For Use With For Use With |
|---|
|
Mixing Ratio Mixing Ratio |
|---|
|
Mount Type Mount Type |
|---|
|
Maximum Pressure Maximum Pressure |
|---|
|
Power Source Power Source |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Housing Material Housing Material |
|---|
|
Pump Type Pump Type |
|---|
|
Length Length |
|---|
|
Inlet Thread Type Inlet Thread Type |
|---|
|
Adjustment Type Adjustment Type |
|---|
|
Outlet Connection Style Outlet Connection Style |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
For Container Capacity For Container Capacity |
|---|
|
Discharge Gender Discharge Gender |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
For Use On For Use On |
|---|
|
Aluminum Proportional Mixers for Coolant and Soluble Oil
Use this mixer to dilute coolants and soluble oils with water. It dispenses solution directly from your drum in a measured ratio. Attach your water line to the inlet and set your desired mixing ratio with the regulator knob. The water line connection has a quarter-turn shutoff valve.
Inlet | Outlet | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mixing Ratio | For Container Cap., gal. | For Drum Opening Size | Flow Rate, gpm | Pipe Size | Thread Type | Gender | Min. Pressure, psi | For Tube ID | Tube Connection Type | Max. Pressure | Max. Temp., °F | Each | |
| 8:1 to 100:1 | 5-55 | 2 NPS | 4 | 1/2 | NPT | Female | 15 | 1/2" | Push to Connect | 57 psi @ 70° F | 140° | 000000 | 0000000 |
Bronze Proportional Mixers for Coolant and Soluble Oil
Use these mixers to dilute coolants and soluble oils with water. They dispense solution directly from your drum in a measured ratio. Attach your water line to the inlet and set your desired mixing ratio with the needle valve. The water line connection has a quarter-turn shutoff valve.
Inlet | Outlet | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mixing Ratio | For Container Cap., gal. | For Drum Opening Size | Flow Rate, gpm | Pipe Size | Thread Type | Gender | Min. Pressure, psi | Pipe Size | Thread Type | Gender | Max. Pressure | Max. Temp., °F | Each | |
| 15:1 to 45:1 | 5-55 | 2 NPT | 3 | 3/8 | NPT | Female | 25 | 1/2 | NPT | Male | 75 psi @ 70° F | 150° | 000000 | 0000000 |
| 4:1 to 35:1 | 5-55 | 2 NPT | 3 | 3/8 | NPT | Female | 25 | 1/2 | NPT | Male | 75 psi @ 70° F | 150° | 000000 | 000000 |
Water Aspirator Pumps
Pick up chemical spills and remove liquids in vacuum filtering systems—these pumps create suction to draw up liquids and gases as water flows through them. They’re made of HDPE and polyethylene, so they won’t break down when exposed to highly corrosive chemicals and acids. The suction end has a barbed tube connector, which attaches to your vacuum tubing. The connector stays attached to your vacuum tubing and connects to the pump when you’re ready to use it again. These pumps also have an internal check valve to prevent backflow.
Suction | Intake | Discharge | Overall | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Flow Rate, gpm | Maximum Vacuum, in. of Hg | Minimum Operating Pressure, psi | Temperature Range, °F | For Tube ID | Gender | Pipe Size | Thread Type | Gender | Outlet Connection Type | Gender | Length | Width | Includes | Each | |
| 1.5 | 27 | 11 | -140° to 240° | 1/4", 5/16", 3/8" | Male | 3/8 | NPT | Male | Open | Female | 3" | 3" | 4 1/2" Length of 3/8" OD Polyethylene Tubing | 00000000 | 000000 |