After extending to full length to provide added reach, this cable retracts and self-coils for tangle-free storage. It's often used with hand tools and other portable devices.

The insulation resists corrosive chemicals and salt water, and the wires in this cable are tin plated for corrosion resistance.

At 0.22" thick, this flat cable has a low profile to fit in tight spaces. The wires are tin-plated for corrosion resistance, and the insulation resists corrosive chemicals and salt water.

For high-heat applications such as furnaces and ovens, this cable's insulation withstands temperatures of 390° F and higher.

Often used in mining equipment, submersible pumps, and drilling rigs, this cable withstands 2,000 volts AC/DC.

Often used to wire pendant switches, this cable hangs from an overhead connection. Also known as bus drop cable.

Also known as zip cord, this cable is often used in lamps, heat guns, and other small appliances.

The insulation has excellent resistance to oil, so this cable can be used near motors. Often used in automated applications, it withstands continuous motion without degrading data or signal transmission

In addition to handling continuous movement, this cable withstands twisting up to 450° without degrading data or signal transmission. It's often used in welding robots and rotary tables.

Connect servocontrollers and servomotors in automated equipment and on assembly lines. This cable withstands continuous motion without degrading data or signal transmission.

For use in tight spaces, this cable has up to a 40% smaller OD than standard continuous-flex cable. It withstands continuous motion without degrading data or signal transmission.

This cable meets TC-ER crush and impact requirements for exposed runs in cable trays, so it can be used without conduit. It sends signal and data to operate, measure, or regulate automated equipment.

Also known as VFD motor cable, this cable is used in variable-frequency drive motors. It has shielding to block signal interference caused by voltage fluctuations and current spikes.

Also known as festoon cable, this flat cable fits in confined spaces such as overhead cranes and hoists. It sends signal and data to operate, measure, or regulate automated equipment.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it in low-current circuits such as intercoms and security systems.

After extending to full length to provide added reach, this cable retracts and self-coils for tangle-free storage. It's often used with low-current circuits such as microphones and headsets.

Rated for in-wall installation, this cable carries power to wall outlets. Also known as branch circuit wire.

Also known as fixture whips, this cable has locknuts and fittings attached to the protective metal armor to secure it to a knockout. It's often used to connect light fixtures.

This cable is approved for use in vertical shafts and large facilities with mulitple levels for critical circuits such as fire alarms and smoke detectors.

Use this cable for complex and high-speed data and signal transmission.

Connect devices such as sensors, programmable logic controllers, and actuators to an automated network.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it to send data between computers, servers, and switches.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. It has an oil-resistant insulation to protect wires as the cable moves from duct to equipment or machinery.

Hook up speakers, intercoms, and other low-current devices to a building's communication wiring.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it to transmit audio, video, and data signals.

Approved for flame resistance, this cable meets Mine Safety and Health Administration (MSHA) standards. The insulation resists abrasion and chemicals.

Keep spools of wire in multiple colors on hand.

This wire meets stringent military specifications for material quality.

Use this wire in ovens, furnaces, and other electrical heating equipment where temperatures reach 480° F and higher.

A durable insulation withstands abrasion, so this wire can be pulled over rough surfaces.

The PEEK insulation on this wire won't degrade when exposed to radiation, and is often used in nuclear energy production.

Often used in mining applications, treatment plants, and motors, this wire withstands 5,000 volts AC/DC.

When pulled lengthwise, this unshielded wire extends 40% and then returns to its original length, so it's useful for high-vibration applications.

Eliminate tangles—the slippery insulation on this wire won't catch on itself, other wires, or on rough surfaces.

This wire meets SAE standards for low-voltage wiring in electrical systems for trucks, boats, trailers, and other vehicles. It's also known as primary wire and GPT wire.

Install this wire in conduit and cable trays throughout commercial and industrial buildings. It's also known as branch circuit wire.

Also known as photovoltaic (PV) wire, this wire is often used in solar panels and resists damage from UV light. It withstands 2,000 volts AC/DC.

Often used in automated applications such as robotics, this wire withstands continuous motion without degrading data or signal transmission.

The TPE insulation on this wire resists most chemicals, including oil and coolant, and withstands continuous motion.

Make connections in circuit boards with these short lengths of terminated wire.

Also known as Tefzel wire, this wire wraps around a post terminal to make an electrical connection, eliminating the need to solder wire onto circuit boards.

Designed for indoor applications, these cords are often used to power appliances.

Also known as hospital-grade cords, these cords have an extra-tight connection to prevent them from detaching. The plug is marked with a green dot.

After a power failure, these cords must be manually reset, preventing unexpected equipment startup.

The shielding blocks signal interference from nearby equipment and devices.

Create a vibration-resistant connection—the socket on these cords securely locks onto any male receptacle and will not detach until manually unlocked.

Also known as hospital-grade cords, these cords have an extra-tight connection to prevent them from detaching. The plug is marked with a green dot.

These cords work with any Milwaukee tool with a pin socket (Quik-Lok) connection.

Often used with 12 mm proximity switches, console lights, and valves.

The insulation on these cords resists abrasion, oil, and welding slag. They're rated NEMA 6P and IP67 to resist corrosion and withstand washdowns and temporary submersion.

Also known as pico cords, these cords are often used with low-current 8 mm proximity and photoelectric switches.

Plug these cords into computers, lab equipment, and office machines that have IEC connections.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Connect batteries to each other or to electrical systems.

The insulation on these cords resists water, so they can be used outdoors.

Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces.

Use these cords where ignitable gas and dust may be present. They're CSA certified for Class I, Division 1 and 2, Groups B, C, and D; and Class II, Division 1 and 2, Groups F and G hazardous environments.

Designed for indoor use, these cords are often used to power appliances.

Power multiple devices with one extension cord.

These self-coiling cords return to their retracted length after stretching for tangle-free storage.

Keep personnel safe from electric shock with these cords.

These cords have an oil- and water-resistant insulation and impact-resistant connectors for protection in harsh environments.

Give the connectors on these cords a quarter turn to lock in place.

An isolated ground connection on these outlets protects computers and other sensitive equipment from external signals that interfere with the equipment’s performance.

Often used in offices and workstations, these outlet strips power multiple devices from a single wall outlet.

The power switch to these outlet strips is on a 44" long cord, so you can control power even when the strips are in hard to reach places, such as under a desk.

Also known as hospital-grade outlet strips, these outlets have an extra-tight fit to prevent plugs from detaching. They are marked with a green dot.

Mount these outlet strips to a desktop or workbench with the mounting hardware, or set them on a surface.

Mount these strips into standard 19" wide electronics racks and enclosures.

Install these outlet strips in an opening in workbenches, tables, and other furnishings; the outlets lie flush with the surface for a seamless appearance.

Transmit audio, video, and data signals over long distances with minimal signal loss.

Often used in automated applications such as robotics, these cords withstand continuous motion without degrading data transmission.

The insulation serves as a tough armor that protects these cords in high-traffic areas.

Pinch the sides on the plugs of these cords to insert them; they lock into a socket to prevent the cord from detaching.