McMaster-Carr logo
    Filter by
    System of Measurement
    Shaft Diameter
    Attribute Image
    ID
    Attribute Image
    Bearing Type
    Industrial Info Compare
    For Load Direction
    Industrial Info Compare
    Plain Bearing Type
    Cage Material
    For Housing ID
    Attribute Image
    Length
    Attribute Image
    Static Thrust Load Capacity
    Dynamic Thrust Load Capacity
    Bearing Seal Type
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Shaft Mount Type
    Shaft Type
    Maximum Rotation Speed
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    4 Products

    Needle-Roller Thrust Bearings

    Image of Product. Bearings. Front orientation. Thrust Bearings. Needle-Roller Thrust Bearings.
    Image of Product. Front orientation. Thrust Roller Bearing Washers.

    Bearings

    Washers

    Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.
    A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Thrust Bearings
    Thin Washers
    Thick Washers
    For Shaft
    Dia.
    OD
    Thk.
    Cage
    Material
    Dynamic Thrust
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Temp. Range,
    ° F
    Each
    Thk.
    Each
    Thk.
    Each
    Steel
    2 1/4"3"5/64"Steel5,5505,6000 to 24000000000000000.032"00000000000000.126"0000000000000
     

    Washers for Needle-Roller Thrust Bearings

    Image of Product. Front orientation. Thrust Roller Bearing Washers.
    Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
    For Shaft
    Dia.
    OD
    Thk.
    Washer
    Material
    Each
    2 1/4"3"0.032"Steel0000000000000
    2 1/4"3"0.126"Steel000000000000

    Oil-Embedded Sleeve Bearings

    Image of Product. Front orientation. Sleeve Bearings. Oil-Embedded Sleeve Bearings.
    Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.
    With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
    841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.
    Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures.
    For Shaft
    Dia.
    For Housing
    ID
    Lg.
    Dynamic Radial Load
    Cap. @ Speed
    Base Oil
    Temp. Range,
    ° F
    Each
    841 Bearing Bronze
    2 1/4"2 5/8"2"9,000 lb. @ 30 rpmSynthetic Oil-35 to 30000000000000000
     
    back to top