These high-traction antislip coatings have zero VOCs and are low odor. They contain grit to provide traction for pedestrian, cart, and hand-truck traffic. Apply with a roller. The size listed is the combined total of the two parts.

These provide the highest traction and impact resistance of our antislip coatings. Longer-lasting than antislip tape, these coatings contain grit to provide traction. Apply with a roller. The resin and hardener come in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Coatings that meet MIL-PRF 24667C Type 1 are our most wear and impact resistant. They can also be applied with a notched trowel.

Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.

Water-based epoxy coatings are clear and can be applied over nearly any surface, even old coatings, without altering their appearance. These two-part coatings come with a mixer that attaches to a hand-held drill and a roller cover to apply them once mixed. The size listed is the combined total of the two parts.

Apply gallon-sized water-based coatings with a roller. Apply gallon-sized solvent-based coatings with a notched trowel, sprayer, or a roller cover for thick coatings (sold separately).

These thin primers penetrate deeply into concrete floors to create a hard surface that can then be coated with any urethane or epoxy coating. Primers resist abrasion and chemicals, such as mild acids, alkalies, salt, and fuel. Apply with a roller. The size listed is the combined total of the two parts.

Use these primers on your surface before antislip coatings to maximize longevity. They do not contain grit. Apply with a brush, roller, or sprayer. The size listed is the combined total of the two parts.

Patch concrete floors, stairs, and walls with these compounds.

Epoxy compounds are three-part compounds consisting of a resin, a hardener, and aggregate in separate containers that can be mixed in the pail. The size listed is the combined total of the parts. They have excellent impact and chemical resistance. Paste compounds are ready for foot traffic in 8-12 hours. Thick liquid compounds are ready for traffic in two hours, and can withstand steel wheels and forklifts.

Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds. Once cured, they withstand impact, abrasion, and chemicals. The size listed is the combined total of the two parts.

Polyurea compounds are ready for foot traffic in ten minutes and vehicle traffic in 30 minutes. They are self-leveling, but can be mixed with sand (not included) and applied with a trowel.

Epoxy compounds are ready for foot traffic in ten minutes and vehicle traffic in two hours. Urethane compounds are ready for foot traffic in five minutes and vehicle traffic in ten minutes. Both can be applied with a trowel when mixed with the included aggregate or used as a self-leveling compound when used alone. Mix in the included pail.

These leveling compounds stand up to acid and chemical spills, making them a good choice for corrosive environments. They also withstand steel-wheel traffic and heavy impact. Apply with a trowel. They're ready for foot traffic in 12 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Not only do these leveling compounds withstand severe abrasion, wear, and impact, they stand up to heavy steel-wheel traffic and heavy blows without cracking. Apply with a trowel. They're ready for foot traffic in 12 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Give new life to damaged and worn concrete floors. These leveling compounds also fill minor depressions and cracks. Apply with a trowel.

Epoxy compounds resist abrasion for use in high-traffic areas. They’re ready for foot traffic in 8 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.