Thread Size Thread Size |
|---|
For Use On For Use On |
|---|
|
|
Individual/Set Individual/Set |
|---|
|
Application Application |
|---|
|
Container Type Container Type |
|---|
|
Overall Length Overall Length |
|---|
Width Width |
|---|
Thread Length Thread Length |
|---|
Maximum Tapping Depth Maximum Tapping Depth |
|---|
Drill Bit Decimal Size Equivalent Drill Bit DecimalSize Equivalent |
|---|
|
Drill Bit Size Drill Bit Size |
|---|
Drill Bit Material Drill Bit Material |
|---|
|
Economy Carbon Steel Taps
Often used for thread repair and occasional hand tapping, these carbon steel taps can thread holes in most metal and plastic, but they have a shorter tool life than standard taps.
Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. This lets them cut with less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.
Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they start threads less easily than taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.
Bottoming-chamfer taps cut into the workpiece with just 1-2 chamfered threads. This short chamfer lets them thread holes closer to the bottom than other taps, but they require more torque to start threads.
Thread | Drill Bit | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size | Lg. | Overall Lg. | Size | Decimal Size Equivalent | No. of Flutes | Thread Type | Pitch Dia. Limit | Each | |
Taper Chamfer | |||||||||
Uncoated Carbon Steel | |||||||||
| 0-80 | 5/16" | 1 5/8" | 3/64" | 0.0469" | 3 | UNF | H3 | 000000000 | 00000 |
| 1-72 | 3/8" | 1 11/16" | 53 ga. | 0.0595" | 2 | UNF | H3 | 000000000 | 0000 |
| 2-56 | 7/16" | 1 3/4" | 51 ga. | 0.067" | 3 | UNC | H3 | 000000000 | 0000 |
| 4-40 | 9/16" | 1 7/8" | 43 ga. | 0.089" | 3 | UNC | H3 | 000000000 | 0000 |
| 5-40 | 5/8" | 1 15/16" | 38 ga. | 0.1015" | 3 | UNS | H3 | 000000000 | 0000 |
| 6-32 | 11/16" | 2" | 36 ga. | 0.1065" | 3 | UNC | H3 | 000000000 | 0000 |
| 8-32 | 3/4" | 2 1/8" | 29 ga. | 0.136" | 4 | UNC | H3 | 000000000 | 0000 |
| 10-24 | 7/8" | 2 3/8" | 25 ga. | 0.1495" | 4 | UNC | H3 | 000000000 | 0000 |
| 10-32 | 7/8" | 2 3/8" | 21 ga. | 0.159" | 4 | UNF | H3 | 000000000 | 0000 |
| 12-24 | 15/16" | 2 3/8" | 16 ga. | 0.177" | 4 | UNC | H3 | 000000000 | 0000 |
| 3/16"-24 | 7/8" | 2 3/8" | 5/32" | 0.1563" | 4 | UNS | H3 | 000000000 | 0000 |
| 1/4"-20 | 1" | 2 1/2" | 7 ga. | 0.201" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 1/4"-28 | 1" | 2 1/2" | 3 ga. | 0.213" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 5/16"-18 | 1 1/8" | 2 23/32" | F | 0.257" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 5/16"-24 | 1 1/8" | 2 23/32" | I | 0.272" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 3/8"-16 | 1 1/4" | 2 15/16" | 5/16" | 0.3125" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 3/8"-24 | 1 1/4" | 2 15/16" | Q | 0.332" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 7/16"-14 | 1 7/16" | 3 5/32" | U | 0.368" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 7/16"-20 | 1 7/16" | 3 5/32" | 25/64" | 0.3906" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 1/2"-13 | 1 21/32" | 3 3/8" | 27/64" | 0.4219" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 1/2"-20 | 1 21/32" | 3 3/8" | 29/64" | 0.4531" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 