Our most sensitive limit switches, these switches actuate with the slightest push for a high degree of accuracy.

Sealed actuators prevent these switches from jamming, even when exposed to oil, sand, mud, or ice.

Rugged enough for mining operations, these limit switches require a high actuation force, like heavy rocks moving on a conveyor.

Start or stop equipment after a set number of rotations to avoid over-rotation.

Protect machinery and ensure the safety of personnel—these switches will open the circuit when actuated even if a spring fails or the contacts stick.

Stack these slim switches together, or fit them into tight spaces. They're rated IP67 for protection from temporary submersion.

Secure these switches into panel cutouts using mounting nuts. They have a slim body so they can also be stacked together or fit into tight spaces.

Open and close circuits in a snap—even in harsh conditions. With a rubber-encased housing and stainless steel bracket, these switches handle high vibrations and resist corrosion. They’re rated IP68 for protection from dust and temporary submersion.

Enclosures protect these snap-acting switches from the environment.

Rated NEMA 4 , these enclosed switches have a sealed actuator for protection from washdowns.

At least 25% smaller than our Miniature Snap-Acting Switches, these switches are often used to trigger actions from inside a vehicle’s door or an engine compartment.

Built for tight spaces exposed to water, these switches have a housing that's less than 1" long and IP67 rated for protection from temporary submersion.

Smaller than standard snap-acting switches, these switches trigger actions in tight spaces. They’re used in components as small as computer mice and engine restart switches.

Replace the hinges on access doors or machine guards with these switches to keep your team safe from active machinery.

Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.

Block access to machinery while it's running. These safety switches link to a single actuator, so no other RFID tag or card can interfere.

Sized for 4 mm or 6 mm panel cutouts, these switches are often used with circuit boards to control electronics.

A quick push is all it takes to actuate these switches.

A housing seals in anything that could ignite flammable material, so you can use these switches where explosive gas, dust, and fibers may be. They actuate with a quick push.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Install in 8 mm dia. cutouts.

Actuate these switches with a quick push.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

Actuate these switches with a quick push. A housing seals in anything that could ignite flammable material, so you can use them where ignitable gas and dust may be present.

Install in 16 mm dia. cutouts.

Change the cover on these switches without replacing them entirely—they come with seven snap-on covers in different colors. The colors help you quickly identify switches without labels.

Save space on a panel by using one switch to perform multiple switching functions.

Install in 14 mm dia. cutouts.

Often used to trigger alarms, these switches have a recessed button to prevent accidental activation. Mount under desks or in other discrete locations to avoid drawing attention.

Keep a switch within reach—but not in the way. These mount to the underside of desks, tables, and shelves to keep work surfaces clear and reduce the risk of accidental presses.

A lightweight yet durable alternative to stainless steel enclosed switches, these aluminum enclosed switches withstand corrosion, oil, and washdowns.

With a smaller footprint than other switch mats, these fit in confined spaces.

Customize the length of these switches by cutting them from a 25-foot roll.

Step on these mats to control doors, lights, or alarms.

Made with stainless steel conductors, these switches resist corrosion in damp areas. They’re less than 1/4” thick, so they’ll fit under floor mats and in other tight spaces.

Customize the length of these switches by cutting them from a 50-foot roll.

Control machinery from a safe distance, or use these switches as call buttons.

Control cranes and other mobile machinery in dirty, outdoor, and wet environments without damaging your switch.

A durable rubber housing covers the buttons and protects these switches from impact.

Never worry about your pendant switch losing power. These pendant switches generate enough power from pushing the button to send a signal to a receiver up to 330 feet away.

Keep your hands free for other tasks by triggering switches with your foot.

Rated NEMA 6P and IP68, these switches are protected against washdowns, corrosion, and temporary submersion.

Control equipment from up to 40 feet away—these switches include a transmitter and a receiver that connects to equipment.

Step on these switches for hands-free actuation in an area with frequent washdowns.

A rubber seal protects these switches from splashing water.

Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.

Built into a terminal block, these switches mount to DIN rail.

Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.

Designed for use near ignitable gases, fibers, and dust, these switches have a housing that seals in anything that could ignite flammable material. They require a key to turn circuits on or off, preventing accidental activation and limiting access.

These switches are protected from corrosion, high-temperature and high-pressure washdowns, and oil/coolant spraying. Install them in 22 mm dia. cutouts.

Grip and twist a lever to turn these switches on or off—they’re designed to prevent accidental actuation. Install them into standard-sized panel cutouts.

Avoid accidental actuation—these switches won’t turn on or off until you grip and twist the lever. Install in a 16 mm dia. cutout.

Choose an actuator and contact block to make your own 22 mm plastic switch.

Choose an actuator and contact block to make your own 22 mm metal switch.

The wide surface of these switches makes them easy to press on and off, even if your hands are full and you need to use an elbow.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment.

Wire contacts to an alarm system to alert when doors or windows are opened.

Prevent unauthorized use of doors or windows with a combination of coded magnets and contacts that wire to an alarm system.

Prevent unauthorized use—these switches require coded magnets to actuate. They cannot be bypassed using ordinary magnets.

Send signals in response to changing magnetic fields to trigger processes or monitor position, speed, and current.