Often used outdoors, these plastic cabinets are corrosion, weather, and impact resistant.

Made of stainless steel, these cabinets are corrosion and acid resistant.

These cabinets are made of steel mesh for air circulation and visibility.

These cabinets are scratch and corrosion resistant for extra durability outdoors.

Keep an eye on inventory without opening the doors.

The doors of these cabinets are made of steel mesh for air circulation and visibility.

The full-height compartment provides storage for tall items such as brooms and shovels.

Often used outdoors, these cabinets are impact and weather resistant.

Keep an eye on inventory without opening the doors.

Use the pegboard in these cabinets to hang and organize tools, keys, and other items.

These cabinets are made of steel mesh for air circulation and visibility.

Made of stainless steel, these cabinets are corrosion and acid resistant.

Store up to 1,000 lbs. per shelf.

These cabinets have open shelves for storing larger supplies and equipment.

Keep an eye on inventory without opening the doors.

These cabinets have the thickest steel construction that we offer and come with removable bin boxes that hang from panels.

Keep an eye on inventory without opening the doors.

These cabinets are more corrosion resistant than steel.

Store your drums horizontally to allow gravity-flow dispensing.

Two slide-out shelves store up to 24 aerosol cans and offer easy access.

Store harsh, nonflammable liquids in these plastic cabinets—even acid vapors won't corrode them.

Use cabinets individually or stacked.

Store your heaviest tools and parts. Use cabinets individually, stacked, or connect side-by-side.

Remove the stackable cabinet and carry only the tools you need.

Use cabinets individually or stacked on top of compatible bench-height drawer cabinets.

Protect drawer beds and tools from scratches and dents.

Cabinets are stackable with others of the same width and depth.

Protect your sensitive components from electrostatic damage.

Plastic cabinets and boxes won't dent, chip, or rust.

Create your own storage system by choosing a frame and adding boxes, which come in a variety of compartment configurations.

Elevate your cabinets off the ground.

Good for areas where noise is an issue, such as offices and corridors.

Twice as thick as other lockers, these lockers are the most durable ones we offer.

Wide instead of deep, these cabinets are often used in narrow aisles.

Padlock these cages to limit access to equipment and supplies.

Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components. Enclosures are made of nonconductive polycarbonate that resists denting, chipping, and cracking.

With a hygienic design, these enclosures minimize spots where food, debris, and water could collect after washdowns. Use them to house and mount switches, buttons, and other components in sanitary environments.

These enclosures have thicker walls than standard aluminum enclosures, but are still a lightweight yet durable alternative to stainless steel.

PVC enclosures are nonconductive and chemical resistant, withstanding solvents, alkalies, and acids.

Made of polycarbonate, these enclosures resist denting, chipping, and cracking better than stainless steel enclosures.

Made of polycarbonate, these enclosures resist denting, chipping, and cracking.

Control access to these enclosures with a key-operated lock.

Mounting feet make attachment to machines and walls hassle-free. These enclosures are small and lightweight for use with sensors, switches, testing devices, and circuit boards.

Made of fiberglass, these enclosures are lightweight and won’t rust, but still shield push-button controls from water, dirt, and oil.

Protect electronics from washdowns in food plants and other sanitary environments. These enclosures mount directly into walls to protect wiring and reduce the surface area that needs to be cleaned. Standard-size push-button holes are already installed, saving you the effort of measuring and cutting holes yourself.

Protect electronics from washdowns in food plants and other sanitary environments. These enclosures have standard-size push-button holes, saving you the effort of measuring and cutting holes yourself.

Mounting feet make attachment to machines and walls hassle-free.

Inspect components without opening the cover.

No need to cut your own holes—these enclosures already have them to make installing push-buttons, switches, and indicating lights quick and easy.

House electrical components in these general purpose enclosures.

These enclosures have internal slots to hold circuit boards in place.

Small and lightweight, these enclosures are used with sensors, switches, and testing devices.

These enclosures allow you to inspect your electronics without opening the cover.

These enclosures are rated NEMA 13 for indoor protection from dirt and oil/coolant spraying.

Two separate chambers allow you to access wiring connections in the lower section without disturbing components that you install in the upper section.

Holes in the cover of these enclosures allow easy installation of push buttons, switches, and indicating lights.

Keep components safe from rain, snow, and ice. These enclosures are rated NEMA 3R for protection from dirt, falling liquids, and light splashing.

Mounted horizontally, such as on machinery or rooftops, these enclosures protect wiring and other electrical components from rain, snow, and ice thanks to their overhanging top.

Made of nonconductive polycarbonate, these enclosures withstand prolonged submersion in water while protecting electronics from dents, chips, and cracks.

Able to withstand periodic submersion in water, these enclosures offer our highest level of protection from liquids. They’re made of fiberglass to resist impact and corrosion from solvents, alkalis, and mild acids.

Install these enclosures on control panels and walls and inspect what’s inside without exposing their contents in wet and outdoor locations.

Attach these enclosures to machine panels and walls by their mounting feet—no need to open the cover and expose sensors, switches, and other electronics in wet locations. Made of aluminum, they’re lighter in weight than stainless steel yet resist rusting from water.

Check on the contents inside these enclosures from every angle without opening them in wet environments.

Mount these enclosures directly to machine control panels in wet environments and view the contents without opening them.

For use in hazardous locations, these enclosures are rated NEMA 7 and 9 and meet UL Class I, Divisions 1 and 2, Groups B, C, and D; Class II, Divisions 1 and 2, Groups E, F, and G; and Class III, Divisions 1 and 2.

House emergency stop buttons, life safety equipment, and other devices that need to be seen with these brightly colored enclosures, which are easy to spot even in high-dust areas.

These enclosures reduce electromagnetic interference (EMI) and radio frequency interference (RFI), which can cause electrical problems like flickering monitors, interrupted data signals, and unwanted radio noise.

Bury these enclosures in the ground or in concrete. They withstand freeze/thaw conditions and have an open bottom for water drainage.

Keep enclosures locked until the power is cut. A multipoint latch connects to a flange-mount disconnect switch (not included) to hold the door closed, preventing potential electrical shock.

These freestanding enclosures have a gasketed door with clamps to ensure a watertight seal. They are rated NEMA 4 and 13 for protection from dirt, washdowns, and oil/coolant spraying.

Build out human-machine interfaces by installing buttons, switches, gauges, and other components to monitor and control machinery.

Snap these enclosures onto 35 mm DIN rail and lock them in place.

Protect tablet computers, touch displays, and readouts in these specially sized enclosures. They are rated IP65 for protection from spraying water.

Create battery-powered, hand-held devices such as card and signal readers—these enclosures have a clear cover for checking screens and status lights inside.

Use these open boxes with adhesive for electronics (also known as potting compound) to encase electronic assemblies and protect them from vibration, tampering, moisture, and corrosives.

House and organize up to 800 lbs. of components such as servers, automation controls, and computers. All are compatible with standard 19" wide components.

Easily access HMI devices, push-buttons, and other electronics mounted on the exterior of an enclosure while keeping contents safe from water, oil, dust, and weather.