9/16"-12 | 1 21/32" | 3 19/32" | 31/64" | 0.4844" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 9/16"-18 | 1 21/32" | 3 19/32" | 33/64" | 0.5156" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 5/8"-11 | 1 13/16" | 3 13/16" | 17/32" | 0.5313" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 5/8"-18 | 1 13/16" | 3 13/16" | 37/64" | 0.5781" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 3/4"-10 | 2" | 4 1/4" | 21/32" | 0.6563" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 3/4"-16 | 2" | 4 1/4" | 11/16" | 0.6875" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 7/8"-9 | 2 7/32" | 4 11/16" | 49/64" | 0.7656" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 7/8"-14 | 2 7/32" | 4 11/16" | 13/16" | 0.8125" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1"-8 | 2 1/2" | 5 1/8" | 7/8" | 0.875" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1"-12 | 2 1/2" | 5 1/8" | 59/64" | 0.9219" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1"-14 | 2 1/2" | 5 1/8" | 23.5 mm | 0.9252" | 4 | UNS | Not Rated | 000000000 | 00000 |
| 1 1/8"-7 | 2 9/16" | 5 7/16" | 63/64" | 0.9844" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1 1/8"-12 | 2 9/16" | 5 7/16" | 1 1/32" | 1.0313" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1 1/4"-7 | 2 9/16" | 5 3/4" | 1 3/32" | 1.0938" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1 1/4"-12 | 2 9/16" | 5 3/4" | 1 11/64" | 1.1719" | 6 | UNF | Not Rated | 000000000 | 00000 |
| 1 3/8"-6 | 3" | 6 1/16" | 1 7/32" | 1.2188" | 4 | UNC | Not Rated | 000000000 | 000000 |
| 1 3/8"-12 | 3" | 6 1/16" | 1 19/64" | 1.2969" | 6 | UNF | Not Rated | 000000000 | 000000 |
| 1 1/2"-6 | 3" | 6 3/8" | 1 11/32" | 1.3438" | 4 | UNC | Not Rated | 000000000 | 000000 |
| 1 3/4"-5 | 3 3/16" | 7" | 1 9/16" | 1.5625" | 6 | UNC | Not Rated | 000000000 | 000000 |
| 2"-4 1/2 | 3 9/16" | 7 5/8" | 1 25/32" | 1.7813" | 6 | UNC | Not Rated | 000000000 | 000000 |
Plug Chamfer | |||||||||
Uncoated Carbon Steel | |||||||||
| 0-80 | 5/16" | 1 5/8" | 3/64" | 0.0469" | 3 | UNF | H3 | 000000000 | 0000 |
| 1-72 | 3/8" | 1 11/16" | 53 ga. | 0.0595" | 2 | UNF | H3 | 000000000 | 0000 |
| 2-56 | 7/16" | 1 3/4" | 51 ga. | 0.067" | 3 | UNC | H3 | 000000000 | 0000 |
| 4-40 | 9/16" | 1 7/8" | 43 ga. | 0.089" | 3 | UNC | H3 | 000000000 | 0000 |
| 5-40 | 5/8" | 1 15/16" | 38 ga. | 0.1015" | 3 | UNS | H3 | 000000000 | 0000 |
| 6-32 | 11/16" | 2" | 36 ga. | 0.1065" | 3 | UNC | H3 | 000000000 | 0000 |
| 8-32 | 3/4" | 2 1/8" | 29 ga. | 0.136" | 4 | UNC | H3 | 000000000 | 0000 |
| 10-24 | 7/8" | 2 3/8" | 25 ga. | 0.1495" | 4 | UNC | H3 | 000000000 | 0000 |
| 10-32 | 7/8" | 2 3/8" | 21 ga. | 0.159" | 4 | UNF | H3 | 000000000 | 0000 |
| 12-24 | 15/16" | 2 3/8" | 16 ga. | 0.177" | 4 | UNC | H3 | 000000000 | 0000 |
| 3/16"-24 | 7/8" | 2 3/8" | 5/32" | 0.1563" | 4 | UNS | H3 | 000000000 | 0000 |
