Two layers of fiberglass mesh reinforcement give these wheels at least three times the life of standard cutoff wheels when cutting metal such as aluminum, iron, stainless steel, and steel.

These high-density ceramic oxide wheels have two layers of fiberglass mesh reinforcement and last up to twice as long as long-life cutoff wheels when cutting aluminum, iron, stainless steel, and steel.

For quick cuts in stainless steel, run these high-density zirconia alumina wheels at a higher rpm than standard cutoff wheels.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts in aluminum, iron, stainless steel, and steel.

Switch between cutting and deburring aluminum, iron, stainless steel, and steel without the need to change your wheel.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Made of a combination of ceramic alumina and zirconia alumina, these wheels last up to ten times longer than standard cutoff wheels when cutting hard metal such as Inconel, Hastelloy, and tool steel.

An extra-fine layer of fiberglass mesh reinforcement allows these wheels to make smoother cuts than standard bench-grinder cutoff wheels when cutting metal such as aluminum, iron, stainless steel, and steel.

Make fast, burr-free cuts in stainless steel with these premium aluminum oxide wheels.

Use these clog-resistant wheels to make quick cuts in soft metal such as aluminum, brass, and copper.

Make cuts in hard, brittle materials such as firebrick, stone, and concrete.

These wheels have a zirconia alumina abrasive for cutting ductile cast iron.

Designed to cut sheet metal.

These wheels have a blend of aluminum oxide and silicon carbide abrasives for cutting ductile cast iron.

Made of diamond abrasive, these wheels cut ceramics, tile, and other abrasive materials.

Use these wheels for cutting soft metal, plastic, stone, and wood.

Make cuts in most metal, including aluminum, iron, stainless steel, and steel.

Cut plastic, wood, and soft metal such as aluminum, brass, and copper.

The segmented edge on these blades is coated with diamond grit for cutting plastic.

The edge of the blade is segmented to cut faster than a continuous edge.

The edge of the blade is segmented to cut faster than a continuous edge.

A blend of tungsten carbide and diamond grits on the continuous edge of these blades cuts hard, nonmetallic materials including composites and graphite.

Use these blades with water or coolant to produce smoother cuts in tile than dry-cutting blades. They're also for use on glass.

Also known as dado-head blades, these are for cutting grooves in all types of wood.

Use these blades for occasional cutting.

Produce smooth cuts in plastic materials including polycarbonate, polyurethane, PVC, and acrylic with the carbide-tipped teeth on this blade.

Cut stainless steel sheets, pipe, tubing, and grating with teeth made of impact-resistant carbide.

Prevent clogging when cutting soft metal—these blades have plenty of space between the carbide-tipped teeth to allow chips to escape.

Cut stainless steel sheets, pipe, tubing, and grating with teeth made of impact-resistant carbide.

Diamond grit bonded to a segmented edge cuts through hard metal such as cast iron.

Also known as rip blades, these steel blades have large, forward-angled, carbide-tipped teeth for making fast cuts.

A continuous edge on these blades produces smooth cuts.

The edge of the blade is segmented to cut faster than a continuous edge.

Use these blades for occasional cutting.

Cut wood, plywood, and particleboard.

A blend of tungsten carbide and diamond grits on the continuous edge of this blade cuts hard, nonmetallic materials including composites and graphite.

Make clean cuts in rubber and plastic hose with the scalloped knife edge on these blades.

The blade edge is coated in diamond grit.

Blades and teeth are steel and treated to a Rockwell Hardness between C63 and C65 for increased wear resistance when cutting through steel and cast iron bars, rods, pipe, and tubing.

A higher air consumption rating allows this saw to work in longer bursts than the light duty air-powered portable cutoff saw. It has a durable composite handle.

This saw is less than half the weight with a smaller wheel diameter than standard bench-top cutoff saws.

A high-torque motor powers these saws through tough metal, such as angle iron and tool steel. These saws must be hardwired.

Operate this saw at a low rpm to make quick cuts in metal without excessive heat or the need for coolant.

Pair these holders with a tool block for right- and left-hand mounting in a lathe.

Mount blade-style holders to a lathe tool post or turret.

Pair these holders with a tool block for right- and left-hand mounting in a lathe.

The rounded nose on these inserts contours the outside of the workpiece and cuts grooves with rounded edges.

A thinner cutting edge and thicker top edge give these blades a T-shape profile that moves chips away from the cut and reduces friction for fast cutting.

A carbide tip brazed onto a ground steel shank makes these tools more wear resistant than high-speed steel tools.

Made of solid carbide, these saws are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material. Use them for cutoff, slitting, and slotting applications.

With peripheral and side teeth, these saws remove chips for a consistent cutting width.

Attach cutoff wheels to a Dremel grinder.

Mount cutoff wheels, grinding wheels, and other abrasive discs to the straight shaft on bench-top motors, grinders, and buffers.

A nickel-coated diamond grit and synthetic resin bond make these wheels extremely hard and wear resistant.

Two slide-in dovetail mounts on the tool posts allow you to quickly change from one tool holder to another.

Commonly used with hydronic heaters, this thermostat senses the temperature of liquids. The thermowell protects the sensor.

Control one- and two-speed heaters and air conditioners.

Regulate line-voltage HVAC systems.

Use to regulate line-voltage HVAC systems where flammable gases, vapors, and dust are present. Thermostats are rated Class I, Divisions 1 and 2, Groups C and D; and Class II, Divisions 1 and 2, Groups E, F, and G.

Place sensor in enclosures or different rooms than the rest of the thermostat to control temperature from outside the space.

Set these thermostats to adjust the temperature at certain times each day.

Control a single heating or cooling device in your enclosure to keep electronics at a safe operating temperature.

These thermostats work with low-voltage HVAC systems that have only one speed.

Keep electronics in your enclosure from getting too hot or cold with these thermostats that control two devices at once.