jigs made of thin or soft materials—the head adds support to protect your jig from damage caused by heavy use. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They’re also used as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear, so they last for many cycles without needing to be replaced.

These bushings meet DIN 172 dimensional standards. This standard is no longer active, but it’s often used as a reference point for making sure parts are compatible with other parts and tools.

To install, fit the bushing into a hole in your jig. In a standard hole, the head will sit above the jig plate; to mount flush, install in a countersunk hole. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once it’s centered, press the bushing into the hole with a hydraulic or lever press.

					Head, mm		Tolerance, mm								Each
	OD, mm	Lg., mm	For Drill Bit Size, mm	For Drill Bit Size Decimal Equiv.	OD	Thk.	ID	OD	Lg.	Drill Bushing Type	Material	Hardness	Specs. Met		1-5	6-11	12-Up
1 mm ID



		3	4	1	0.0394"	6	2	0.006 to 0.016	0.004 to 0.01	-0.1 to 0.1	H	Steel	Rockwell C61	DIN 172	96977A107	000000	000000	000000


		3	7	1	0.0394"	6	2	0.006 to 0.016	0.004 to 0.01	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	96977A108	00000	00000	00000