| 1/4"-20 | 1" | 2 1/2" | 7 ga. | 0.201" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 1/4"-28 | 1" | 2 1/2" | 3 ga. | 0.213" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 5/16"-18 | 1 1/8" | 2 23/32" | F | 0.257" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 5/16"-24 | 1 1/8" | 2 23/32" | I | 0.272" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 3/8"-16 | 1 1/4" | 2 15/16" | 5/16" | 0.3125" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 3/8"-24 | 1 1/4" | 2 15/16" | Q | 0.332" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 7/16"-14 | 1 7/16" | 3 5/32" | U | 0.368" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 7/16"-20 | 1 7/16" | 3 5/32" | 25/64" | 0.3906" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 1/2"-13 | 1 21/32" | 3 3/8" | 27/64" | 0.4219" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 1/2"-20 | 1 21/32" | 3 3/8" | 29/64" | 0.4531" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 9/16"-12 | 1 21/32" | 3 19/32" | 31/64" | 0.4844" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 9/16"-18 | 1 21/32" | 3 19/32" | 33/64" | 0.5156" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 5/8"-11 | 1 13/16" | 3 13/16" | 17/32" | 0.5313" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 5/8"-18 | 1 13/16" | 3 13/16" | 37/64" | 0.5781" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 3/4"-10 | 2" | 4 1/4" | 21/32" | 0.6563" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 3/4"-16 | 2" | 4 1/4" | 11/16" | 0.6875" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 7/8"-9 | 2 7/32" | 4 11/16" | 49/64" | 0.7656" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 7/8"-14 | 2 7/32" | 4 11/16" | 13/16" | 0.8125" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1"-8 | 2 1/2" | 5 1/8" | 7/8" | 0.875" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1"-12 | 2 1/2" | 5 1/8" | 59/64" | 0.9219" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1"-14 | 2 1/2" | 5 1/8" | 23.5 mm | 0.9252" | 4 | UNS | Not Rated | 000000000 | 00000 |
| 1 1/8"-7 | 2 9/16" | 5 7/16" | 63/64" | 0.9844" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1 1/8"-12 | 2 9/16" | 5 7/16" | 1 1/32" | 1.0313" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1 1/4"-7 | 2 9/16" | 5 3/4" | 1 3/32" | 1.0938" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1 1/4"-12 | 2 9/16" | 5 3/4" | 1 11/64" | 1.1719" | 6 | UNF | Not Rated | 000000000 | 00000 |
| 1 3/8"-6 | 3" | 6 1/16" | 1 7/32" | 1.2188" | 4 | UNC | Not Rated | 000000000 | 000000 |
| 1 3/8"-12 | 3" | 6 1/16" | 1 19/64" | 1.2969" | 6 | UNF | Not Rated | 000000000 | 000000 |
| 1 1/2"-6 | 3" | 6 3/8" | 1 11/32" | 1.3438" | 4 | UNC | Not Rated | 000000000 | 000000 |
| 1 3/4"-5 | 3 3/16" | 7" | 1 9/16" | 1.5625" | 6 | UNC | Not Rated | 000000000 | 000000 |
| 2"-4 1/2 | 3 9/16" | 7 5/8" | 1 25/32" | 1.7813" | 6 | UNC | Not Rated | 000000000 | 000000 |
Bottoming Chamfer | |||||||||
Uncoated Carbon Steel | |||||||||
| 0-80 | 5/16" | 1 5/8" | 3/64" | 0.0469" | 3 | UNF | H3 | 000000000 | 0000 |
| 1-72 | 3/8" | 1 11/16" | 53 ga. | 0.0595" | 2 | UNF | H3 | 000000000 | 0000 |
| 2-56 | 7/16" | 1 3/4" | 51 ga. | 0.067" | 3 | UNC | H3 | 000000000 | 0000 |
| 4-40 | 9/16" | 1 7/8" | 43 ga. | 0.089" | 3 | UNC | H3 | 000000000 | 0000 |
| 5-40 | 5/8" | 1 15/16" | 38 ga. | 0.1015" | 3 | UNS | H3 | 000000000 | 0000 |
| 6-32 | 11/16" | 2" | 36 ga. | 0.1065" | 3 | UNC | H3 | 000000000 | 0000 |
| 8-32 | 3/4" | 2 1/8" | 29 ga. | 0.136" | 4 | UNC | H3 | 000000000 | 0000 |
| 10-24 | 7/8" | 2 3/8" | 25 ga. | 0.1495" | 4 | UNC | H3 | 000000000 | 0000 |
