These sink drains have an overflow cutout.

Prevent sewer gas from entering your building. Traps swivel and adjust vertically for convenient installation.

Use these J-bends as replacement parts for P-traps and S-traps.

Use these extensions to help connect drain tailpieces to drain traps.

This drain is chemical resistant and often used in lab sinks. The P-trap prevents vapors from returning up through the drain.

These grates are strong enough to handle a high volume of traffic, even from vehicles.

Bolt two same-size flanges together with a gasket to create an access point within a line. Also known as Schedule 40 flanges, they are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

The snap-together design allows you to quickly connect these fittings to pipe with no cement required. Fittings are typically used in gravity-flow drainage applications.

This pipe has thinner walls than Schedule 40 pipe, so it’s lighter in weight and has more space on the inside for high-flow applications, such as underground gravity-flow sewer and storm drainage lines.

Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

Made of polypropylene, these fittings won’t deteriorate when exposed to the damaging effects of ultraviolet light and are suitable to use outdoors. They have the chemical resistance to withstand acids, solvents, and other harsh substances.

These fittings are an economical option for chemical waste systems. Fittings are ABS plastic, which has excellent strength and impact resistance and good chemical resistance.

These fittings are NSF certified for use in corrosive waste gravity-flow systems. Made of CPVC, they have better chemical resistance than ABS plastic gravity-flow fittings and can stand up to highly-corrosive acids and other harsh substances.

Made of corrosion-resistant plastic, these fittings won’t deteriorate when used in oil applications. They have high strength and impact resistance.

Access the inside of lines operating up to 285 psi, so you can vent pressure, drain liquid, or take samples. Made of black-coated steel, these bleed rings should be used in dry environments to prevent rusting.

Create an access point in systems operating up to 230 psi where corrosion is a concern. Made of stainless steel, these bleed rings resist rusting.

These withstand at least double the pressure of our other timer-operated drain valves.

Able to withstand up to 400 psi, these have the highest pressure rating of all our float-operated drain valves.

Keep an eye on condensate collecting in your compressed air line. These drain valves have a clear bowl, so you can see inside to inspect the contents.

With a discharge capacity of more than four gallons per minute, these drain valves can handle large compressed air systems.

Save energy by minimizing the loss of compressed air. Unlike other drain valves, these only open when they’re full. They close before the reservoir is completely empty, so no air escapes from the system.

When water is condensed out of a compressed air system, it contains oil from the compressor that makes disposal difficult. These separators use two-stage filtration to reduce oil content to below 20 parts per million.

The large knob makes these drainage valves easy to grip.

Safe for use around flammable and combustible gases, vapors, fibers, and dust, these drains let moisture buildup from temperature changes inside enclosures drip out to keep electronics dry.

Safe for use around hazardous gasses and dust, these vents maintain steady pressure and prevent moisture buildup from temperature changes inside enclosures.

These conductive aluminum screens block electromagnetic interference (EMI) and radio frequency interference (RFI) to prevent electrical problems such as radio static and faulty signals. Made of mesh, they let air flow through, so the pressure in your enclosure stays constant as temperatures fluctuate.

Narrow openings give this grating a higher load bearing surface than our standard metal bar grating and reduce the chance of something falling through.

Formulated to protect against odors, stains, and degradation, this grating is often used in food-processing areas.

Narrow openings prevent items from falling through this grating and make it easier for carts to roll across.

Use plank grating for platforms, stair treads, ramps, and decks.

Secure grating to your support structure.

The most economical stair treads we offer.

Openings in the surface allow dust, dirt, and liquids to pass through.

This solid fiberglass grating is good for wheel traffic and areas where you don't want small items and debris to fall through.