The handle is covered in rubber for a comfortable grip.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

When the ratchet head becomes worn or damaged, change it out for a new one.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

No need to pull the socket off the tool—push a button to release.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

Bolts and threaded rod pass through these wrenches when used with bolt-through sockets.

A rubber coating provides a comfortable grip.

Turn sockets from above when there's not room to swing a standard wrench handle.

Bend around obstructions to turn hard-to-reach fasteners.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

These wrenches have an accuracy of ±2.0%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Use these tools for general shop applications.

With sizes from EP10 to EP24, these sets have the sockets you need to install and remove a wide range of External Torx-Plus fasteners. Pair them with a square drive tool, such as a socket wrench, to deliver high levels of torque without slipping.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Set a desired torque within the range.

Use sockets with tools that accept hex shanks, such as impact drivers and power drills.

Quickly position these sockets on square and external 8-point fasteners.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the socket.

Extra-long bits allow access to hard-to-reach fasteners.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

The offset head gives you additional clearance to turn hard-to-reach fasteners.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.

A lever reverses the ratchet direction.

Flip these wrenches over to ratchet in the opposite direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

A lever reverses the ratchet direction.

Suitable for occasional maintenance work, these sets are imported.

Suitable for occasional maintenance work, these sets are imported.

Pivot the box end for access to fasteners in tight spots.

Turn fasteners with the firm grip of a wrench and the adjustability of pliers.

A ratchet mechanism turns fasteners more quickly than a standard bit driver. Insert a bit into the shaft and a magnet holds it in place.

A ratchet mechanism turns fasteners more quickly than a standard driver. These screwdrivers have 90° offset tips to provide additional clearance when reaching over obstructions to turn fasteners.

Attach these adapters to square-drive tools.

Connect these powerful tools to your shop air. They hammer as they rotate to drive screws quickly, even through thick or dense material.

Connect a tap to these wrenches for occasional or light-duty hand tapping. All have a T-handle design, so they're more compact than straight-handle tap wrenches but provide less leverage.

For occasional or light-duty hand tapping, connect a tap to these wrenches. They have long handles to provide more leverage than T-handle wrenches, but they require more space for tapping.

Switch from internal to external threading with interchangeable tap and die adapters. Use them with the included ratcheting wrench.