Made of EPDM foam rubber, these seals have hollow construction for more compressibility than solid seals.

Hollow construction makes these seals more compressible than solid rubber seals. Made of EPDM rubber, they also resist salts.

These solid EPDM rubber seals also resist salts.

The hollow construction on these seals provides better compressibility than solid rubber seals. Made of silicone rubber, they also resist water and salts.

It’s the hollow construction that makes these seals more compressible than solid seals. Made of silicone foam rubber, they also resist water and salts.

In addition to oil, these seals resist grease, salts, water, steam, and most detergents.

These seals have a solid bulb.

These seals have an EPDM foam rubber bulb.

The EPDM rubber wiper is firmer and more durable than the EPDM foam rubber wipers.

Made of silicone rubber, these seals can handle temperatures up to 500° F, plus they resist water and salts.

Use these H-seals to lock out moisture, dust, and debris around windows and panels.

Hollow construction on these vinyl rubber seals provides better compressibility than seals with a foam core. They also resist salts and detergents.

The foam core makes these vinyl rubber seals firmer and more durable than hollow seals. They also resist salts and detergents.

These seals have solid construction.

These seals have solid construction.

Able to withstand temperatures up to 1000° F, these seals have a fiberglass cover and core that resists most refrigerants, salts, and grease.

A silicone-coated fiberglass cover sheds sparks and molten metal splash. These seals resist steam, most refrigerants, salts, and grease. They can withstand temperatures up to 450° F.

A ceramic cover makes these seals more chemical resistant than the seals with a silica cover. They resist acids (except hydrofluoric and phosphoric), diluted alkalies, most refrigerants, salts, and grease. Seals can withstand temperatures up to 1700° F.

These loosely knitted fiberglass seals are more flexible, compressible, and conformable than High-Temperature Rope Edge Seals.

Made of 96% silica, these seals resist temperatures up to 1800° F.

Made from tightly woven calcium alumina silicate, these seals can handle temperatures from –300° to 1100° F.

For a tight fit, the seal projection can be adjusted.

A dense seal helps control noise.

Flexible pile construction helps reduce door vibration.

Also known as door sweeps, this weatherstripping closes the gap between the bottom of the door and the floor.

A drip guard diverts rain and snow away from the bottom of the door.

Avoid scuffing your floor and reduce wear on your seals—this weatherstripping has a plunger that lowers the seal as the door is closed and raises it as the door is opened.

Sets include six pieces of weatherstripping for an overhead door—two for the top and four for the sides to seal gaps.

Close the gap between the bottom of an overhead door and the floor.

The threshold height can be adjusted to ensure a tight fit under a door.

With a ribbed top, these thresholds offer more slip resistance than smooth-top thresholds.

The middle of these three-piece thresholds can be installed smooth or ribbed side up for more slip resistance.

To provide more protection from the elements than dock door seals, these shelters wrap around trailers.

Create a frosted effect on windows to block the view.

Once heated, this film creates a tight seal around windows to prevent drafts.

Made of rubber, this trim resists abrasion better than plastic trim. Often used on panels, boards, signs, and mirrors, it protects edges from impact.

Sample multiple sizes and styles of rubber trim.

A metal core adds strength and stability, making this trim more durable than other high-temperature rubber trim. It withstands temperatures up to 400° F, which is generally twice as high as our standard rubber trim. Use it to protect the edges of panels, boards, and signs from impact. Made of rubber, it resists abrasion better than plastic trim.

This trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of rubber, it resists abrasion better than plastic trim. Use it to protect the edges of electronics equipment and circuit boards from impact.

Sample multiple sizes and styles of heavy duty plastic trim.

This trim withstands temperatures up to 500° F, which is generally twice as high as our other slippery trim. With a slippery surface, it minimizes friction between parts and is often used on conveyor rails, chutes, and guides. Made of plastic, it's also chemical resistant.

This trim meets FMVSS-302 for Federal Motor Vehicle Safety Standards for flammability, UL 94 HB flame requirements, and NFPA (National Fire Protection Agency) standards. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, and signs from impact.

With a surface resistivity of 10 ⁵ ohms this trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of plastic, it's also chemical resistant. Use it to protect the edges of of electronics equipment and circuit boards from impact.

Black and yellow stripes create a visual alert to draw attention to equipment and obstructions. Designed to cushion during impact, this foam trim protects edges on posts, shelving, and other surfaces from damage.

Made of aluminum or stainless steel, this trim withstands heavy impact for maximum surface protection. It's often used on panels, boards, signs, and mirrors to protect the edges.

