Built to handle tough, repetitive-use applications, these are more durable than standard straight-blade connectors.

Create a streamlined appearance—the flat face lies flush with your wall plate.

Access the wire connection by opening the hinged housing. These connectors have screw terminals to create a secure connection; wire must be stripped before winding around the screw terminal.

Install these receptacles indoors. They keep personnel safe from electric shock by adding ground fault protection.

Check the status of a ground connection—a green light signals that connectors have power and are safely grounded.

Visually confirm that connectors have power; they have an indicating light that is visible from any angle.

Protect computers and other sensitive equipment from electromagnetic interference (EMI). Also known as isolated ground receptacles.

Add a fuse to protect equipment from current overload.

Receptacles protect sensitive equipment from electromagnetic interference (EMI) and spikes in voltage.

When mated, connectors meet NEMA 6P, NEMA 12, and either IP67 or IP69K.

Add a fuse to protect equipment from current overload. When mated with a receptacle, these plugs have an extra-tight fit to remain secure in high vibration environments. They're also known as hospital grade plugs.

An indicating light that is visible from any angle lets you know when these plugs have power. They have an extra-tight fit when mated with a receptacle to withstand high vibration. Also known as hospital grade plugs.

Rated NEMA 6P and 13, IP66, and IP69K when mated, connectors withstand oil/coolant spraying, high-pressure, high-temperature washdowns, and are corrosion resistant so they can be used in marine environments.

A rubber housing protects these connectors from damage caused by drops and impact.

Use connectors where ignitable gas and dust may be present. They are UL listed for Class I, Division 1 and 2, Groups C and D; Class II, Division 1 and 2, Groups F and G; and Class III hazardous environments.

Keep personnel safe from electric shock by adding ground fault protection to all outlets on the same circuit. These receptacles mount to DIN rail.

Also known as hospital-grade receptacles, these have an extra-tight fit when mated to withstand high vibration. They prevent damage to electronic equipment caused by spikes in current. Mount to DIN rail.

Instead of hardwiring power supplies, appliances, and other electronic devices, these connectors let you plug in an IEC power cord and turn the power on and off without needing a separate switch.

With a built-in switch, these connectors run power to appliances, power supplies, and other electronic devices while also filtering damaging EMI (electromagnetic interference).

Bring power into electronic devices while protecting them from harmful electromagnetic interference (EMI).

Also known as twist-lock devices, these connectors withstand tough, repetitive use, and are more durable than standard turn-lock connectors. They turn to lock together when mated to prevent accidental disconnection.

Check the status of a ground connection—a green light signals that connectors have power and are safely grounded. They turn to lock together when mated to prevent accidental disconnection.

When mated, these connectors meet NEMA 6P for protection against washdowns and temporary submersion.

A rubber housing protects these connectors from damage caused by drops and impact. They turn to lock together when mated to prevent accidental disconnection.

Rated NEMA 6P, NEMA 13, IP66, and IP69K when mated, these connectors withstand high-pressure, high-temperature washdowns, oil/coolant splashing, and are corrosion-resistant so they can be used in high-vibration marine environments.

A quarter turn locks these connectors in an outlet to remain secure in high-vibration applications and prevent accidental disconnection. They are not compatible with NEMA configurations.

Protect mini connectors when not in use.

These connectors withstand corrosion, abrasion, and welding slag. They're often used with 18 mm and 30 mm proximity switches and limit switches.

Join two connectors that both have internal threads.

Protect screw-together M12 connectors when not in use.

Protect harsh environment M12 connectors when not in use.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Also known as pico connectors, these connectors are often used with 8 mm and smaller proximity switches and photoelectric switches.

The smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.

Protect Mil. Spec. connectors when not in use.

These connectors meet MIL-DTL-26482, so they're compatible with other products that meet the same standard. Quickly mate by pushing them together.

Configure a connector for your application—combine inserts for power and signal with a base and a hood.

Use these connectors in oily and washdown environments; they're rated NEMA 4X and 12. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

A rubber seal and stainless steel hardware give these connectors excellent chemical resistance. They're rated NEMA 12, 4X, and IP65 for protection against corrosion, oil, and washdown environments.

Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

Sets include a plug and socket with wire leads already installed, so they can be quickly added to existing wiring systems. They fit standard Molex plugs and sockets.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

Also known as power-pole connectors, these single-pole connectors join two pin connections, rather than a pin and socket. They stack from the top and sides to form any configuration.

Caps are watertight to protect safe-break plugs when not in use.

Use connectors where ignitable gas and dust may be present, such as in refineries and silos. They also prevent an electrical arc when separating mated connectors so you can safetly connect and disconnect with the power on.

Meet international standards IEC 309-1 and 309-2.

Quickly replace or add connectors to an existing wiring system—connectors come assembled with wire leads already installed. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.

Use these connectors in vehicles and other agricultural and construction equipment. They have a sealed nylon housing that resists corrosion and washdowns.

Protect high-current connectors when not in use.

Use these sockets with Allen-Bradley servomotor systems.

Connectors lock into place for a secure connection in high-vibration environments. They power small devices, such as chargers for electronics, from a vehicle. Also known as cigarette-lighter plugs and sockets.

Deliver power to welding cable. These connectors withstand the high temperatures and high current found in welding applications.

Separately control each device plugged into these strips—each outlet has its own power switch.

Save energy by automatically turning off unused outlets. The master outlet controls five outlets and shuts off power to the other outlets when a device plugged into the master is turned off.

An isolated ground connection on these outlets protects computers and other sensitive equipment from external signals that interfere with the equipment’s performance.

A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.

Connect multiple devices from a single outlet.

Create a permanent outlet system without opening walls. These outlet strips mount to a wall with clips and hardwire to an existing electrical system.

Install these extra-long strips onto the frame of an electrical cabinet.

Mount these strips into standard 19" wide electronics racks and enclosures.

Often used with 12 mm proximity switches, console lights, and valves.

Use these mini cords to carry higher currents than nano or micro cords.

Add grounding or surge suppression protection.

Add a USB cord to these chargers to power up mobile devices and other electronics.

Change the M8 8-pin connection on your Schunk gripper to wire leads for hardwiring robots that don’t have an M8 8-pin connection.