Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Turn a set screw to adjust the door up or down after it's hung.

Made of plastic with a metal additive, these hinges will set off metal detectors if a piece breaks off and falls into your line.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Tighten or loosen an adjustment screw to change the hinge resistance.

In addition to rotating 360°, these hinges tilt up and down.

These hinges allow 360° of motion.

A grease fitting makes these hinges easy to lubricate.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

After a light push on the door, springs in these hinges swing doors and gates fully open.

Springs in these hinges with holes automatically swing doors and gates closed behind you.

Use these hinges on lightweight screen and storm doors as well as small gates.

These hinges with holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

Squeeze the hinge handles together to retract the pin and disconnect a door; release the handles and the pin snaps back.

A stop keeps these hinges open at a set angle; push past the stop to open them to 180°.

A snap-on cover protects these hinges from tampering and creates a finished appearance.

These hinges are completely hidden when the door is closed.

No need for oil or grease, these hinges are maintenance free. The mounting holes form an industry-standard half-moon shape.

A stud projects from the back of each hinge leaf to prevent the door from being forced open. The mounting holes form an industry-standard half-moon shape.

Only one cutout (mortise) is needed to mount these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

To reinforce loose or damaged hinges, mount one of these hinges to the top edge of the pull-side of the door.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Keep environments free of contaminants—with plastic hinge leaves and a metal pin, there's no metal-to-metal contact that can release particles as hinges open and close.

Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.

Choose these hinges for their adherence to strict military standards for material and construction.

Made of carbon fiber, these hinges are as strong as aluminum yet lighter in weight. All have leaves that are connected by a strip of flexible Kevlar instead of a pin.

Mounting slots allow door alignment adjustments during and after hinge installation.

The leaves of these hinges almost touch when the door is closed. They are often used in electrical enclosures for a tight seal.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

A spring in these hinges automatically swings doors and gates closed behind you.

These hinges have wide hinge leaves that provide a large mounting surface to keep freezer and refrigerator doors from sagging.

Bearings allow these hinges to open and close doors smoothly.

To ensure a good fit, these hinges have screws for horizontal, vertical, and depth adjustments after installation.

Spring tension pulls the door closed when it’s open less than 10° and keeps it closed without a catch or latch.

These hinges have a standard range of motion of 100° to 120°.

With a 170° range of motion, these hinges are for doors that need to open wide.

Instead of mounting to the side of a door, mount these hinges to the top and bottom to allow doors to open wide.

Surface-mount these hinges to the side of a cabinet.