| 10-32 | 7/8" | 2 3/8" | 21 ga. | 0.159" | 4 | UNF | H3 | 000000000 | 0000 |
| 12-24 | 15/16" | 2 3/8" | 16 ga. | 0.177" | 4 | UNC | H3 | 000000000 | 0000 |
| 3/16"-24 | 7/8" | 2 3/8" | 5/32" | 0.1563" | 4 | UNS | Not Rated | 000000000 | 0000 |
| 1/4"-20 | 1" | 2 1/2" | 7 ga. | 0.201" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 1/4"-28 | 1" | 2 1/2" | 3 ga. | 0.213" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 5/16"-18 | 1 1/8" | 2 23/32" | F | 0.257" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 5/16"-24 | 1 1/8" | 2 23/32" | I | 0.272" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 3/8"-16 | 1 1/4" | 2 15/16" | 5/16" | 0.3125" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 3/8"-24 | 1 1/4" | 2 15/16" | Q | 0.332" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 7/16"-14 | 1 7/16" | 3 5/32" | U | 0.368" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 7/16"-20 | 1 7/16" | 3 5/32" | 25/64" | 0.3906" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 1/2"-13 | 1 21/32" | 3 3/8" | 27/64" | 0.4219" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 1/2"-20 | 1 21/32" | 3 3/8" | 29/64" | 0.4531" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 9/16"-12 | 1 21/32" | 3 19/32" | 31/64" | 0.4844" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 9/16"-18 | 1 21/32" | 3 19/32" | 33/64" | 0.5156" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 5/8"-11 | 1 13/16" | 3 13/16" | 17/32" | 0.5313" | 4 | UNC | Not Rated | 000000000 | 0000 |
| 5/8"-18 | 1 13/16" | 3 13/16" | 37/64" | 0.5781" | 4 | UNF | Not Rated | 000000000 | 0000 |
| 3/4"-10 | 2" | 4 1/4" | 21/32" | 0.6563" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 3/4"-16 | 2" | 4 1/4" | 11/16" | 0.6875" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 7/8"-9 | 2 7/32" | 4 11/16" | 49/64" | 0.7656" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 7/8"-14 | 2 7/32" | 4 11/16" | 13/16" | 0.8125" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1"-8 | 2 1/2" | 5 1/8" | 7/8" | 0.875" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1"-12 | 2 1/2" | 5 1/8" | 59/64" | 0.9219" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1"-14 | 2 1/2" | 5 1/8" | 23.5 mm | 0.9252" | 4 | UNS | Not Rated | 000000000 | 00000 |
| 1 1/8"-7 | 2 9/16" | 5 7/16" | 63/64" | 0.9844" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1 1/8"-12 | 2 9/16" | 5 7/16" | 1 1/32" | 1.0313" | 4 | UNF | Not Rated | 000000000 | 00000 |
| 1 1/4"-7 | 2 9/16" | 5 3/4" | 1 3/32" | 1.0938" | 4 | UNC | Not Rated | 000000000 | 00000 |
| 1 1/4"-12 | 2 9/16" | 5 3/4" | 1 11/64" | 1.1719" | 6 | UNF | Not Rated | 000000000 | 00000 |
| 1 3/8"-6 | 3" | 6 1/16" | 1 7/32" | 1.2188" | 4 | UNC | Not Rated | 000000000 | 000000 |
| 1 3/8"-12 | 3" | 6 1/16" | 1 19/64" | 1.2969" | 6 | UNF | Not Rated | 000000000 | 000000 |
| 1 1/2"-6 | 3" | 6 3/8" | 1 11/32" | 1.3438" | 4 | UNC | Not Rated | 000000000 | 000000 |
| 1 3/4"-5 | 3 3/16" | 7" | 1 9/16" | 1.5625" | 6 | UNC | Not Rated | 000000000 | 000000 |
| 2"-4 1/2 | 3 9/16" | 7 5/8" | 1 25/32" | 1.7813" | 6 | UNC | Not Rated | 000000000 | 000000 |
Internal Pipe and Conduit Thread Repairing Files
Repair rusted and damaged threads in pipe and conduit. These files are for use in most hole diameters.
