We will reply to your message within an hour.
About twice as strong as aluminum rivet nuts, these steel rivet nuts are zinc plated for mild corrosion resistance.
The most corrosion resistant twist-resistant rivet nuts we offer, these stand up to chemicals.
These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.
A hex-shaped body provides the highest twist resistance of any rivet nut.
Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.
The coated flange seals out moisture and prevents corrosion.
These rivet nuts are mildly corrosion resistant.
A PVC coating minimizes the chance of scratching the surface of your material. These rivet nuts are more corrosion resistant than zinc-plated steel rivet nuts.
These kits include one size of low-profile rivet nuts.
About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.
The most corrosion resistant low-profile rivet nuts we offer, these stand up to chemicals.
These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.
About twice as strong as aluminum rivet nuts, these rivet nuts are zinc plated for mild corrosion resistance.
Once installed these rivet nuts have a large back flange that distributes the load across a broad area for a strong hold in plastic and composites.
The thread area is enclosed, which prevents leakage past the threads from either side of your application.
A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.
A nonconductive rubber coating insulates the nut from electricity, seals out moisture, and damps vibration.
Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.
These nuts have three mounting holes to accept screws and rivets for use with thin materials.
These screw-mount nuts are often used to attach glides and levels to wood.
The most corrosion resistant tee nut inserts we offer, these inserts stand up to chemicals and salt water.
Steel inserts have high strength for durability.
These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.
Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.
Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.
Six prongs around the barrel of these inserts provide a strong hold and prevent them from loosening and twisting.
Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.
Hooked prongs give these inserts excellent holding power even when removing screws.
These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.
Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.
Assortments include various sizes of tapping inserts for hardwood.
The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.
Large threads cut into softwood such as particleboard for a strong hold.
Assortments include various sizes of tapping inserts for softwood.
A closed end seals out elements and protects the threads on these inserts from debris.
An open end allows long screws and bolts to pass through the insert.
Mount these inserts flush or below the material's surface.
Knurls hold these inserts in hardwoods such as oak, maple, and walnut to prevent twisting.
These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.
These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.
Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive.
Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.
The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.
These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.
70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.
The barbed sides keep these securely in place even before a screw is installed.
Use these inserts to install fine-thread screws in existing holes.
Push down on the inside of these inserts with an installation tool and they expand to hold firm in surrounding material.
Install these inserts into plastic parts to create a secure base for fasteners.
With the male threaded end on these inserts, mount components directly to plastic parts.
The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.
Assortments include various sizes of inserts, a soldering iron, a ceramic insulation tube, and installation tips.
Also known as Trisert inserts, these cut threads into plastic and have better holding power than press-fit inserts.
These inserts are the most corrosion-resistant thread-locking inserts we offer.
A black-phosphate finish provides mild corrosion resistance.
Made of 18-8 stainless steel, these inserts have better corrosion resistance than black-phosphate steel.
A closed-end tap, drill bit, and installation bit are included with these inserts.
Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.
These assortments include various sizes of thread-locking inserts.
The knurled body holds these inserts in place in aluminum and other soft metals. Use an arbor press to install them in untapped holes.
Made of 18-8 stainless steel, these inserts have good corrosion resistance.
The strongest key-locking inserts we offer, these inserts are made to stringent military specifications.
These inserts are made to stringent military specifications.
Forming the strongest hold of any of our threaded inserts, these inserts have a distorted internal thread to lock screws into place and keys that drive into surrounding material to prevent slipping and rotating.
These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.
Eliminating the need for primer, these inserts are coated to resist corrosion when installed in different materials.
A dry film keeps the screw from sticking or binding in these inserts during installation.
Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.
These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.
Made of nickel alloy, these inserts are more resistant to acids and salt water than stainless steel inserts.
A distorted thread grips the screw to resist loosening.
Without a prong to break off and retrieve, these inserts are often used where debris could cause damage.
Inserts come with a through-hole tap and installation tool.
Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.
Kits include helical inserts, a tap, and an installation tool.
These kits have short-, normal-, and long-reach inserts, an installation tool, and a tap.
These inserts cut their own threads in soft metals such as aluminum, so there's no need to tap the hole. Also known as Tap-Lok inserts.
A wide flange distributes the load over a large area. Hammer these inserts into a drilled hole.
Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.
A ribbed-shaped body holds the nut in place so it won't move when tightening a screw. Assortments contain rivet nuts, mandrels, nosepieces, and a plier-style installation tool.
Use these rivet nuts for light duty fastening in low-clearance applications. Assortments include rivet nuts, mandrels, and an installation tool.
These rivet nuts have a smooth body and fit in smaller holes than twist-resistant rivet nuts. Assortments include rivet nuts, mandrels, nosepieces, and a plier-style installation tool.
Add a stud to thin material when you only have access to one side.