Push your door open to automatically engage the holder; pull on the door to release.

Latch your door to the wall for a secure hold.

Step on the spring-operated plunger to hold your door in place; tap on the release lever to free it.

Hold doors open within the 85° to 110° range without adding clutter to your floor or walls.

Latch your door to the floor for a secure hold.

A magnet holds the door open; pull on the door to release.

Small enough to slip into a pocket, these foldable wedges are good for workers who frequently need to prop doors open as they move from job to job. Slide them under the door to hold it open.

For frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

To protect doors and walls, these closers have a shock-absorbing stop to damp the force of doors when they’re pushed open. Designed for frequently used doors, these last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

There's no need to mount a closer to your door or frame—these take the place of an existing hinge pin.

No need to drill new holes—these closers have a mounting plate that fits the hole patterns of most closers from Norton, LCN, Yale, Corbin Russwin, and Dorma.

When replacing door closers, these mounting plates let you match new closers to your existing hole patterns from most Corbin Russwin, Dorma, LCN, Norton, and Yale closers.

Hardwire these switches to automatic door openers, electromagnetic locks, and electric strikes and your door will open at the touch of a button or the wave of your hand.

These closers include a door holder, which keeps doors open with an electromagnet. When activated by a fire alarm, the magnet shuts off and releases the door.

Mounted diagonally so one end is higher than the other, the motion of an opening door tightens the torsion spring; as it unwinds, it closes the door.

Springs retract to pull storm doors and gates closed.

Close storm doors more smoothly than standard spring closers.

With a hydraulic mechanism, these are the smoothest and quietest closers we offer for gates.

Also known as jackshafts, these openers operate 24-ga. or thinner overhead doors.

Use a smartphone or computer to control up to 16 Liftmaster automatic overhead door openers that are MyQ-enabled. Download the free MyQ mobile app to track activity and operate your doors remotely.

Conveniently carry your transmitter with your keys to remotely operate automatic overhead door openers.

Requiring less space to mount and operate, these supports are often used on small cabinets and enclosures. They gradually slow your lid's motion to prevent it from slamming open. To open lids, lower them and the support will slowly and softly do the rest. Manually shut the lids and the supports will hold them in the closed position.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Also known as hatch springs, these supports are commonly used on hatches and other top-opening lids. Raise the lid to extend the spring, which props the lid open—an internal cable keeps the spring from overextending. Press the center of the spring to release the hold and close the lid.

To eliminate slamming and smashed fingers, these supports automatically pull lids shut when they approach the closed position. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Commonly used on hood and trunk lids, these simple, three-piece rods telescope from 18 1/2" to 46 3/4" to prop lids open at a variety of angles.

Use these openers on casement windows.

Mount these balancers in the corner of a horizontal frame to suspend, lift, or lower objects that move vertically in a track such as windows, doors, and panels.

These gas springs have threaded ends so you can use them with any combination of end fittings, studs, and mounting brackets.

With no gas to leak out and a corrosion-resistant 316 stainless steel construction, these mechanical springs are built for long-term, maintenance-free use in wet environments.

These general purpose gas springs assist in opening lids, covers, windows, conveyors, and seats—similar to a hatchback opening on a car.

Release gas from these springs until they supply the exact force you need—made of corrosion-resistant 316 stainless steel, they’re commonly used in wet environments.

Automatically locking when fully extended and made of 316 stainless steel to resist corrosion, these gas springs protect material and equipment underneath heavy loads in damp environments.

Ensure you have the correct force for your application. These gas springs have a bleed valve so you can release gas to permanently reduce the force to meet your requirements.

Sized with short stroke lengths and miniature dimensions, these gas springs are for opening small lids and doors, like those on toolboxes and access panels.

Color coded by force to help you choose the correct replacement, these gas springs generate high force in small spaces.

Made from stainless steel for excellent corrosion resistance in damp environments.

These brackets secure eyelet end fittings from both sides to provide a strong hold on gas springs that get bumped or jostled. Mount on any panel, lid, or door.

Designed to mount at the point of contact between a door handle and the wall, these stops prevent handles from damaging walls when doors swing open.

Designed to withstand impact in high-traffic areas, these stops have an anchor that mounts in a hole and sets with grout. Install them in concrete floors to protect walls from large doors in warehouses and manufacturing areas.

The half-dome shape won't catch mops and scrubbers. Install these stops in wood or concrete floors.

Remove the pin on your door's hinge, slide it through one of these stops, and then insert it back into the hinge to set and adjust the door's opening angle.

Protect door knobs and other hardware from damage caused by carts, dollies, and other equipment.

Protect large swinging doors where carts and vehicles are used to push the door open. These polyethylene plastic bumpers are commonly used on two-way swinging doors.