A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Keep material from coming in contact with the mounting surface without the need for a spacer.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Cut as much strap as you need to hang duct, pipe, and other materials.

A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.