Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. They have a 90° corner for milling square corners in slots, pockets, and edges.

Remove large amounts of material quickly without sacrificing tool life. Variable spacing between flutes reduces cutting time and vibration in high-volume jobs.

Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. They have a high helix angle and a wear-resistant coating for excellent shearing and chip removal in stainless steel and titanium.

Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds. They have a high helix angle and a wear-resistant coating for excellent shearing and chip removal in stainless steel and titanium.

A titanium-carbonitride (TiCN) coating prevents soft material, such as aluminum, brass, and bronze, from accumulating on the cutting edge and creating an uneven finish.

Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds. They are uncoated for use in soft material, such as aluminum, brass, and bronze.

Three high-helix-angle flutes provide a smooth finish on nickel alloys, such as Monel, Inconel, and Hastelloy.

Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds.

With a higher helix angle than standard high-speed steel end mills, these clear more chips and generate less heat, making them good for milling soft material, such as aluminum, brass and bronze.

A higher helix angle means these end mills clear more chips than other roughing cobalt steel end mills, making them better for milling aluminum, brass, and bronze. Serrations along the cutting edge act as chip breakers, so they can remove large amounts of material at high speeds.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. Made of solid carbide, they are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material.

Flutes have a low helix angle to provide the cutting forces required for difficult-to-machine material, such as tool steel, hardened steel, and iron.

A titanium-carbonitride (TiCN) coating prevents soft material, such as aluminum, brass, and bronze, from accumulating on the cutting edge and creating an uneven finish.

Use these end mills for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

When one end wears out, switch to the opposite end for two times the life of a standard high-speed steel end mill. Made of high-speed steel, these end mills are for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

With better heat and wear resistance than high-speed steel, these cobalt steel end mills can run at higher speeds and provide better performance on hard material, such as iron, hardened steel, titanium, and tool steel. When one end wears out, turn the tool around for a sharp edge.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material. Also known as taper degree end mills, they're often used to machine angled slots in dies and molds.

With a wear-resistant coating and high helix angle, these end mills provide excellent shearing and chip removal in stainless steel and titanium. Often used for slotting and pocketing cuts in mold and die making, these end mills have a 90° profile and rounded corners, which reduce flute breakage and chipping.

Made of cobalt steel, these end mills have good heat and wear resistance, so they can run at high speeds in hard material. Often used for slotting and pocketing cuts in mold and die making, they have a 90° profile and rounded corners, which reduce flute breakage and chipping.

Made of cobalt steel, these end mills have good heat and wear resistance, so they can run at high speeds in hard material. A 90° pointed tip allows them to be used for drilling as well as for slotting, profiling, chamfering, and spotting cuts.