Because these switches mount flush against a panel, they're easy to clean and hard to damage.

A single-piece construction prevents the contact block from separating from the actuator in high-vibration applications.

Able to handle tough, repetitive use, these switches are more durable than standard plastic switches.

Immediately cut power with a single push.

Save space on a panel by using one switch to perform multiple switching functions.

Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.

Immediately cut power with a single push.

Sized for 4 mm or 6 mm panel cutouts, these switches are often used with circuit boards to control electronics.

Operate low-voltage devices that require less than 48 volts, such as doorbells and buzzers.

These aluminum switches are rated NEMA 4, NEMA 13, and IP66 for protection from washdowns and oil/coolant spraying.

Rated NEMA 4X and 13, all switches resist corrosion and can withstand washdowns and oil/coolant spraying.

More lightweight than steel or stainless steel, these aluminum enclosed switches are rated NEMA 4X for protection from corrosion and washdowns.

Immediately cut power with a single push.

Able to withstand high currents, these switches are often used with motors and pumps.

Choose from a variety of messages and colored lenses to combine a rocker with a base and wiring socket for a complete switch.

Rated IP67, these switches are protected from temporary submersion.

Choose an actuator and contact block to make your own 22 mm metal switch.

Choose an actuator and contact block to make your own 16 mm switch.

These switches meet MIL-S-3950.

Maximize the space in a panel—these switches are half the size of most toggle switches.

Able to withstand high currents, these switches are often used with motors and pumps.

Switches are rated NEMA 4, 13, and IP66.

Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Rated NEMA 3S, 4X and 13, these switches are protected from corrosion, washdowns, and oil/coolant spraying.

Press these switches with your foot for convenient, hands-free operation.

Safe for use in wet locations, these switches are IP and NEMA rated for protection from corrosion, washdowns, and oil/coolant spraying.

Apply pressure from any direction to actuate these switches.

These switches are rated for environments where hazardous material is present.

Control cranes and other mobile machinery in dirty, outdoor, and wet environments without damaging your switch.

With a slim shape, these switches fit comfortably in your hand.

Use these hand-held switches with mobile machinery.

Rated NEMA 4, these switches are protected from washdowns.

These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Install these key switches in 30 mm dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.

Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.

Prevent personnel from getting too close to dangerous equipment when equipment is on—these mats turn equipment off when someone steps on them or when a fault is detected.

At only 3/32" thick, these mats fit under carpeting or anywhere else you want to hide them.

Rated IP67 and NEMA 6, these switch mats withstand washdowns.

These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited.

Use fingerprints to confirm the identity of personnel before granting access to secure areas or equipment.

Pull the hanging rope in any direction to actuate these switches.

Rated IP69K, these switches can withstand high-pressure, high-temperature washdowns and temporary submersion.

Scanning 275° side-to-side for people and objects, these switches (known as safety laser scanners) cover large areas and send signals to machinery to prevent accidents.

A built-in relay produces AC voltage output. These switches are often used with older programmable logic controllers (PLCs).

For optimal performance in tight spaces, these switches have a smaller beam and can detect smaller objects than standard photoelectric switches.

The flexible cable on these switches withstands applications that require frequent motion, such as robotics.

Eliminate the need to calculate the sensing distance when using different metals—these switches sense all metal at the same distance. Also known as K=1 sensors.

Sense objects as they pass through the switch’s ring via tubing or a funnel. These switches are often used to monitor blockages, detect breaks in spooling wire, or count small metallic parts, such as screws, during the stamping process.

Use these switches to sense metallic objects in environments containing flammable gases and combustible dust. ATEX and IECEx certified to protect against explosion, they produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks.

Twist the sensor to detect metallic objects where explosive dust or gas may be present—the sensor rotates for front, side, top, or bottom sensing. These switches are UL and C-UL listed as well as ATEX and IECEx certified for hazardous locations.

These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.

These intrinsically safe switches detect objects as they’re routed through the ring. They produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks. Switches are ATEX certified to protect against explosion.

These switches have a longer sensing distance compared to other proximity switches with the same diameter.

Switches accept both AC and DC input voltage.

Mount these flat inductive switches to a base or rail to remotely detect metallic objects in wet and dirty environments.

These switches use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or produce sparks. ATEX certified, they protect against explosion in environments containing flammable gases and combustible dust. Switches sense both metallic and nonmetallic objects.

Easily mount these flat switches to a base or rail.

Mount proximity switches into a panel cutout or tank wall.