Cushioning on the top provides added protection from impact. This nylon-coated stainless steel trim combines strength with flexibility for a snug hold. It can also protect wire, cable, and hose.

The raised bulb adds cushioning to absorb more impact than other surface guards to protect walls and other flat surfaces from impact.

Vibrant colors create a visual alert to draw attention to equipment and obstructions. These guards protect walls and other flat surfaces from impact.

These metal guards provide more impact protection than plastic guards. Commonly used in warehouse and manufacturing areas, they protect corners on walls and other surfaces from impact.

With a raised bulb to absorb greater impact than standard corner guards, these guards protect walls, cabinets, and other surfaces.

The guards in this system have a metal core for added strength and stability. Combine corner guards and surface guards to create a system that protects walls and equipment from impact and wear. Often used in warehouse and manufacturing areas, these systems protect against damage from carts and vehicles.

Reinforce the edge of a door to guard it against damage from foot traffic and equipment. These plates can also be used to salvage rusted, rotted, or otherwise damaged doors.

Easily attach, move, and replace these magnetic wear strips on metal surfaces to minimize friction—simply press them on and peel them off as needed. Often found on conveyor systems and chutes, use these strips where friction between two parts or materials is wearing down equipment to extend equipment life.

Impact causes these porous bronze plates to release a thin layer of oil on the surface to minimize friction. Often found on conveyor systems and fabricating machinery, use these plates where friction between two parts or materials is wearing down equipment to extend equipment life.

Made of woven polyethylene fabric, this is the most puncture-, abrasion-, and tear-resistant surface protection we offer. Commonly used on heavy equipment, it guards metal, plastic, composite, and painted surfaces from damage. It can also be used as a protective layer beneath other materials.

Press this optically clear film into place on windows, mirrors, and glass surfaces. When one layer gets scratched or marred, peel it away to expose a new layer.

Often used to protect sheet metal during fiber and CO2 laser cutting, this film is also good for other fabrication processes such as bending, stamping, and forming. You can even leave this film on finished parts for protection against damage during shipping and storage.

These aluminum bases provide more impact protection than plastic bases. In addition to protecting the bottom of a wall from damage, they create a finished look where the wall meets the floor. They're commonly used in warehouse and manufacturing areas.

EPDM is blended with neoprene and SBR to create a general-purpose foam that offers good resistance to water and wear.

In addition to having good resistance to water, sunlight, and oxidation, these neoprene foam sheets and strips resist swelling when they come into contact with oil.

These vinyl foam sheets and strips are so conformable that once they're compressed they won't fully spring back. Use them to fill gaps and seal uneven surfaces.

This premium silicone is the most resilient foam we offer. It is equivalent to Cohrlastic and is also known as Norseal and silicone sponge.

One layer of fiberglass fabric is sandwiched between layers of silicone foam giving these strips strength to handle high-stress applications, such as gasketing.

Prevent the spread of flames with these self-extinguishing silicone foam sheets and strips.

A thin layer of aluminized fiberglass on this silicone foam reflects heat to protect sensitive equipment.

Made from a blend of Buna-N, neoprene, and vinyl, these foam strips have good resistance to oil.

Press this adhesive-backed plastic tape into place for an immediate light-duty seal.

Resistant to mold and mildew, these sealants are well suited to high-humidity environments.

These sealants include a material certificate with traceable lot number, test report, and product shelf life.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete.

Apply these sealants in cold temperatures, on wet surfaces, and even through running water.

With chemical and metal additives that are picked up by X-ray machines and metal detectors, these sealants are designed to help you comply with Hazard Analysis and Critical Control Point (HACCP) programs in food-processing facilities.

Also known as neutral cure, this sealant won't discolor copper, brass, plastic, and concrete.

Apply these sealants in cold temperatures, on wet surfaces, and even through running water.

These non-sagging sealants will not drip while hardening on vertical and overhead surfaces.

Impervious to the swelling effects of oil, fuel, and solvents, use these high-strength sealants to assemble and repair fuel systems and tanks.

These sealants are marine grade, so they stand up to water, corrosion from salt spray, mildew, and UV light.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Sunlight, ozone, and water won’t affect these sheets and strips.

Often used as inner tubes, butyl rubber won’t allow air, fumes, or gases to pass through.

One layer of fiberglass cloth is inserted between two layers of silicone rubber to give these sheets and strips the strength to stand up to high stress and flex. Use them as flange gaskets and anywhere heavy compression would squeeze nonreinforced silicone rubber out of place.