The threaded ends on these cords seal out contaminants and resist coming loose from vibration in tough industrial environments and automated systems while sending power and signal to devices with M12 connections.

The insulation on these cords resists abrasion and oil. They're rated NEMA 6P and IP67 to resist corrosion and withstand washdowns and temporary submersion.

Also known as pico cords, these cords are often used with low-current 8 mm proximity and photoelectric switches.

The insulation on these cords resists abrasion and oil. They're rated NEMA 6P and IP67 to resist corrosion and withstand washdowns and temporary submersion.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

These self-coiling cords stretch to full length and then return to their retracted length for tangle-free storage.

After a power failure, these cords must be manually reset, preventing unexpected equipment startup.

Use these cords with computers, lab equipment, and office machines that have IEC connections.

The shielding blocks signal interference from nearby equipment and devices.

Create a vibration-resistant connection—the socket on these cords securely locks onto any male receptacle and will not detach until manually unlocked.

All cords have a country-specific plug on one end and an IEC socket on the other end.

These cords work with any Milwaukee tool with a pin socket (Quik-Lok) connection.

Carry DC power in or out of electronic devices with these cords. All have industry standard barrel-style connections, letting you power electronics from power supplies.

Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.

Hardwire these cords to equipment.

A few turns is all it takes to join these cords, which have thick knuckle threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance.

Use these unshielded cords where signal interference is not a concern.

To send high-speed data in tough, rugged environments, these cords have an M12 connector on one end that threads onto switches, sensors, and other devices prone to vibration. The other end has a traditional RJ45 plug that connects to Ethernet equipment, such as computers, IO modules, and programmable logic controllers (PLCs).

Connect sensors, switches, I/O modules, and computers in tight spaces.

Often used in labs, storage facilities, and offices, the shielding blocks low to moderate signal interference from nearby equipment and devices. These cords have a flange on the socket end to mount them in a panel cutout.

These cords contain a single pair of twisted wires, making them lighter and more flexible than other Ethernet cords. They’re good for transportation, robotics, and automation applications.

Use these unshielded cords where signal interference is not a concern.

Often used in automated applications such as robotics, these cords withstand continuous motion without degrading data transmission.

Attach these caps to the socket end of washdown USB cords to maintain an IP67 rating when cords are not in use.

Pinch the sides on the plugs of these cords to insert them; they lock into a socket to prevent the cord from detaching.

The insulation serves as a tough armor that protects these cords in high-traffic areas.

Connect computers, monitors, printers, and other devices with DB connections.

Display video from one source on two different monitors.

Transmit audio, video, and data signals over long distances with minimal signal loss.

Play audio from one source on two different speakers.

Often used in assembly line networks and Fieldbus connections, these cords have B-coded M12 connections.

Commonly used for movie, stage, and interior building lighting, these cords connect to equipment with five-pin XLR connections.

Use these cords to extend the distance between your FANUC CRX robot arm and your controller.

Save energy by automatically turning off unused outlets. The master outlet controls five outlets and shuts off power to the other outlets when a device plugged into the master is turned off.

Separately control each device plugged into these strips—each outlet has its own power switch.

An isolated ground connection on these outlets protects computers and other sensitive equipment from external signals that interfere with the equipment’s performance.

A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.

With a rubber housing, these outlet strips withstand drops and other impact.

These curved outlet strips clamp onto a pole or table leg.

Install these outlet strips in an opening in workbenches, tables, and other furnishings; the outlets lie flush with the surface for a seamless appearance.

The insulation on these cords resists water, so they can be used outdoors.

Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces.

The insulation resists water, oil, and chemicals, so these cords withstand dirty and greasy environments.

These self-coiling cords return to their retracted length after stretching for tangle-free storage.

Insulated to resist water, oil, and solvents, these cords withstand dirty and greasy environments.

Power multiple devices with one extension cord.

Designed for indoor use, these cords are often used to power appliances.

Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces.

Give the connectors on these cords a quarter turn to lock in place.

Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.

Safely use these connectors with 12 mm proximity switches, console lights, valves, and power supplies in food, beverage, and pharmaceutical applications—they’re FDA compliant for direct food contact.

Push these connectors together to quickly create signal and data connections in tight spaces. All are smaller than M5 and M8 connectors. They also need less space to mate than screw-together connectors, which require two hands to twist them in place.

A sealed housing protects connectors from weather. Sets include a plug and socket with wire leads already installed. They fit standard Molex connectors.

Convert one HDMI size or style to another.

These panel-mount adapters have a female USB connection on both ends to join two USB cables.

Mount these adapters in a panel cutout.

Adapt connections to attach cords to a computer.

Create various data connector configurations by snapping these adapters into the ports of keystone wall plates.

Connect two fiber-optic cords that have the same gender and connection type. These adapters mount to panels of any thickness, as long as you drill a mounting hole first.

Connect two fiber-optic cords that have the same gender and fiber-optic connection type.

Mount these adapters in a panel cutout.

Add a D-sub connection to a printed circuit board (PCB). These connectors are often used in applications involving monitoring, control, and communication.

With a ferrite filter block surrounding their contacts, these connectors control and reduce the electromagnetic (EMI) and radio frequency (RFI) interference traveling through them.

Audio/video HDMI connectors and cords are rated IP67 when mated.

Protect connections in washdown environments while maintaining access—these RJ45 plugs and adapters latch together securely, yet quickly detach.

Push these connectors together for secure Ethernet connections that are quick and easy to connect and disconnect with just one hand. You’ll know when the plug and socket are locked in place when you hear a click.

Pull wires all the way through the connector face, and then use the crimper to cut and crimp wires in one step.

Protect sensitive equipment from electromagnetic interference.

Instead of tossing Ethernet cords with a broken locking tab on their RJ45 plug, fix them with these clips.

Use an Ethernet cable crimper to terminate these plugs.

Two-thirds the size of M12 connectors, these connectors fit into tight spaces and shield against signal interference.