Optional file handles slip over the file to provide a comfortable grip.
Files | File Handles | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Threads per Inch | Wd. | Thick. | Overall Lg. | Material | Each | Pkg. Qty. | Pkg. | ||
For Internal Threads | |||||||||
| 8, 10 | 7/16" | 7/16" | 10" | Steel | 0000000 | 000000 | 6 | 0000000 | 00000 |
| 8, 11 1/2 | 7/16" | 7/16" | 10" | Steel | 0000000 | 00000 | 6 | 0000000 | 0000 |
| 10, 14 | 7/16" | 7/16" | 10" | Steel | 0000000 | 00000 | 6 | 0000000 | 0000 |
For Internal and External Threads | |||||||||
| 8, 10, 11 1/2, 14, 16, 18, 24, 27 | 3/8" | 3/8" | 9 1/4" | Steel | 0000000 | 00000 | __ | 000000 | 00 |
Tap Sets
These taps are for use on most metal and plastic. They have a square shank that's compatible with tap wrenches and tap holders for drill presses and milling machines.
Uncoated carbon steel taps are for thread repair and occasional tapping.
Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.
Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.
Bottoming-chamfer taps cut into the workpiece with just 1-2 chamfered threads. This short chamfer lets them thread holes closer to the bottom than other taps, but they require more torque to start threads.
Drill Bit | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Tap Sizes Included | Thread Type | Thread Lg. | Overall Lg. | Size | Decimal Size Equivalent | No. of Flutes | Pitch Dia. Limit | Container Type | No. of Pieces | Each | |
Uncoated Carbon Steel | |||||||||||
| 0-80 | UNF | 5/16" | 1 5/8" | 3/64" | 0.0469" | 3 | H3 | Plastic Case | 3 | 000000000 | 000000 |
| 1-72 | UNF | 3/8" | 1 11/16" | 53 ga. | 0.0595" | 2 | H3 | Plastic Case | 3 | 000000000 | 00000 |
| 2-56 | UNC | 7/16" | 1 3/4" | 51 ga. | 0.067" | 3 | H3 | Plastic Case | 3 | 000000000 | 00000 |
| 4-40 | UNC | 9/16" | 1 7/8" | 43 ga. | 0.089" | 3 | H3 | Plastic Case | 3 | 000000000 | 0000 |
| 5-40 | UNS | 5/8" | 1 15/16" | 38 ga. | 0.1015" | 3 | H3 | Plastic Case | 3 | 000000000 | 0000 |
| 6-32 | UNC | 11/16" | 2" | 36 ga. | 0.1065" | 3 | H3 | Plastic Case | 3 | 000000000 | 0000 |
| 8-32 | UNC | 3/4" | 2 1/8" | 29 ga. | 0.136" | 4 | H3 | Plastic Case | 3 | 000000000 | 0000 |
| 10-24 | UNC | 7/8" | 2 3/8" | 25 ga. | 0.1495" | 4 | H3 | Plastic Case | 3 | 000000000 | 0000 |
| 10-32 | UNF | 7/8" | 2 3/8" | 21 ga. | 0.159" | 4 | H3 | Plastic Case | 3 | 000000000 | 0000 |
| 3/16"-24 | UNS | 7/8" | 2 3/8" | 5/32" | 0.1563" | 4 | H3 | Plastic Case | 3 | 000000000 | 0000 |
| 1/4"-20 | UNC | 1" | 2 1/2" | 7 ga. | 0.201" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 0000 |
| 1/4"-28 | UNF | 1" | 2 1/2" | 3 ga. | 0.213" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 0000 |
| 5/16"-18 | UNC | 1 1/8" | 2 23/32" | F | 0.257" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 5/16"-24 | UNF | 1 1/8" | 2 23/32" | I | 0.272" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 3/8"-16 | UNC | 1 1/4" | 2 15/16" | 5/16" | 0.3125" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 3/8"-24 | UNF | 1 1/4" | 2 15/16" | Q | 0.332" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 7/16"-14 | UNC | 1 7/16" | 3 5/32" | U | 0.368" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 7/16"-20 | UNF | 1 7/16" | 3 5/32" | 25/64" | 0.3906" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 