58 mm OD Bearings | McMaster-Carr

Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Steel

				45	58	7	1	1,350	13,000	-50	130	Standard	6809	00000000	000000


				Shielded







								Steel

								45	58	7	1	1,350	11,000	-40	150	Standard	6809-2Z	00000000	00000

Permanently Lubricated Ball Bearings

Install and forget these self-lubricating bearings. Their lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Sealed







				Corrosion-Resistant 440C Stainless Steel

				45	58	7	1	1,350	6,000	-10	200	Standard	6809-2RS	00000000	0000000

Needle-Roller Bearings

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Radial Load Cap., lb.
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	For Shaft Surface Smoothness, Ra, μin	Temp. Range, ° F	Specs. Met		Each
For Radial Load—Open with Steel Ring



		50	58	25	8,650	18,850	5,300	Required	8	-20 to 280	DIN 618, ISO 3245	00000000	000000


		For Radial Load—Sealed on Both Sides with Steel Ring



				50	58	24	6,950	14,150	3,150	Lubricated	8	0 to 210	DIN 618	00000000	00000

Combination Ball/Needle-Roller Bearings

A built-in thrust ball bearing reduces wear from adjacent shaft components, while the needle rollers support high radial loads. Install anywhere you would use separate bearings for radial and thrust loads.

						Radial Load Cap., lb.		Thrust Load Cap., lb.
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ball Bearing OD, mm	Ball Bearing Wd., mm	Dynamic	Static	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	For Shaft Surface Smoothness, Ra, μin	Temp. Range, ° F	Features		Each
For Combined Radial and Thrust Load—Open with Steel Ring



		45	58	32	66.5	14	5,600	11,600	6,250	12,380	4,500	Required	8	-20 to 230	Lubrication Groove, Lubrication Hole	00000000	0000000

Ball Bearings for Food and Beverage

Sealed

Food production rolls along smoothly on these bearings. Greased with FDA-compliant lubricant, they’re safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. The lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Food Industry Std.	Bearing Trade No.		Each
Sealed







				Corrosion-Resistant 440C Stainless Steel

				45	58	7	1	1,150	6,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	6809-2RS	00000000	0000000

Bearing Locknuts

Carbon Steel

With a nylon insert that grips your threaded shaft or spindle without damaging its threads, these locknuts—also called shaft nuts—hold bearings, bushings, gears, and pulleys prone to vibration tightly in place. They come as one piece, so you can easily clamp them onto your shaft or spindle. But, since they aren’t made entirely of metal, they don’t stand up to heat as well as all-metal locknuts. Slots in their sides mean you can tighten and loosen them with a spanner wrench or spanner socket. Their face is also chamfered to help keep the size and weight of your assembly at a minimum. All meet international standards for bearing locknut dimensions.

Carbon Steel—All carbon steel locknuts are strong and resist wear, though they don’t stand up to corrosion as well as 303 stainless steel locknuts.

303 Stainless Steel—303 stainless steel locknuts resist corrosion better than carbon steel locknuts but aren’t as strong. They withstand washdowns and chemicals.

Thread Spacing—When choosing your thread spacing, consider the precision of your application. The finer the threads, the more control you have when making adjustments.

	Locknuts										Sockets
	Thread						Carbon Steel		303 Stainless Steel
	Size	Spacing	OD, mm	Wd., mm	Insert Max. Temp., ° F	Specs. Met		Each		Each		Each
Chamfered Face



		M40 × 1.5 mm	Extra Fine	58	12	160	ISO 2982-2	00000000	000000	00000000	000000	00000000	0000000

Bearing Nuts

Carbon Steel

Chamfered Face

Carbon Steel

Stepped Face

Often paired with spring lock washers to strengthen their hold, these bearing nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench or spanner socket.

Carbon Steel—Carbon steel bearing nuts are strong and resist wear.

Chamfered Face—Chamfered-face bearing nuts weigh less and produce less heat than stepped-face nuts.

Stepped Face—Use stepped-face bearing nuts with DIN 462 spring lock washers. You can also use them in pairs or with other bearing nuts. For the nut closer to the bearing, position the stepped face towards the bearing. All meet DIN standards for bearing lockout dimensions.

ISO 2982— Some chamfered-face bearing nuts meet ISO 2982 (formerly DIN 981), an international standard for bearing locknut dimensions. Their sizes correspond to SKF KM series. Use them with DIN 5406 spring lock washers.

Thread Spacing—When choosing your thread spacing, consider the precision of your application. The finer the threads, the more control you have when making adjustments.

	Nuts								Bearing Lock Washers		Sockets
	Thread
	Size	Spacing	OD, mm	Wd., mm	Specs. Met	For Lock Washer Specs. Met		Each		Each		Each
Carbon Steel







				Chamfered Face

				M40 × 1.5 mm	Extra Fine	58	9	DIN 981, ISO 2982	DIN 5406	0000000	00000	000000000	00000	00000000	0000000




						Stepped Face

						M38 × 1.5 mm	Extra Fine	58	11	DIN 1804	DIN 462	0000000	00000	000000000	0000	———	0