This raceway system is also known as wireway and wire trough.

In areas exposed to washdowns, chemicals, and corrosion, install this stainless steel raceway system that has gaskets at the connection points.

Surface mount with the adhesive back to route low-voltage data and control cable where you can't get inside walls.

Insert and remove cable at any point along the length of this open-top, hook-shaped raceway.

With a top that overhangs the cover, this raceway keeps out rain. It is rated NEMA 3R for protection from liquids and light splashing.

Often used as an alternative to cable ties, wire duct guides and organizes short runs of electrical wiring in enclosures, control panels, and machines.

Narrower slots and fingers create more access and routing points than on standard slotted wire duct.

Also known as conduit bodies, these ports provide access to wire and cable inside PVC conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Join pieces of conduit.

Join pieces of conduit.

Reduce the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Join different sizes of conduit.

Seal out moisture while reducing the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Attach conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Also known as conduit bodies, these ports provide access to wire and cable inside thick-wall (rigid) metal conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Join pieces of conduit.

Join pieces of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Slide these grommets into conduit ends to protect wire and cable from abrasion when being pulled.

Also known as electrical metallic tubing (EMT), this conduit has thin walls that easily bend with a conduit bender and can be cut with a hacksaw.

Join pieces of conduit.

Join pieces of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.

Make tight bends in machine and equipment wiring.

Visually identify different runs of wire and cable in machine and equipment wiring.

Join pieces of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Also known as antishort bushings, these grommets slide into the ends of conduit and armored cable to protect wire and cable from sharp edges.

Attach conduit to a knockout in an outlet box or enclosure.

Also known as Type B, this conduit is more crush and abrasion resistant than liquid-tight flexible plastic conduit.

These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.

In addition to resisting oil, this conduit resists lubricants and grease.

Run conduit in food areas—the cover can be cleaned and sterilized without weakening or splitting. This conduit meets NSF/ANSI standard 169 for special-purpose food equipment.

Covered with a copper braid, this conduit protects wire and cable from electromagnetic interference (EMI) caused by motors and other equipment.

Secure threaded plastic conduit fittings to a knockout in an outlet box or enclosure.

One end twists into a piece of conduit for a quick connection; the other end attaches to a knockout in an outlet box or enclosure.

Also known as Type A, this conduit meets the demands of continuous motion while sealing out liquid when used with liquid-tight fittings.

Transition between conduit sizes and types.

Curve these ramps to route cable around bends and corners in indoor areas with heavy pedestrian and equipment traffic.

These cable ramps handle heavy pedestrian and equipment traffic.

Multiple channels let you separate different types of cable and cords.

These cable ramps are strong enough to withstand equipment traffic.

The zinc plating on these tray systems offers good corrosion resistance.

Cut, bend, and connect these wire mesh tray systems to route cable and hose in configurations such as curves, slopes, and tees.

Thread cable and hose through the entire length.

Designed for smooth, quiet travel, these carriers minimize clicking and jumping in vibration-sensitive applications such as printing and scanning.

Bands of corrosion-resistant stainless steel surround flexible nylon to make these the most durable, protective enclosed carriers we offer.

Bending and twisting up to 380° in any direction, these carriers organize and protect cable and hose around machines that are constantly moving, such as robotic arms and conveyors.