Use these sleeves with compression nuts and fittings to create a strong seal on copper tubing.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

These fittings include a nut with a built-in sleeve, so there’s no need to remove the nut for assembly.

No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They are also known as refrigeration and SAE fittings.

The flared end of the fitting nests inside the fitting body, providing extra support to the tubing. Fittings are also known as inverted 45° flared fittings.

Also known as JIC (Joint Industrial Council) fittings, these connect to tubing that is flared to 37°. They can handle higher pressures than 45° flared fittings.

Use these fittings to make leak-resistant connections without threading or soldering. Slide them over tubing and turn the end nuts to compress the gasket.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

For applications that require an extra level of cleanliness, these fittings are individually bagged to prevent contamination.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Use these sleeves with compression nuts and fittings to create a strong seal on stainless steel tubing.

Instead of a metal sleeve (ferrule), these fittings have a rubber sleeve that cushions tubing and absorbs vibration to maintain a tight seal, even when connected to large pumps.

The thick walls of these fittings can withstand more than twice the pressure of standard compression fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

The male pipe threads on these fittings have a sealant applied for extra protection against leaks.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

Polished to a 15 Ra and under finish, these fittings have a mirror smooth interior. They are also known as ultra-high-purity fittings.

Fittings are polished to a32 Ra and under finish on the interior.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal.

Use these sleeves with compression nuts and fittings, sometimes called bite fittings, to create a strong seal on steel tubing. They are also known as ferrules.

Pair these nuts with compression sleeves and high-pressure fittings. They withstand about twice as much pressure as nuts for standard compression fittings, so they’re good for hydraulic power applications.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

Use these sleeves with a nut and fitting to provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

The external hex bolt on these fittings allows for easy installation in cramped spaces.

Repair pinholes, punctures, and cracks in low-pressure systems with these clamps. Insert tubing into the clamp and tighten the bolts to create a secure seal.

A tube adapter sits flush against the flat face of the fitting so you can slide the steel tubing and fitting sideways to disconnect in cramped spaces. Also known as zero-clearance fittings.

With the best corrosion resistance of any metal fitting we offer, these Hastelloy fittings will stand up to aggressive chemicals and are resistant to pitting and stress cracking. Also known as instrumentation fittings, they include a nut with two sleeves.

A single sleeve (ferrule) compresses the tubing as you tighten the nut on these fittings, creating a strong seal. They are brass for good corrosion resistance.

Use these sleeves with brass compression nuts and fittings to create a seal on plastic and rubber tubing.

Use these O-rings with brass compression tube fittings that have BSPP male threads. They create a seal on the BSPP male threads to guard against leaks.

These fittings include a nut with a built-in sleeve (ferrule), so there’s no need to remove the nut for assembly.

Tube supports slip inside tubing to prevent the walls from collapsing.

These compression tube fittings meet Department of Transportation FMVSS 571 safety standards for air brake lines.

Lighter in weight than their metal counterparts, these compression fittings are polypropylene.

Tube supports slip inside tubing to prevent the walls from collapsing.

Use these nuts with plastic compression fittings to create a seal on plastic tubing. They're moisture-resistant acetal, so they won't absorb water and soften, even in high-humidity environments.

Lighter in weight than metal quick-disconnect couplings, these couplings are plastic.

Fittings have a sleeve that bites into tubing as you tighten the nut to form a seal in applications up to 120 psi. Also known as flareless fittings.

Made of PVDF (also known as Kynar), these fittings have excellent strength and can handle temperatures as high as 240° F or 270° F.

Tube supports slip inside tubing to prevent the walls from collapsing.

Use these nuts and sleeves with compression fittings for food and beverage to create a seal on plastic tubing.

Made of stainless steel, these fittings are more durable than plastic barbed tube fittings for food and beverage.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.