McMaster-Carr logo
    Filter by
    System of Measurement
    Shaft Diameter
    Attribute Image
    Bearing Type
    Industrial Info Compare
    OD
    Attribute Image
    Bearing Seal Type
    Thickness
    For Load Direction
    Ball Bearing Profile
    Ball Material
    Maximum Rotation Speed
    Material
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Compare
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Cage Material
    Rotation Speed
    Shaft Type
    Washer Material
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    3 Products

    Thrust Ball Bearings

    Image of Product. Front orientation. Thrust Bearings. Thrust Ball Bearings.
    Image of Attribute. Front orientation. Contains Annotated. Thrust Bearings. Thrust Ball Bearings.
    For silky-smooth motion, the balls inside these bearings roll nearly friction-free. You'll often find them at the end of a shaft or between a stationary and rotating surface, such as on a propeller or rotary table.
    These bearings come as three separate pieces—one cage and two washers. The cage holds the balls in place, while the washers create a surface for the balls to roll on. This design is easy to lubricate, but the oil will attract dust and grime since it's exposed.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    For Shaft
    Dia., mm
    OD,
    mm
    Thk.,
    mm
    Cage
    Material
    Dynamic Thrust
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Temp. Range,
    ° F
    Includes
    Each
    Steel
    10013525Steel19,1002,400-40 to 250Two Washers7806K7290000000
     

    Needle-Roller Thrust Bearings

    Image of Product. Bearings. Front orientation. Thrust Bearings. Needle-Roller Thrust Bearings.
    Image of Product. Front orientation. Thrust Roller Bearing Washers.

    Bearings

    Washers

    Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.
    A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Thrust Bearings
    Thin Washers
    For Shaft
    Dia., mm
    OD,
    mm
    Thk.,
    mm
    Cage
    Material
    Dynamic Thrust
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Temp. Range,
    ° F
    Specs. Met
    Each
    Thk.,
    mm
    Each
    Steel
    1001354Steel20,4002,4200 to 240DIN 5405-3, ISO 3035909K96100000015909K998000000
     

    Washers for Needle-Roller Thrust Bearings

    Image of Product. Front orientation. Thrust Roller Bearing Washers.
    These hardened steel washers protect softer shafts and housings from the rolling contact of needle rollers. Without them, needle rollers can indent and score unhardened surfaces, leading to premature wear and bearing failure. Positioned between the bearing and each mating surface, these washers distribute thrust loads evenly and extend service life. They adapt needle-roller thrust bearings for unhardened, unground surfaces.
    For Shaft
    Dia., mm
    OD,
    mm
    Thk.,
    mm
    Washer
    Material
    Specs. Met
    Each
    1001351SteelDIN 5405-3, ISO 3035909K998000000
    back to top