Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

Attach a pressure gauge to the side port on these valves. Use with water and air.

For installation through thick insulation, these valves have an extra-long stem. They’re for use with water, oil, air, inert gas, and steam.

Install these low-profile valves in tight spots. Use with water, oil, air, and inert gas.

Often used in testing and sampling applications, these valves open and close with the push of a button. They are designed for installation in tight spots. Use with water, oil, and air.

Open and close these valves with the flip of the toggle switch. They’re often used for equipment testing and gas sampling. All have threads and a hex nut below the handle for installation in instrument panels. Use with water, oil, air, and inert gas.

For fast installation and removal from pipelines, these valves have a union fitting that disassembles into multiple pieces. They’re for use with water, oil, air, inert gas, and steam.

Metal provides more durability than plastic. These valves have barbed fittings that grip onto tubing for a secure hold. Use them with water and air.

Threads and a hex nut below the handle allow you to install these valves in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, inert gas, and steam.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Service these valves without cutting soldered connections. The three-piece bolted body can be disassembled inline for easy access to internal components. Use with water, oil, inert gas, and steam.

For more durability than plastic valves, these are made of metal. A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. Use these valves with water, oil, air, inert gas, and steam.

Use these valves with garden hose and other landscaping equipment. All meet NSF/ANSI 61 for use with drinking water.

Solder these valves to metal tubing for a permanent, leak-tight connection. They meet NSF/ANSI 61 for use with drinking water.

With 45° flared tube fittings, these valves form a tight seal on metal tubing lines for natural gas, propane, and butane.

These top-of-the-line valves are comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

Avoid pressure surges and system shocks that can damage piping by installing these valves that open and close slowly.

Designed to withstand the high temperatures and pressures in steam service applications.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

Safe for automated on/off control in drinking-water systems, these valves meet NSF/ANSI Standard 61.

Slide copper pipe into the solder-connect fittings on these valves and weld for a strong, permanent connection.

Also known as whistle valves, these open and throttle as force is applied to the lever and automatically close upon release. They’re commonly used for spraying, washing, and other applications that require manual discharge of liquid and air. Use with water, oil, air, and inert gas.

To automatically shut off the flow of diesel fuel, fuel oil, kerosene, and oil in case of fire, these UL listed valves automatically close and the handle permanently fuses in place when the ambient temperature reaches 165° F.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For installation in instrument panels, these valves have a hex nut and threads below the handle. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. These valves are for use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With 45° flared tube fittings, these valves form a tight seal on metal tubing. Use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Add fine flow control to tubing lines for oil, butane, diesel fuel, fuel oil, gasoline, kerosene, natural gas, and propane. These valves have a barbed fitting that grips onto tubing, providing a secure hold. Turn the handle to adjust flow in small increments.

Available in smaller pipe sizes than other solenoid flow-adjustment valves, these are often used with gas chromatography equipment and analytical instrumentation. They adjust and regulate flow based on the intensity of the electrical signal into the valve. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

For installation in instrument panels, these valves have a hex nut and threads below the handle. They press down on the outside of tubing to adjust flow without contacting the process media.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

Divert the flow of compressed air and other media to multiple pieces of equipment. Use with water, oil, air, and inert gas.

Also known as shuttle valves, these automatically switch the inlet source as pressure changes; they always direct flow from the higher-pressure side-port inlet to the top-port outlet. Use them with water, oil, air, and inert gas.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

With a shorter end-to-end length than other check valves, these fit in tight spaces.

Rated for up to twice the pressure of standard check valves, these can withstand pressures up to 2,000 psi.

Insert tubing into the fitting—no heat, solder, or flux required.

The metal body is more durable than plastic.

Solder to copper tubing for a permanent, leak-tight connection.

Rated for at least four times the pressure of standard check valves for oil and fuel, these are often used in hydraulic applications with pressures up to 3,000 psi.

Prevent dirty, contaminated water from backing up into your garden hose line—install these valves between a faucet and a garden hose.

Attach these valves with NPT connections to threaded pipe.

Attach these balancing valves using solder—they help you measure the difference in pressure across the valve and adjust the flow rate to system components. Also known as circuit setters, they’re often used in systems that need an even distribution of flow, such as HVAC systems.

Push tubing into these orifices, and an internal ring holds them in place. They're for use with plastic and soft metal tubing.

The large knob makes these drainage valves easy to grip.

With a durable bronze body, these float valves can be used with water and hydraulic fluid.

Smaller than other float valves, these are sized for containers with limited space.

Commonly used in ice-making machines, these valves have floats that rest inside a clear plastic reservoir.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 exhaust center valves.

Create one action with these valves, such as extending a cylinder.

Designed to be mounted inline, these valves can be installed in an easy-to-reach location along your line. They control the speed of air-powered equipment by adjusting the volume of airflow.

These valves handle pressure up to 265 psi. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Slide the knurled sleeve in one direction to stop flow, and slide it back to start flow again.

Install these valves on your air tank outlet—at the end of the day, they automatically close to save energy.

When system pressure reaches the maximum, these valves open and send an air signal to turn on a downstream device such as a discharge valve or throttle. They close and send a signal to turn the device off when pressure drops.

Quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. Also known as quick exhaust valves.

Choose the pressure range you need. When these valves receive an air signal, they quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. They're often used with air compressors that require continuous operation. Also known as quick exhaust valves.

Release pressure in the line between a compressor and an air storage tank, making start-up easier on the motor. These valves open to allow flow into the tank and close when flow stops or reverses direction, preventing air from escaping the tank when the air compressor is not running.

Designed for installation directly to your air-powered tool, these regulators maintain the set air pressure.

A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

These withstand at least double the pressure of our other timer-operated drain valves.

The most basic option for air and inert gas applications.

Change set pressure to suit your application—this valve includes four interchangeable color-coded springs with different set pressure ranges.

Use these valves with liquid argon, liquid nitrogen, and liquid oxygen.

These valves meet ASME Code Section I for use with steam power boilers requiring pressure relief above 15 psi.

These valves are commonly used with pumps in low-pressure water systems.

Cleaned and bagged for oxygen service and other high-purity applications, these valves are built to withstand the extreme cold of liquid carbon dioxide, liquid nitrogen, and liquid oxygen.

To gradually relieve pressure in lines for diesel fuel, fuel oil, gasoline, and kerosene, these valves begin opening at the set pressure and fully open at about 10% over the set pressure.

Use this valve in light duty water systems with garden hose thread (GHT) connections.

Hook up these valves to equipment with garden hose thread (GHT) connections.

Often used for oxygen service and other high-purity applications, these valves are cleaned and bagged to meet CGA G-4.1 standards to prevent contamination.

These valves automatically reduce a high inlet pressure from compressed gas tanks to a lower, stable outlet pressure.

Reduce contaminants in gases used in research sample systems, emission monitoring systems, chromatography, and other high-purity applications. These valves have a 316 stainless steel and brass body with a smooth finish to reduce dust collection and internal components designed to protect the seal and diaphragm from contamination.

Commonly used in TIG welding where gas flow/coverage is a concern.

Valves have a brass body.

Our smallest pressure-regulating valve.

Choose from valves for liquid argon, liquid nitrogen, liquid carbon dioxide, or liquid oxygen tanks.

Designed to reduce contaminants in high-purity applications using hydrogen and methane gas, these valves have a stainless steel and brass body with a smooth finish to reduce dust collection and internal components designed to protect the seal and diaphragm from contamination.

It's like getting four regulators in one—each comes with four springs so you can change between regulating pressure ranges of 2-30, 10-50, 30-90, and 100-180 psi.

Turn the key to manually vent radiators and heaters.