Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control the brightness of lights on the same circuit. They're also known as three-way switches.

Rated IP65, these controls are protected from washdowns.

Screw these controls into a light bulb socket.

Smaller than standard size snap-acting switches, these fit in tight spaces.

Enclosures protect these snap-acting switches from the environment.

With a rubber-encased housing and stainless steel bracket, these switches resist vibration and corrosion. They're rated IP68 for protection from dust and temporary submersion.

Keep out dirt and moisture—the sealed housing on these switches is watertight and meets MIL-PRF-8805.

Often used on conveyor systems and bin filling operations, these switches have the rapid-closing action of a snap-acting switch but have a large actuator for sensing larger objects.

These switches actuate with the slightest push for a high degree of accuracy.

Secure these switches into panels using mounting nuts.

Rated IP67, these switches are protected from temporary submersion.

Rated NEMA 6P, 13, and IP67, these switches are protected from corrosion, oil/coolant spraying, washdowns, and temporary submersion.

Prevent equipment from automatically restarting—these switches must be manually reset each time they're actuated.

Use these switches where ignitable gas and dust may be present. They meet NEC Class I, Divisions 1 and 2, Groups B, C, and D; and Class II, Divisions 1 and 2, Groups E, F, and G for hazardous locations.

Replace access door hinges with these switches; they actuate when the door opens at least 4°.

Sensitive along their entire length, these switches are often used to signal when an overhead door closes or an item reaches the end of a conveyor.

Prevent automatic doors from closing on a person or an object—these switches immediately turn machinery off when actuated with minimal force.

Easily mount these flat switches to a base or rail.

With a smaller diameter and shorter length than standard sized switches, these fit in the most space-constrained areas.

These intrinsically safe switches detect objects as they’re routed through the ring. They produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks. Switches are ATEX certified to protect against explosion.

Use these switches to sense metallic objects in environments containing flammable gases and combustible dust. ATEX and IECEx certified to protect against explosion, they produce a low-current, low-voltage NAMUR signal, so they won’t ignite or create sparks.

These inductive proximity switches sense metallic objects each time they pass through the slot, even when they’re obscured by water, oil, dirt, or a surface finish. Use them to measure the speed of rotating equipment and to count or detect moving objects, such as sheet metal being fed into a stamping process.

Sense objects as they pass through the switch’s ring via tubing or a funnel. These switches are often used to monitor blockages, detect breaks in spooling wire, or count small metallic parts, such as screws, during the stamping process.

For use in volatile areas, these intrinsically safe switches detect objects when they pass through the slot. They use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or create sparks. ATEX and IECEx certified, they protect against explosion.

Mount these flat inductive switches to a base or rail to remotely detect metallic objects in wet and dirty environments.

Most often found in older devices, these switches require AC input voltage.

These switches have a longer sensing distance compared to other proximity switches with the same diameter.

A built-in relay produces AC voltage output. These switches are often used with older programmable logic controllers (PLCs).

With a narrow, flat body, these switches fit in tight spaces.

Light beams travel up to 32 ft. between the transmitter and receiver.

Safely detect the presence or absence of an object moving at high speeds with a light beam. These switches produce a low-current, low-voltage NAMUR signal, so they won’t create sparks or ignite. ATEX and IECEx certified, they protect against explosion in environments containing flammable gases and combustible dust.

Set these switches to delay activation by up to fifteen seconds after detecting an object.

Rated IP69K, these switches can withstand high-pressure, high-temperature washdowns and temporary submersion.

These switches use a NAMUR signal to operate at a low current and voltage, so they won’t ignite or produce sparks. ATEX certified, they protect against explosion in environments containing flammable gases and combustible dust. Switches sense both metallic and nonmetallic objects.

Often used with programmable logic controllers (PLCs), these switches use DC input voltage and produce PNP or NPN signal output.

Switches accept both AC and DC input voltage.

These switches sense when a valve is open or closed, supporting flow and temperature control within your system and offering reliable feedback.

Wire contacts to an alarm system to alert when doors or windows are opened.