Mount these terminals on a threaded screw or stud for a more secure connection than spade and hook terminals.

Mount these elongated ring terminals on a range of screw sizes.

A plastic cover on the barrel provides electrical insulation. These terminals can withstand temperatures up to 300°F.

When heat is applied, the enclosed solder melts, creating the most secure, electrically conductive, and environmentally sealed connection we offer.

A plastic cover on the barrel provides electrical insulation rated to 600 volts.

A serrated edge on the inside of the ring grips the mounting screw for a secure hold.

Connect wire to a screw or stud at a right angle to fit connections into tight spaces.

A plastic cover on the barrel provides electrical insulation.

Easy to install, connect, and disconnect, yet difficult to shake loose. These terminals interlock with each other to make a secure connection.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

Rated UL 94 V-0 for flame resistance, these terminals are made of flame-retardant, self-extinguishing material to reduce the risk of fire.

Rated UL 94 V-0 for flame resistance, these terminals are made of flame-retardant, self-extinguishing material to reduce the risk of fire.

A plastic cover on the barrel provides electrical insulation.

Add strength and stability to stranded wire to protect it from damage and speed insertion into terminal blocks.

Loosen your mounting screw to install—the open end eliminates the need to completely remove it.

When heat is applied, the enclosed solder melts and the insulation shrinks, creating the most secure, electrically conductive, and environmentally sealed connection we offer.

Connect wire to a screw or stud at a right angle to fit connections into tight spaces.

These solid pins make it easier to insert stranded wire into screw-clamp connections.

Also known as bullet terminals, these have a round tab that requires less space than the flat tab found on most quick-disconnect terminals.

A plastic cover on the barrel provides electrical insulation rated to 600 volts.

A plastic cover fully insulates these splices.

Visually confirm your connection through the inspection window in the insulation of these splices.

The most secure, electrically conductive, and environmentally sealed connection we offer, these splices have enclosed solder that melts when heat is applied.

Able to withstand temperatures up to 900°F, these splices are suitable for use in high-heat applications such as ovens, motors, and light fixtures.

Filled with grease, these splices resist moisture and corrosion.

A plastic cover fully insulates these splices.

These splices can withstand higher temperatures than insulated splices.

Compress the barrel twice on each end for an extra-tight grip in high-vibration applications.

Pierce the insulation of wire without stripping it to make quick connections that are also sealed to keep out water.

Twist stripped wires together, insert them into the connector, and then crimp for a dependable connection.

When heat is applied, adhesive-lined insulation shrinks and bonds to the wires, creating a moisture- and corrosion-resistant seal.

Connect one wire to two wires of the same size. When heat is applied, adhesive-lined insulation shrinks and bonds to the wires, creating a moisture- and corrosion-resistant seal.

Filled with gel, these wire taps seal out moisture.

Tap a main wire or add a finished terminal to the end of a wire.

No crimping or wire stripping needed—this assortment includes twist-on wire connectors and insulation-piercing wire taps.

Keep a variety of male/female pairs of quick-disconnect terminals on hand.

Compress the barrel twice for an extra-tight grip in high-vibration applications.

Use these sleeves for non-lifting applications such as tethering, securing, and suspending.

Also known as socket-end swage fittings, install these ball-with-shank-end fittings with a roller swage press for a strong, permanent hold.

Also known as socket-end swage fittings, install these stud-end fittings with a roller swage press for a strong, permanent hold.

Compress sleeves with less effort than standard compression tools.