Cut the thin layer of rubber in the center of these grommets to create custom IDs to securely hold and protect wire, cable, and cords. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration. Also known as webbed grommets.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Snap these grommets into place and their wings expand against the sides of the hole to lock them in position. Use them to turn rough-edged and uneven holes into smooth holes.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

The center hole has flaps that flex to accommodate various sizes of wire, cable, and cords while still providing dust and debris protection. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Wire, cable, and cords pass through the grommet opening while the bristles fill in the gaps to control dust and debris. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Cut the center of these grommets with a utility knife to create custom IDs. The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Create a tight seal around wire, cable, and cords with these grommets to keep out dust, debris, and moisture.

Snap these grommets into place to hold wire, cable, and cords in wet locations and form a seal against dust, debris, and water.

These grommets have two flanges that snap around holes and flex to compensate for misalignment and movement of pipe and tubing. They're often used for routing applications in panel walls.

The extended neck on the washer of these grommets adds reinforcement so you can use them in thicker material such as woven fabrics. Press them into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Kits include grommets, a cutting punch, a cutting block, an installation punch, and a die set. Use them to create a way to run rope and cable through tarps, covers, and curtains.

The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

This nylon-coated stainless steel trim combines strength with flexibility to hold snugly on flat, round, and irregular-shaped edges. It can also protect wire, cable, and hose.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

Keep moisture out of your enclosure while securing cords in wet environments. Made of polyamide, these grips are lightweight.

Snap these cord grips into place to secure cable in wet environments.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Route cords at a 45° angle when space is tight around enclosures and panels in wet and oily environments.

Good for wet areas where space is tight, these lightweight grips secure cords at a 90° angle while reducing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Made of nylon, these grips resist chemicals.

These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips are nickel-plated brass for good corrosion resistance.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance.

Install additional cables without swapping cord grips by pushing them through the thin, flexible seals on these grips, which have a sanitary design suitable for food-processing and pharmaceutical plants.

With a spring extension to prevent sharp bends, these bushings protects cords from wear and tear better than standard bushings.