1/2"-13 | UNC | 1 21/32" | 3 3/8" | 27/64" | 0.4219" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 1/2"-20 | UNF | 1 21/32" | 3 3/8" | 29/64" | 0.4531" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 9/16"-12 | UNC | 1 21/32" | 3 19/32" | 31/64" | 0.4844" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 9/16"-18 | UNF | 1 21/32" | 3 19/32" | 33/64" | 0.5156" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 5/8"-11 | UNC | 1 13/16" | 3 13/16" | 17/32" | 0.5313" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 5/8"-18 | UNF | 1 13/16" | 3 13/16" | 37/64" | 0.5781" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 3/4"-10 | UNC | 2" | 4 1/4" | 21/32" | 0.6563" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 3/4"-16 | UNF | 2" | 4 1/4" | 11/16" | 0.6875" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 7/8"-9 | UNC | 2 7/32" | 4 11/16" | 49/64" | 0.7656" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 7/8"-14 | UNF | 2 7/32" | 4 11/16" | 13/16" | 0.8125" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 1"-8 | UNC | 2 1/2" | 5 1/8" | 7/8" | 0.875" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 1"-12 | UNF | 2 1/2" | 5 1/8" | 59/64" | 0.9219" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 1"-14 | UNS | 2 1/2" | 5 1/8" | 23.5 mm | 0.9252" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 00000 |
| 1 1/8"-7 | UNC | 2 9/16" | 5 7/16" | 63/64" | 0.9844" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 1 1/8"-12 | UNF | 2 9/16" | 5 7/16" | 1 1/32" | 1.0313" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 1 1/4"-7 | UNC | 2 9/16" | 5 3/4" | 1 3/32" | 1.0938" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 1 1/4"-12 | UNF | 2 9/16" | 5 3/4" | 1 11/64" | 1.1719" | 6 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 1 3/8"-6 | UNC | 3" | 6 1/16" | 1 7/32" | 1.2188" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 1 3/8"-12 | UNF | 3" | 6 1/16" | 1 19/64" | 1.2969" | 6 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 1 1/2"-6 | UNC | 3" | 6 3/8" | 1 11/32" | 1.3438" | 4 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 1 3/4"-5 | UNC | 3 3/16" | 7" | 1 9/16" | 1.5625" | 6 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| 2"-4 1/2 | UNC | 3 9/16" | 7 5/8" | 1 25/32" | 1.7813" | 6 | Not Rated | Plastic Case | 3 | 000000000 | 000000 |
| No. of Pieces | Tap Sizes Included | Thread Type | Container Type | Each | |
Uncoated Carbon Steel | |||||
|---|---|---|---|---|---|
| 60 | 3 each of sizes: 1/4"-20 1/4"-28 5/16"-18 5/16"-24 3/8"-16 3/8"-24 7/16"-14 7/16"-20 1/2"-13 1/2"-20 9/16"-18 9/16"-12 5/8"-11 5/8"-18 3/4"-10 3/4"-16 7/8"-9 7/8"-14 1"-8 1"-12 | UNC, UNF | Plastic Case | 0000000 | 0000000 |
| No. of Pieces | Tap Sizes Included | Each | |
Uncoated Carbon Steel | |||
|---|---|---|---|
| 113 | 5 each of sizes: M3 × 0.50 mm M3 × 0.60 mm M4 × 0.70 mm M4 × 0.75 mm M5 × 0.80 mm M5 × 0.90 mm M6 × 1.00 mm M6.3 × 1.00 mm M7 × 1.00 mm M8 × 1.00 mm M8 × 1.25 mm M9 × 0.75 mm M9 × 1.00 mm M9 × 1.25 mm M10 × 1.00 mm M10 × 1.50 mm M11 × 1.50 mm M12 × 1.25 | 0000000 | 0000000 |
Pipe and Conduit Tap Sets
Create pipe and conduit threads in a range of hole diameters. With a square shank, these taps are compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer for start-to-finish thread tapping.
