Thread these dispensers directly into bearing housings, pumps, and other machinery. Flip the lever to start and stop flow; turn the dial to adjust flow.

A sealed design prevents contamination in dirty and dusty environments.

Customize these dispensers to serve up to 24 lubrication points from a single location.

Serve multiple lubrication points from a single location.

A sealed design prevents contamination in dirty and dusty environments.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Flip the lever to start and stop flow.

Connect these brushes to oil reservoirs and flow adjustment valves to lubricate chain, gears, and conveyors.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

A needle dispensing tip provides fine control for lubricating small parts.

Deliver a mist of oil using shop air.

Add faucets to oil dispensing stations for increased utility.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

Designed for high-pressure instrumentation applications, these valves are rated for up to 10,000 psi and have a hex nut and threads below the handle for panel mounting. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a gauge port on each side of these valves, you can install two different pieces of instrumentation equipment to simultaneously monitor multiple media properties without interrupting flow. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For installation in instrument panels, these valves have a hex nut and threads below the handle. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a low-profile body and a narrow port-to-port length, these valves fit in tight spots. Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a PTFE seal and a PVDF body. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Add fine flow control to tubing lines for oil, butane, diesel fuel, fuel oil, gasoline, kerosene, natural gas, and propane. These valves have a barbed fitting that grips onto tubing, providing a secure hold. Turn the handle to adjust flow in small increments.

With no metal parts, these valves are often used for noncontact flow adjustment in wet conditions and harsh environments. All press down on the outside of tubing to adjust flow without contacting the process media.

Valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Plastic provides a lightweight and corrosion-resistant alternative to metal. Use with oil. These valves gradually open and close to adjust and regulate flow.

To automatically shut off the flow of diesel fuel, fuel oil, kerosene, and oil in case of fire, these valves automatically close and the handle permanently fuses in place when the ambient temperature reaches 165° F.

Rated for twice the pressure of other threaded flow-adjustment valves, these are often used in refineries and other demanding environments. Use with water, oil, air, and inert gas. They gradually open and close to adjust and regulate flow.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

An aluminum body provides strength and durability at half the weight of other metal flanged flow-adjustment valves. These valves are for use with water, oil, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Metal provides more durability than plastic. With seats that can stand up to aggressive and corrosive solutions, these valves are often used in chemical-processing applications. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Unlike other manifolds, which have an inlet on either end, these have one inlet on the opposite side from the outlets. This design allows air or fluid to follow a straight path, improving flow through your system. Also known as headers.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.