Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.

The face of these grips is flush with the cable-entry point for a seamless appearance.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

These cord grips are lightweight yet durable.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Made of nylon, these grips resist chemicals.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Tighten the screws to secure your cable.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Stop cords from coming loose in wet environments while keeping them along the side of your enclosure in tight spaces.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stainless steel construction offers the most corrosion-resistance of any of our multi-diameter wet-location cord grips.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

The single loop can handle up to six 10-ga. bare wires at once.

Pull one or more cables through conduit.

Made of fiberglass with a plastic tip, this tape is safer to use around energized equipment than metal fish tape.

Use a blower or vacuum to insert this lightweight threading line into conduit or raceway, and attach it to your pulling rope to guide the rope.

Pull wire and cable while maintaining tension until the line can be permanently anchored. Use these clamps with stranded bare steel wire and cable.

Use this flat tape for long runs without bends. Choose from steel or stainless steel.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

Made of stainless steel, these grips have excellent corrosion resistance.

These grips are galvanized steel for good corrosion resistance.

Made of stainless steel, these grips have excellent corrosion resistance.

Snap these grommets into place to hold wire, cable, and cords in wet locations and form a seal against dust, debris, and water.

Attach these clamps by running a wire rope through the jaws to create an attachment point anywhere along the wire rope.

Reduce cable strain caused by equipment hanging from drop-down cable.