For light duty applications, choose these metric-sized coupling nuts.

Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.

Made from Grade 8 steel, these nuts are about 25% stronger than medium-strength steel coupling nuts. Furnished in inch thread sizes.

Comparable in strength to Grade 9 bolts, these coupling nuts are about 20% stronger than high-strength steel coupling nuts. Available in inch thread sizes.

These metric coupling nuts have good chemical resistance.

More corrosion resistant than 18-8 stainless steel coupling nuts, these metric nuts have excellent resistance to chemicals and salt water.

Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.

Known for their strength, steel coupling nuts are available with a corrosion-resistant finish.

A smooth rounded body provides a finished look.

Choose these standoffs for their adherence to NAS 1831 specifications.

These standoffs are made to NAS specifications.

Protect components from electrical charges.

With the end clinched in place, the prongs allow you to quickly snap a panel on and off these supports.

The flat top supports boards without drilling a hole while wings on the other end add tension for a secure hold in a hole.

Designed for multi-level printed circuit board applications, these self-aligning, through-hole supports have a chamfered female end for stacking. The other end snaps and locks in place for a permanent connection.

The ends of these removable supports snap in and compress between panels to reduce vibration of miniature cooling fans in compact electronics.

Wings add tension to strengthen the hold in a hole. The other end is releasable for repairs and upgrades.

Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Need to join two female-threaded parts, such as coupling nuts, with dissimilar inch thread sizes? Attach them to these adapters and tighten the exterior hex nut for a secure connection.

Twist these adapters onto female metric threads to change pitch or switch thread sizes.

One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.

Join two female-threaded parts of various thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Made of stainless steel for excellent corrosion resistance, these nuts make pivoting and hinge movements where misalignment is not a concern.

Use these nuts with compression sleeves and fittings to create a strong seal on stainless steel tubing.

Pair these nuts with compression sleeves and high-pressure fittings. They withstand about twice as much pressure as nuts for standard compression fittings, so they’re good for hydraulic power applications.

Use these nuts with plastic compression fittings to create a seal on plastic tubing. They're moisture-resistant acetal, so they won't absorb water and soften, even in high-humidity environments.

Use these nuts and sleeves with compression fittings for food and beverage to create a seal on plastic tubing.

Also known as CGA nuts, these are designed for low-pressure welding applications downstream of your pressure regulator. Attach them to barbed hose fittings for compressed gas to make a threaded connection to torches or pressure regulators.

Used in low-pressure pipe lines, these brass fittings have a plating that makes them shiny and improves corrosion resistance.

Use these corrosion-resistant fittings in a low-pressure pipe line.

The galvanized finish on these fittings provides fair corrosion resistance. Fittings are for use in low-pressure applications.

Use these fittings for low-pressure applications in noncorrosive environments.

Secure threaded plastic conduit fittings to a knockout in an outlet box or enclosure.