Carbon steel taps are for thread repair and occasional tapping.
| No. of Pieces | Chamfer Type | Pipe Size | No. of Flutes | Container Type | Each | |
Uncoated Carbon Steel | ||||||
|---|---|---|---|---|---|---|
| 6 | Plug | 1/8 1/4 3/8 1/2 3/4 1 | 4, 5 | Fabric Pouch | 0000000 | 0000000 |
Tap and Drill Bit Sets
Drill and tap a variety of hole sizes. All taps and drill bits are for use on most metal and plastic.
Carbon steel taps are for thread repair and occasional tapping.
Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.
Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.
Bottoming-chamfer taps cut into the workpiece with just 1-2 chamfered threads. This short chamfer lets them thread holes closer to the bottom than other taps, but they require more torque to start threads.
| No. of Pieces | Chamfer Type | Tap Sizes Included | No. of Flutes | Drill Bit Sizes Included | Drill Bit Material | Container Type | Includes | Each | |
Uncoated Carbon Steel Taps | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 13 | Plug | 1 each of sizes: 4-40 6-32 8-32 10-24 10-32 1/4"-20 | 3, 4 | 43 ga. 35 ga. 29 ga. 25 ga. 21 ga. 7 ga. | Black Oxide High-Speed Steel | Plastic Case | Tap Wrench | 0000000 | 000000 |
| 29 | Taper, Plug, Bottoming | 3 each of sizes: M3 × 0.50 mm M4 × 0.70 mm M5 × 0.80 mm M6 × 1.00 mm M8 × 1.25 mm M10 × 1.50 mm M12 × 1.75 mm | 3, 4 | 2.5 mm 3.3 mm 4.2 mm 5.0 mm 6.8 mm 8.5 mm 10.2 mm | Black Oxide High-Speed Steel | Metal Case | Tap Wrench | 0000000 | 000000 |
Tap and Die Sets
Use a single set for many sizes of internal and external threads. The taps and dies are for use on most metal and plastic. Hex-shaped dies are for thread repair and can be used with conventional wrenches.
Carbon steel taps are for thread repair and occasional tapping.
Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes
Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper-chamfer taps. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.
| No. of Pieces | Tap Sizes Included | Tap Chamfer Type | Die Shape | Die Sizes Included | Wd. | Container Type | Includes | Each | |
Carbon Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
Right-Hand Thread | |||||||||
| 12 | 1/8, 1/4, 3/8, 1/2, 3/4, and 1 | Taper | Hex | 1/8, 1/4, 3/8, 1/2, 3/4, and 1 | 1 1/16", 1 1/4", 1 7/16", 1 5/8", 2", 2 3/8" | Plastic Case | __ | 0000000 | 0000000 |
| 24 | 1/8"-27, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, and 1/2"-20 | Plug, Taper | Hex | 1/8"-27, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, and 1/2"-20 | 1" | Plastic Case | Die Wrench, Tap Wrench | 000000 | 000000 |
| 24 | 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | Plug, Taper | Hex | 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | 1" | Plastic Case | Die Wrench, Tap Wrench | 00000000 | 00000 |
| 40 | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, and 1/2"-20 | Plug, Taper | Hex | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, and 1/2"-20 | 5/8", 1" | Plastic Case | Die Wrench (2), Tap Wrench (3), Thread Gauge | 0000000 | 000000 |
| 40 | 6-32, 8-32, 10-24, 1/8"-27, 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, and M12 × 1.75 mm | Plug, Taper | Hex | 6-32, 8-32, 10-24, 1/8"-27, 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, and M12 × 1.75 mm | 5/8", 1" | Plastic Case | Die Wrench (2), Tap Wrench (3), Thread Gauge | 0000000 | 000000 |
| 40 | 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | Plug, Taper | Hex | 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | 5/8", 1" | Plastic Case | Die Wrench (2), Tap Wrench (3), Thread Gauge | 0000000 | 000000 |
| 50 | 1/8"-28, 1/4"-19, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, and M18 × 2.50 mm | Plug, Taper | Hex | 1/8"-28, 1/4"-19, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, and M18 × 2.50 mm | 1", 1 7/16" | Plastic Case | Die Wrench (2), Tap Wrench (3), Thread Gauge | 0000000 | 000000 |
