Surface mount with the adhesive back to route low-voltage data and control cable where you can't get inside walls.

Insert and remove cable at any point along the length of this open-top, hook-shaped raceway.

Gaskets on the covers and at connection points protect against dust as well as seeping oil and coolant.

This raceway system is also known as wireway and wire trough.

With a top that overhangs the cover, this raceway keeps out rain. It is rated NEMA 3R for protection from liquids and light splashing.

Wrap this sleeving around wire, cable, and hose without disconnecting them. It has a slit along the entire length and wraps over itself to stay closed without an adhesive strip or other closure.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Often used in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390° F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

This sleeving reflects heat away from contents and withstands temperatures up to 300° F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 900° F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tested to meet MIL-STD-202, this sleeving meets performance standards for flame retardance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

This sleeving withstands temperatures over 1000° F, such as in refineries.

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.

A specially formulated silicone rubber coating allows this sleeving to stretch to twice its relaxed ID to fit over items during installation; it then tightens around its contents for a secure fit.

This sleeving withstands temperatures up to 390° F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.

Often used as an alternative to cable ties, wire duct guides and organizes short runs of electrical wiring in enclosures, control panels, and machines.

A hinged cover allows easy access to your wire and cable. It also keeps the sidewalls secure, so this duct is sturdier than duct with a snap-on cover.

This wire duct completely encloses wire and cable.

When used with liquid-tight fittings, this conduit seals out liquid. The steel core provides crush resistance, and the cover is UV light resistant.

In addition to resisting oil, this conduit resists lubricants and grease.

The spiral design makes this conduit more flexible than abrasion-resistant liquid-tight flexible plastic conduit.

Protect fiber optic cable with this small-diameter conduit.

Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.

Covered with a copper braid, this conduit protects wire and cable from electromagnetic interference (EMI) caused by motors and other equipment.

This impact- and crush-resistant conduit is also known as galvanized rigid conduit (GRC).

Also known as intermediate metallic conduit (IMC), this is lighter in weight than thick-wall (rigid) steel conduit, yet it has the same strength.

The most corrosion-resistant thin-wall conduit we offer, use this along walls and ceilings in food-processing and chemical plants.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Wrap this sleeving around cable, cords and wires to protect them and to form bundles.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

These enclosures have internal slots to hold circuit boards in place.

Small and lightweight, these enclosures are used with sensors, switches, and testing devices.

These enclosures withstand temperatures up to 475° F.

House electrical components in these general purpose enclosures.

These enclosures have thicker walls than standard aluminum enclosures, but are still a lightweight yet durable alternative to stainless steel.

Made of polycarbonate, these nonconductive enclosures resist denting, chipping, and cracking.

With a hygienic design, these enclosures minimize spots where food, debris, and water could collect after washdowns. Use them to house and mount switches, buttons, and other components in sanitary environments.

Fiberglass enclosures resist denting better than metal and are more UV resistant than polycarbonate enclosures. They are nonconductive.

Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components.

View all sides of your installed components.

Control access to these enclosures with a key-operated lock.

Mounting feet make attachment to machines and walls hassle-free.

Made of polycarbonate, these enclosures resist denting, chipping, and cracking better than stainless steel enclosures.

Made of polycarbonate, these enclosures resist denting, chipping, and cracking better than stainless steel enclosures.

Made of aluminum, these enclosures resist corrosion from rain, sleet, and snow. While not as corrosion resistant as stainless steel, aluminum is lighter for better mobility, and also easier to machine for custom mounting.

Fans built in to these enclosures keep electronics at the temperature you set, and the filtered intake and exhaust let cool air flow through the enclosure without letting water and contaminants in.

Bury these enclosures in the ground or in concrete. They withstand freeze/thaw conditions and have an open bottom for water drainage.

Make your push buttons, switches, and indicating lights more visible and ergonomic to use. Enclosures mount on either of two sides, creating a 30° or 60° slanted surface.

Able to withstand periodic submersion in water, these enclosures offer our highest level of protection from liquids. They’re made of fiberglass to resist impact and corrosion from solvents, alkalis, and mild acids.

Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components.

For use in enclosures and panels where components require battery power, these enclosures have contacts for AA and 9-volt batteries.

Protect tablet computers, touch displays, and readouts in these specially sized enclosures. They are rated IP65 for protection from spraying water.

A 9-volt battery fits inside a compartment in these enclosures to power testing devices and other hand-held instruments.

Rated NEMA 4 for protection from dirt and washdowns.