For longer tool life and a better finish in general purpose milling applications, these solid carbide end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills.

A 45° corner chamfer improves cutting edge strength, so these end mills last longer than standard square end mills when milling hard material; however they do not create as sharp of a corner. Variable spacing between the flutes reduces vibration, allowing them to provide fast cuts, smooth finishes, and long tool life.

Also known as NC tolerance end mills, these carbide end mills have oversize mill diameter tolerances. They're sized to match standard high-speed steel end mills, so you can use them as longer-lasting replacements without changing the size of the cut.

Intersecting flutes create a fine finish, making these end mills good for operations requiring light stock removal, such as deburring, profiling, and finishing.

With a wear-resistant coating and high helix angle, these end mills provide excellent shearing and chip removal in stainless steel and titanium.

A titanium-carbonitride (TiCN) coating prevents soft material, such as aluminum, brass, and bronze, from accumulating on the cutting edge and creating an uneven finish.

Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds. They are uncoated for use in soft material, such as aluminum, brass, and bronze.

Alternating layers of titanium-nitride (TiN) and titanium-aluminum-nitride (TiAlN) coatings give these end mills the hardness, wear resistance, and temperature resistance needed for cutting tool steel, hardened steel, and iron.

Use these end mills for short runs and general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

Commonly used to make keyways in rotary shafts, these tools have a -0.0015" to 0.0000" mill diameter tolerance for creating a precise fit.

With better heat and wear resistance than high-speed steel, these cobalt steel end mills can run at higher speeds and provide better performance on hard material, such as iron, hardened steel, titanium, and tool steel.

A higher helix angle means these end mills clear more chips than other roughing cobalt steel end mills, making them better for milling aluminum, brass, and bronze. Serrations along the cutting edge act as chip breakers, so they can remove large amounts of material at high speeds.

Use these tools with low-horsepower, manual milling machines. They have clamps for holding inserts that do not have a mounting hole. Replaceable carbide-insert end mills reduce waste and cost in high-volume jobs—when the cutting edges dull, replace the carbide inserts instead of the entire end mill.

Fasten carbide inserts directly to these end mills for a hold that's strong enough to handle the high speeds of a CNC machine. Replaceable carbide-insert end mills reduce waste and cost in high-volume jobs—when the cutting edges dull, replace the carbide inserts instead of the entire end mill.

For longer tool life and a better finish in general purpose milling applications, these solid carbide end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills.

These end mills have a diamond or diamondlike coating for machining abrasive material, such as carbon fiber, fiberglass, and graphite.

With a wear-resistant titanium-aluminum-nitride (TiAlN) coating, these end mills provide excellent shearing and chip removal in stainless steel and titanium.

When one end wears out, switch to the opposite end for two times the life of a standard carbide end mill. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

With a higher helix angle than standard high-speed steel end mills, these clear more chips and generate less heat, making them good for milling soft material, such as aluminum, brass and bronze.

Make finishing cuts in tool steel and hardened steel with these cubic boron nitride (CBN) end mills. Harder than carbide end mills, they’re better for making small, precise cuts and last more than five times as long.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. Also known as taper degree end mills, they're often used to machine angled slots in dies and molds.

For longer tool life and a better finish in general purpose milling applications, these solid carbide end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills. Often used for slotting and pocketing cuts in mold and die making, these end mills have a 90° profile and rounded corners, which reduce flute breakage and chipping.

A long neck allows deep cuts. Coated with titanium aluminum nitride (TiAlN), these end mills have the hardness, wear resistance, and temperature resistance needed for cutting tool steel, hardened steel, and iron.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their angled profile allows chamfer, bevel, and other angled cuts.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. The teeth are angled on both sides so you can make top and bottom chamfer cuts without having to flip the workpiece.

These carbide-tipped end mills provide a sharper, harder cutting edge and better wear resistance than high-speed steel without the brittleness of solid carbide. Their teeth are angled on both sides so you can make top and bottom chamfer cuts without having to flip the workpiece.

When one end wears out, switch to the opposite end for two times the life of a standard carbide end mill. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Use them to round sharp corners on the edge of your workpiece.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. They have scooped corners for rounding the sharp edges of your workpiece.

Create dovetail grooves that allow O-rings to flex without falling out of place.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. They create dovetail slots for connecting two components with a sliding fit.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than cobalt steel for the longest life and best finish on hard material. A 90° pointed tip allows them to be used for drilling as well as for slotting, profiling, chamfering, and spotting cuts.

Use these end mills for general purpose keyseat cutting in a wide range of material, including aluminum, iron, and steel. They mill precise notches in rotary shafts to fit machine keys and can also be used for slot milling.

With better heat and wear resistance than high-speed steel, these cobalt steel keyseat cutters can run at higher speeds and provide better performance on hard material. They mill precise notches in rotary shafts to fit machine keys and can also be used for slot milling.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. They're often used to create slots in machine tool tables, indexing tables, and other workholding surfaces.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. With curved, side-cutting teeth, they create hollow, inward-curving grooves.

For general purpose milling in most material, the end mills in these sets have one milling end and a standard shank.

The end mills in these sets have one milling end and a standard shank. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

These multifunction tools have a 90° pointed tip that allows them to be used for drilling as well as for slotting, profiling, and chamfering cuts.

Offering two times the life of a standard carbide end mill, the end mills in these sets have two milling ends so you can switch to the opposite end when one end wears out. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

Also known as shell cutters, these high-speed steel cutters are good for face and side milling. They have a large mill diameter for removing a large amount of material per pass.

These kits include a cutter body, inserts, wrenches, and screws, so you can create your own face milling cutters, which are also known as indexable face milling cutters.

Made of solid carbide, these saws are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material. Use them for cutoff, slitting, and slotting applications.

With peripheral and side teeth, these saws remove chips for a consistent cutting width.

Create square slots, pockets, and edges in wood.

Cut square slots, pockets, and edges in plastic.

With a diamond coating, these bits resist wear when used on ceramics and other highly abrasive material. All have a square cut style to create slots, pockets, and edges.

The diamond-pattern flutes and cutting edges produce a fine finish on composite material.

Cut layers of material flush to one another. All bits have a pilot to guide cuts.

These bits have a straight cutting edge for flush trimming and an angled cutting edge for making 22° chamfer cuts. They're for use on countertops and other plastic laminate material.

Choose from bits that cut rounded, cove, wavy, or Roman ogee corners along the edges of your workpiece.

With a ball-bearing pilot and wide cutting wings, these bits cut straight and smooth slots into wood.

These tools create a wide, shallow cut on the face of the workpiece. They're often used to level spoilboard so it lies perfectly flat for accurate routing and milling.