| 53 | 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/4"-18, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18, 3/4"-10, and 3/4"-16 | Plug, Taper | Hex | 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/4"-18, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18, 3/4"-10, and 3/4"-16 | 1", 1 7/16" | Plastic Case | Die Wrench (2), Screwdriver, Tap Wrench (3), Thread Gauge | 0000000 | 000000 |
| 63 | 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, and M24 × 3.00 mm | Plug, Taper | Hex | 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, and M24 × 3.00 mm | 5/8", 1", 1 3/16", 1 7/16", 1 13/16" | Plastic Case | Die Wrench (4), Tap Wrench (4), Thread Gauge | 0000000 | 000000 |
| 65 | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/4"-18, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18, 3/4"-10, 3/4"-16, 7/8"-9, 7/8"-14, 1"-8, and 1"-14 | Plug, Taper | Hex | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/4"-18, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18, 3/4"-10, 3/4"-16, 7/8"-9, 7/8"-14, 1"-8, and 1"-14 | 5/8", 1", 1 7/16", 1 13/16" | Plastic Case | Die Wrench (4), Tap Wrench (4), Thread Gauge | 00000000 | 000000 |
| 75 | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | Plug, Taper | Hex | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | 5/8", 1" | Plastic Case | Die Wrench (2), Tap Wrench (3), Thread Gauge (2) | 0000000 | 000000 |
Tap, Die, and Drill Bit Sets
Cut and repair threads and drill holes in many different sizes. Tap and die wrenches are included. The dies are hex shaped for use with conventional wrenches. The taps are made of carbon steel and are recommended for thread repair and occasional tapping.
Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes
Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.
| No. of Pieces | Tap Sizes Included | Die Sizes Included | Drill Bit Sizes Included | Container Type | Includes | Each | |
Carbon Steel | |||||||
|---|---|---|---|---|---|---|---|
Right-Hand Thread | |||||||
| 116 | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | 4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, and M12 × 1.75 mm | 5/64", 7/64", 5/32", 1/4", 19/64", 5/16", 21/64", 3/8", 25/64", 13/32", 27/64", 29/64", 43 ga., 39 ga., 36 ga., 30 ga., 29 ga., 25 ga., 21 ga., 20 ga., 16 ga., 9 ga., 7 ga., 3 ga., B, F, H, I, J, O, Q, R, S, U, and Z | Plastic Case | Die Wrench (2), Extractor (5), Tap Wrench (3), Thread Gauge (2) | 00000000 | 0000000 |
Thread Repairing Tap, Die, and File Sets
Repair screw threads in a wide range of sizes. The dies are hex shaped for use with conventional wrenches. The taps have a square shank that's compatible with tap wrenches and tap holders for drill presses and drilling machines. With a plug chamfer, all taps have 3-5 chamfered threads and are suitable for thread repair in both through holes and closed-end holes.
| Number of Pieces | Tap Sizes Included | Die Sizes Included | File Sizes Included | Container Type | Each | |
Carbon Steel | ||||||
|---|---|---|---|---|---|---|
Right-Hand Thread | ||||||
| 53 | 1/4”-20, 1/4”-28, 5/16”-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16”-12, 9/16"-18, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, and M12 × 1.75 mm | 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, 9/16"-12, 9/16"-18, 5/8"-11, 5/8"-18, 3/4"-10, 3/4"-16, 3/4"-20, M6 × 1.00 mm, M6 × 1.25 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M8 × 1.50 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 1.50 mm, and M20 × 1.50 mm | For 11 to 24 threads per inch, For 0.8 to 3 mm thread pitches | Plastic Case | 00000000 | 0000000 |